Elo TouchSystems ET2201L User manual

User Manual –2201L
SW601363 Rev L, Page 1 of 25
USER MANUAL
Elo Touch Solutions
2201L Touchmonitors
SW601363 Rev L

User Manual –2201L
SW601363 Rev L, Page 2 of 25
Copyright © 2021ELO Touch Solutions. All Rights Reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical,
chemical, manual, or otherwise without prior written permission of ELO Touch Solutions.
Disclaimer
The information in this document is subject to change without notice. ELO Touch Solutions makes no representations or
warranties with respect to the contents herein, and specifically disclaims any implied warranties of merchantability or
fitness for a particular purpose. ELO Touch Solutions reserves the right to revise this publication and to make changes from
time to time in the content hereof without obligation of ELO Touch Solutions to notify any person of such revisions or
changes.
Trademark Acknowledgments
ELO Touch Solutions, IntelliTouch, iTouch, are trademarks of ELO Touch Solutions group of companies and its licensors.
Windows is a trademark of the Microsoft group of companies. Other product names mentioned herein may be trademarks
or registered trademarks of their respective companies. ELO Touch Solutions claims no interest in trademarks other than
its own.

User Manual –2201L
SW601363 Rev L, Page 3 of 25
Table of Contents
Chapter 1 - Introduction ........................................................................... 4
Chapter 2 –Installation............................................................................. 5
Chapter 3 –Mounting................................................................................ 9
Chapter 4 –Operation............................................................................... 10
Chapter 5 –Technical Support............................................................... 14
Chapter 6 –Safety & Maintenance........................................................ 15
Chapter 7 –Regulatory Information..................................................... 16
Chapter 8 –Warranty Information......................................................... 19

User Manual –2201L
SW601363 Rev L, Page 4 of 25
Chapter 1 - Introduction
Product Description
Your new touchmonitor combines ELO Touch Solutions reliable performance with the latest
developments in touch technology and display design. This combination of features creates a
natural flow of information between a user and the touchmonitor.
This touchmonitor incorporates a 24-bit color, active matrix thin-film-transistor LCD panel to
provide high quality display performance. Its Full HD resolution of 1920x1080 is suitable for
displaying graphics and images. Its LED backlight significantly reduces power consumption and
eliminates mercury (compared to CCFL-backlit panels). Other features that enhance this LCD
monitor’s performance are Plug & Play compatibility, built-in speakers and headphone output
capability, on-screen display (OSD) controls, and a family of peripherals including webcam and
magnetic stripe reader.
Precautions
Follow all warnings, precautions and maintenance as recommended in this user manual to
maximize the life of your unit and prevent risks to user safety. See the Safety & Maintenance
chapter for more information.
This manual contains information that is important for the proper setup and maintenance of the
unit. Before setting up and powering on your new touchmonitor, read through this manual,
especially the Installation, Mounting, and Operation chapters.

User Manual –2201L
SW601363 Rev L, Page 5 of 25
Chapter 2 –Installation
Unpacking the Touchmonitor
Open the carton and verify the following items are present:
•Touchmonitor with protective sheet for its face
•Quick Install Guide
•Japanese language regulatory information pamphlet
•DVI cable
•VGA cable
•USB cable
•Audio cable
•AC-DC power adapter
•North America, Europe power cables
•An approved power cord greater or equal to H05VV-F(For EUT weight > 3kg), 2G or 3G,
0.75mm² must be used
Connector Panel & Interfaces
Remove the cable cover on the back of the unit to access the touchmonitor’s connector panel.

User Manual –2201L
SW601363 Rev L, Page 6 of 25
Touchmonitor Connections
1. Connect the DVI or VGA video cables between the monitor’s DVI/VGA input connectors and
your DVI/VGA video source, respectively. Tighten the video cable’s screws for best
performance.
2. Connect the USB touch cable between the monitor’s USB connector and your PC’s USB
port.
3. Connect the audio cable between the monitor’s Audio In jack and your audio source.
4. Select the correct power cable for your region. Connect the cable between the AC power
source and the power adapter’s input connector. Connect the power adapter’s DC output
connector to the monitor’s input power jack.
5. Replace the cable cover, if desired. Cables can be routed inside the stand –remove and
replace the stand cable cover for access and routing.
6. The touchmonitor ships in an OFF state. Press the power button to turn it on.

User Manual –2201L
SW601363 Rev L, Page 7 of 25
Installing the Touch Technology Software Drivers
Some software installation is required for your iTouch Plus touchmonitor to work with your
computer. No additional drivers are required for your projected-capacitive touchmonitor with
Windows 7 and 8 operating systems, it uses Windows HID drivers.
To download latest touch drivers
1. Visit www.elotouch.com/Support/Downloads/Driver/DriverDownload/Default.aspx
2. Select the operating system from “Operating System” dropdown menu.
3. Select the technology from “Technologies” dropdown menu.
4. Click on the driver version required for your touchmonitor.
5. Click “Accept” once you are directed to the “Driver License Agreement” page.
6. Enter you email address, Click on “Next Step”. Your driver download will start automatically.
7. If you are a new user, fill in the required information and Click on “Register”. Your driver download
will start automatically.

User Manual –2201L
SW601363 Rev L, Page 8 of 25
Chapter 3 –Mounting
General Mounting Information
The OSD text can be rotated through the OSD menu to better suit your mounting orientation.
The holes located on the sides and top of the touchmonitor case are for ventilation. Do not
block, cover, or insert anything inside the ventilation slots.
Rear VESA Mount
Afour-hole 100x100mm mounting pattern for M4 screws (7mm x4) is provided on the rear of
the monitor. Remove the stand using a Phillips screwdriver to access this mounting
interface. The VESAFDMI-compliant mounting is coded: VESA MIS-D, 100, C
For use only with UL Listed Wall Mount Bracket or equivalent.
Stand Mounting
Threaded through-holes are provided on the bottom of the stand base for mounting or
securing.

User Manual –2201L
SW601363 Rev L, Page 9 of 25

User Manual –2201L
SW601363 Rev L, Page 10 of 25
Chapter 4 –Operation
Power
To turn the touchmonitor on or off, press the touchmonitor power button once.
The Power Status LED on the bottom of the touchmonitor functions according to the following
table:
TouchMonitor/Computer Module status
LED status
OFF
OFF
SLEEP
PULSING
ON
ON
The system consumes low power when in SLEEP and OFF modes. For detailed power
consumption specifications, refer to technical specifications on the Elo website
http://www.elotouch.com
Touching the screen will bring the attached host PC out of SLEEP mode (similar to moving the
mouse or pressing a keyboard key).
To improve reliability and reduce wasteful power consumption, disconnect the AC power cable
from the power adapter when long periods of disuse are planned.
Touch
Your IntelliTouch Plus touchmonitor is factory-calibrated and should not need manual calibration
(unless the input video is not fully scaled to the native resolution, or the touch experience needs
to be calibrated to a specific user).