Installation and Technical Information
BEGA
Due to the dynamic nature of lighting products and the associated technologies, luminaire data on this sheet is subject to change at the discretion of BEGA North America. For the most current technical data, please refer to bega-us.com
BEGA 1000 Bega Way, Carpinteria, CA 93013 (805)684-0533 © copyright BEGA 2020
Figure 1:
Overview:
LED Watts: 19.4W
System Watts: 24.0W
Controllability: 0-10V, TRIAC, and ELV dimmable
Weight: 10.1 lbs.
Protection Class: IP65
Tools Required:
• 4mm hex head screwdriver
• 6mm hex head screwdriver
10
1
4
"
39
3
4
"
3
1
2
"
27
1
4
"
4
1
8
"
7
1
2
"
2
1
4
"
60°
120°
180°
6
1
4
"
1
3
4
"
-
84100
SURFACE WASHER FLOODLIGHT -
OUTRIGGER ARM
11/12/2020
REV
PART NO.
SIZE
TYPE:
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY
OF BEGA NORTH AMERICA, INC.
ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN
PERMISSION OF BEGA NORTH AMERICA, INC. IS PROHIBITED.
DATE:
APPROVED:
P (805) 684-0533 - www.bega-us.com
DESCRIPTION:
1000 BEGA Way, Carpinteria, California 93013
B
SHEET 1 OF 1
NOT TO SCALE
DATE
DESCRIPTION
CHANGED BY
REV
Surface washer oodlight - outrigger arm 84 100
Dimensions
A: 10-1/4”
B: 4-1/8”
C: 27-1/4”
D: 7-1/2”
Maintenance:
Clean regularly with solvent-free cleaner
removing dirt and debris. Do not use high
pressure cleaners.
Replacement Parts
See label inside of xture for LED replacement
part number.
Consult factory for all other replacement
components.
Accessories
Please refer to the appropriate accessory installation
sheet for further instruction when applicable.
Updated: 11/16/20
84 100 1 of 2
C
D
B
A
Notice to Installer:
1. See page 2 for specic product safety warnings.
2. In conformance with UL Standard 1598, a silicone based sealant must be used be-
tween luminaire and supporting surface.
3. For ceiling and wall applications only.
4. Luminaire mounts directly to nished surface over a standard vertical single gang wir-
ing box (by others)
84100 Installation:
1. Loosen the (4) 4mm hex screw on the xture canopy to remove luminaire base.
2. Feed luminaire wiring through the luminaire base into wiring box.
3. Make supply wiring and luminaire wiring connections inside the wiring box:
MAIN VOLTAGE SUPPLY WIRE TO BLACK LUMINAIRE WIRE
NEUTRAL (COMMON) SUPPLY WIRE TO WHITE LUMINAIRE WIRE
GREEN GROUND WIRE TO GREEN LUMINAIRE WIRE
Dimming (if applicable):
DIMMING CONTROL WIRE (+) TO POSITIVE DRIVER DIM CONTROL WIRE
DIMMING CONTROL WIRE (-) TO NEGATIVE DRIVER DIM CONTROL WIRE
4. Mount luminaire to ceiling or wall surface using appropriate hardware by others. Fix-
ture mounts directly to nished surface over recessed wiring box.
5. Place a small bead of silicone around the back side of the mounting plate that will
come in contact with the nished surface (exterior applications only).
6. Replace luminaire canopy (with luminaire attached) and tighten (4) 4mm hex head
screws to secure into place.
7. To adjust head angle, use 6mm hex key to loosen joint at the head and/or canopy of
the xture. Adjust as needed and re-tighten to x in place.
