Endress+Hauser Proline Promass F 300 Instruction Manual

MANUAL
BA01807O/06/EN/01.17
Valid as of version 01.00 zz (Device rmware)
71382409
Proline Promass F 300 Coriolis Flowmeter
EtherNet/IP
Operating Instructions Manual
K
e
e
p
c
ov
er
h
t
i
g
t
w
h
i
l
e
S
p
a
n
nu
ng
ö
f
f
n
e
n

•M
ake sure the document is stored in a safe place such that it is always available when
working on or with the device.
• To avoid danger to individuals or the facility, read the "Basic safety instructions" section
carefully, as well as all other safety instructions in the document that are specific to
working procedures.
•
The manufacturer reserves the right to modify technical data without prior notice. Your
Endress+Hauser Sales Center will supply you with current information and updates to
these instructions.
Important
All information and technical specications in this documentation have been carefully checked and compiled by
the author. However, we cannot completely exclude the possibility of errors. TechnipFMC is always grateful to be
informed of any errors. Contact us on the website.
Smith Meter® is a registered trademark of TechnipFMC.
Technical Support
Contact Information:
Field Service Response Center
24/7 Technical Support/Schedule a Technician: 1-844-798-3819
System Installation Supervision, Start-Up, and Commissioning Services Available
Customer Support
Contact Information:
Customer Service
TechnipFMC
1602 Wagner Avenue
Erie, Pennsylvania 16510 USA
P: [phone]
F: [phone]
[e-mail]
TechnipFMC.com
Literature Library:
http://fmctechnologies.com/en/MeasurementSolutions/OnlineServices.aspx

Proline Promass F 300 EtherNet/IP Table of contents
3
Table of contents
1 About this document ................ 6
1.1 Document function ..................... 6
1.2 Symbols used .......................... 6
1.2.1 Safety symbols .................. 6
1.2.2 Electrical symbols ................ 6
1.2.3 Communication symbols ........... 7
1.2.4 Tool symbols .................... 7
1.2.5 Symbols for
certain types of information ......... 7
1.2.6 Symbols in graphics ............... 8
1.3 Documentation ........................ 8
1.3.1 Standard documentation ........... 8
1.3.2 Supplementary device-dependent
documentation .................. 9
1.4 Registered trademarks ................... 9
2 Basic safety instructions ........... 10
2.1 Requirements for the personnel ........... 10
2.2 Designated use ....................... 10
2.3 Workplace safety ...................... 11
2.4 Operational safety ..................... 11
2.5 Product safety ........................ 12
2.6 IT security ........................... 12
2.7 Device-specific IT security ................ 12
2.7.1 Protecting access via hardware write
protection ..................... 12
2.7.2 Protecting access via a password .... 13
2.7.3 Access via fieldbus ............... 13
2.7.4 Access via Web server ............ 14
2.7.5 Access via CDI-RJ45 service
interface ...................... 14
3 Product description ................ 15
3.1 Product design ........................ 15
4 Incoming acceptance and product
identification ..................... 16
4.1 Incoming acceptance ................... 16
4.2 Product identification ................... 17
4.2.1 Transmitter nameplate ........... 18
4.2.2 Sensor nameplate ............... 19
4.2.3 Symbols on measuring device ...... 20
5 Storage and transport ............. 21
5.1 Storage conditions ..................... 21
5.2 Transporting the product ................ 21
5.2.1 Measuring devices without lifting
lugs ......................... 21
5.2.2 Measuring devices with lifting lugs .. 22
5.2.3 Transporting with a fork lift ........ 22
5.3 Packaging disposal ..................... 22
6 Installation ....................... 23
6.1 Installation conditions .................. 23
6.1.1 Mounting position ............... 23
6.1.2 Requirements from environment and
process ....................... 26
6.1.3 Special mounting instructions ...... 28
6.2 Mounting the measuring device ........... 30
6.2.1 Required tools .................. 30
6.2.2 Preparing the measuring device ..... 30
6.2.3 Mounting the measuring device ..... 30
6.2.4 Turning the transmitter housing .... 31
6.2.5 Turning the display module ........ 31
6.3 Post-installation check .................. 32
7 Electrical connection .............. 33
7.1 Connection conditions .................. 33
7.1.1 Required tools .................. 33
7.1.2 Requirements for connecting cable ... 33
7.1.3 Terminal assignment ............. 36
7.1.4 Device plugs available ............ 36
7.1.5 Pin assignment of device plug ...... 36
7.1.6 Preparing the measuring device ..... 37
7.2 Connecting the measuring device .......... 37
7.2.1 Connecting the transmitter ........ 37
7.2.2 Integrating the transmitter into a
network ...................... 41
7.2.3 Connecting the remote display and
operating module DKX001 ........ 43
7.3 Ensure potential equalization ............. 43
7.3.1 Requirements .................. 43
7.4 Special connection instructions ............ 44
7.4.1 Connection examples ............. 44
7.5 Hardware settings ..................... 47
7.5.1 Setting the device address ......... 47
7.5.2 Activating the default IP address .... 48
7.6 Ensuring the degree of protection .......... 49
7.7 Post-connection check .................. 49
8 Operation options ................. 50
8.1 Overview of operation options ............ 50
8.2 Structure and function of the operating
menu .............................. 51
8.2.1 Structure of the operating menu .... 51
8.2.2 Operating philosophy ............ 53

Table of contents Proline Promass F 300 EtherNet/IP
4
8.3 Access to the operating menu via the local
display ............................. 54
8.3.1 Operational display .............. 54
8.3.2 Navigation view ................ 56
8.3.3 Editing view ................... 58
8.3.4 Operating elements .............. 60
8.3.5 Opening the context menu ......... 61
8.3.6 Navigating and selecting from list ... 62
8.3.7 Calling the parameter directly ...... 63
8.3.8 Calling up help text .............. 63
8.3.9 Changing the parameters ......... 64
8.3.10 User roles and related access
authorization .................. 64
8.3.11 Disabling write protection via access
code ......................... 65
8.3.12 Enabling and disabling the keypad
lock ......................... 65
8.4 Access to the operating menu via the Web
browser ............................. 66
8.4.1 Function range ................. 66
8.4.2 Prerequisites ................... 66
8.4.3 Establishing a connection ......... 68
8.4.4 Logging on .................... 70
8.4.5 User interface .................. 71
8.4.6 Disabling the Web server .......... 72
8.4.7 Logging out .................... 72
8.5 Access to the operating menu via the
operating tool ........................ 73
8.5.1 Connecting the operating tool ...... 73
8.5.2 FieldCare ..................... 77
8.5.3 DeviceCare .................... 78
9 System integration ................ 79
9.1 Overview of device description files ......... 79
9.1.1 Current version data for the device ... 79
9.1.2 Operating tools ................. 79
9.2 Overview of system files ................. 80
9.3 Integrating the measuring device in the
system ............................. 80
9.4 Cyclic data transmission ................ 80
9.4.1 Block model ................... 80
9.4.2 Input and output groups .......... 82
9.5 Diagnostic information via EtherNet/IP ..... 93
10 Commissioning .................... 98
10.1 Function check ....................... 98
10.2 Switching on the measuring device ......... 98
10.3 Connecting via FieldCare ................ 98
10.4 Setting the operating language ............ 98
10.5 Configuring the measuring device .......... 99
10.5.1 Defining the tag name ........... 101
10.5.2 Setting the system units ......... 101
10.5.3 Configuring the communication
interface ..................... 103
10.5.4 Selecting and setting the medium .. 105
10.5.5 Displaying the I/O configuration ... 107
10.5.6 Configuring the current input ..... 107
10.5.7 Configuring the status input ...... 109
10.5.8 Configuring the current output .... 109
10.5.9 Configuring the pulse/frequency/
switch output ................. 114
10.5.10 Configuring the relay output ...... 125
10.5.11 Configuring the local display ...... 128
10.5.12 Configuring the low flow cut off .... 139
10.5.13 Configuring the partial filled pipe
detection .................... 140
10.6 Advanced settings .................... 141
10.6.1 Using the parameter to enter the
access code ................... 142
10.6.2 Calculated values ............... 142
10.6.3 Carrying out a sensor adjustment ... 143
10.6.4 Configuring the totalizer ......... 144
10.6.5 Carrying out additional display
configurations ................. 147
10.6.6 WLAN configuration ............ 158
10.6.7 Configuration management ....... 160
10.6.8 Using parameters for device
administration ................ 161
10.7 Simulation .......................... 163
10.8 Protecting settings from unauthorized
access ............................. 167
10.8.1 Write protection via access code ... 167
10.8.2 Write protection via write protection
switch ....................... 169
11 Operation ....................... 170
11.1 Reading the device locking status ......... 170
11.2 Adjusting the operating language ......... 170
11.3 Configuring the display ................ 170
11.4 Reading measured values ............... 170
11.4.1 "Measured variables" submenu ..... 171
11.4.2 "Totalizer" submenu ............. 173
11.4.3 "Input values" submenu .......... 173
11.4.4 Output values ................. 175
11.5 Adapting the measuring device to the process
conditions .......................... 177
11.6 Performing a totalizer reset ............. 177
11.6.1 Function scope of the "Control
Totalizer" parameter ............ 178
11.6.2 Function scope of the "Reset all
totalizers" parameter ............ 178
11.7 Showing data logging ................. 179
12 Diagnostics and troubleshooting .. 184
12.1 General troubleshooting ................ 184
12.2 Diagnostic information via light emitting
diodes ............................. 187
12.2.1 Transmitter ................... 187

Proline Promass F 300 EtherNet/IP Table of contents
5
12.3 Diagnostic information on local display ..... 189
12.3.1 Diagnostic message ............. 189
12.3.2 Calling up remedial measures ..... 191
12.4 Diagnostic information in the Web browser .192
12.4.1 Diagnostic options .............. 192
12.4.2 Calling up remedy information .... 193
12.5 Diagnostic information in DeviceCare or
FieldCare ........................... 193
12.5.1 Diagnostic options .............. 193
12.5.2 Calling up remedy information .... 194
12.6 Diagnostic information via communication
interface ........................... 194
12.6.1 Reading out diagnostic information 194
12.7 Adapting the diagnostic information ...... 195
12.7.1 Adapting the diagnostic behavior ... 195
12.8 Overview of diagnostic information ....... 195
12.8.1 Diagnostic of sensor ............ 195
12.8.2 Diagnostic of electronic .......... 197
12.8.3 Diagnostic of configuration ....... 201
12.8.4 Diagnostic of process ............ 205
12.9 Pending diagnostic events .............. 209
12.10 Diagnostic list ....................... 210
12.11 Event logbook ....................... 211
12.11.1 Reading out the event logbook ..... 211
12.11.2 Filtering the event logbook ....... 211
12.11.3 Overview of information events .... 212
12.12 Resetting the measuring device .......... 213
12.12.1 Function scope of the "Device reset"
parameter .................... 213
12.13 Device information ................... 214
12.14 Firmware history ..................... 215
13 Maintenance .................... 216
13.1 Maintenance tasks .................... 216
13.1.1 Exterior cleaning ............... 216
13.1.2 Interior cleaning ............... 216
13.2 Measuring and test equipment ........... 216
13.3 Endress+Hauser services ............... 216
14 Repairs .......................... 217
14.1 General notes ....................... 217
14.1.1 Repair and conversion concept ..... 217
14.1.2 Notes for repair and conversion .... 217
14.2 Spare parts ......................... 217
14.3 Endress+Hauser services ............... 217
14.4 Return ............................. 217
14.5 Disposal ........................... 218
14.5.1 Removing the measuring device .... 218
14.5.2 Disposing of the measuring device .. 218
15 Accessories ...................... 219
15.1 Device-specific accessories .............. 219
15.1.1 For the transmitter ............. 219
15.1.2 For the sensor ................. 220
15.2 Communication-specific accessories ....... 220
15.3 Service-specific accessories .............. 220
15.4 System components ................... 221
16 Technical data ................... 222
16.1 Application ......................... 222
16.2 Function and system design ............. 222
16.3 Input .............................. 223
16.4 Output ............................ 226
16.5 Power supply ........................ 231
16.6 Performance characteristics ............. 232
16.7 Installation ......................... 237
16.8 Environment ........................ 237
16.9 Process ............................ 238
16.10 Mechanical construction ............... 242
16.11 Operability ......................... 246
16.12 Certificates and approvals .............. 251
16.13 Application packages .................. 253
16.14 Accessories ......................... 255
16.15 Supplementary documentation ........... 255
Index ................................. 257

About this document Proline Promass F 300 EtherNet/IP
6
1 About this document
1.1 Document function
These Operating Instructions contain all the information that is required in various phases
of the life cycle of the device: from product identification, incoming acceptance and
storage, to mounting, connection, operation and commissioning through to
troubleshooting, maintenance and disposal.
1.2 Symbols used
1.2.1 Safety symbols
Symbol Meaning
DANGER
DANGER!
This symbol alerts you to a dangerous situation. Failure to avoid this situation will
result in serious or fatal injury.
WARNING
WARNING!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can
result in serious or fatal injury.
CAUTION
CAUTION!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can
result in minor or medium injury.
NOTICE
NOTE!
This symbol contains information on procedures and other facts which do not result in
personal injury.
1.2.2 Electrical symbols
Symbol Meaning
Direct current
Alternating current
Direct current and alternating current
Ground connection
A grounded terminal which, as far as the operator is concerned, is grounded via a
grounding system.
Protective Earth (PE)
A terminal which must be connected to ground prior to establishing any other
connections.
The ground terminals are situated inside and outside the device:
• Inner ground terminal: Connects the protectiv earth to the mains supply.
• Outer ground terminal: Connects the device to the plant grounding system.

Proline Promass F 300 EtherNet/IP About this document
7
1.2.3 Communication symbols
Symbol Meaning
Wireless Local Area Network (WLAN)
Communication via a wireless, local network.
LED
Light emitting diode is off.
LED
Light emitting diode is on.
LED
Light emitting diode is flashing.
1.2.4 Tool symbols
Symbol Meaning
Flat blade screwdriver
Allen key
Open-ended wrench
1.2.5 Symbols for certain types of information
Symbol Meaning
Permitted
Procedures, processes or actions that are permitted.
Preferred
Procedures, processes or actions that are preferred.
Forbidden
Procedures, processes or actions that are forbidden.
Tip
Indicates additional information.
Reference to documentation.
A
Reference to page.
Reference to graphic.
Notice or individual step to be observed.
1.
,
2.
,
3.
… Series of steps.
Result of a step.
Help in the event of a problem.
Visual inspection.

About this document Proline Promass F 300 EtherNet/IP
8
1.2.6 Symbols in graphics
Symbol Meaning
1, 2, 3, ... Item numbers
1.
,
2.
,
3.
, … Series of steps
A, B, C, ... Views
A-A, B-B, C-C, ... Sections
-
Hazardous area
.
Safe area (non-hazardous area)
Flow direction
1.3 Documentation
For an overview of the scope of the associated Technical Documentation, refer to the
following:
• The W@M Device Viewer : Enter the serial number from the nameplate
(www.endress.com/deviceviewer)
• The Endress+Hauser Operations App: Enter the serial number from the nameplate
or scan the 2-D matrix code (QR code) on the nameplate.
For a detailed list of the individual documents along with the documentation code
→  255
1.3.1 Standard documentation
Document type Purpose and content of the document
Technical Information Planning aid for your device
The document contains all the technical data on the device and provides
an overview of the accessories and other products that can be ordered for
the device.
Sensor Brief Operating Instructions Guides you quickly to the 1st measured value - Part 1
The Sensor Brief Operating Instructions are aimed at specialists with
responsibility for installing the measuring device.
• Incoming acceptance and product identification
• Storage and transport
• Installation

Proline Promass F 300 EtherNet/IP About this document
9
Document type Purpose and content of the document
Transmitter Brief Operating
Instructions
Guides you quickly to the 1st measured value - Part 2
The Transmitter Brief Operating Instructions are aimed at specialists with
responsibility for commissioning, configuring and parameterizing the
measuring device (until the first measured value).
• Product description
• Installation
• Electrical connection
• Operation options
• System integration
• Commissioning
• Diagnostic information
Description of Device Parameters Reference for your parameters
The document provides a detailed explanation of each individual
parameter in the Expert operating menu. The description is aimed at
those who work with the device over the entire life cycle and perform
specific configurations.
1.3.2 Supplementary device-dependent documentation
Additional documents are supplied depending on the device version ordered: Always
comply strictly with the instructions in the supplementary documentation. The
supplementary documentation is an integral part of the device documentation.
1.4 Registered trademarks
EtherNet/IP™
Trademark of ODVA, Inc.
TRI-CLAMP®
Registered trademark of Ladish & Co., Inc., Kenosha, USA

Basic safety instructions Proline Promass F 300 EtherNet/IP
10
2 Basic safety instructions
2.1 Requirements for the personnel
The personnel for installation, commissioning, diagnostics and maintenance must fulfill
the following requirements:
‣Trained, qualified specialists must have a relevant qualification for this specific function
and task.
‣Are authorized by the plant owner/operator.
‣Are familiar with federal/national regulations.
‣Before starting work, read and understand the instructions in the manual and
supplementary documentation as well as the certificates (depending on the
application).
‣Follow instructions and comply with basic conditions.
The operating personnel must fulfill the following requirements:
‣Are instructed and authorized according to the requirements of the task by the facility's
owner-operator.
‣Follow the instructions in this manual.
2.2 Designated use
Application and media
The measuring device described in these Brief Operating Instructions is intended only for
flow measurement of liquids and gases.
Depending on the version ordered, the measuring device can also measure potentially
explosive, flammable, poisonous and oxidizing media.
Measuring devices for use in hazardous areas, in hygienic applications or where there is an
increased risk due to process pressure, are labeled accordingly on the nameplate.
To ensure that the measuring device remains in proper condition for the operation time:
‣Keep within the specified pressure and temperature range.
‣Only use the measuring device in full compliance with the data on the nameplate and
the general conditions listed in the Operating Instructions and supplementary
documentation.
‣Based on the nameplate, check whether the ordered device is permitted for the
intended use in the hazardous area (e.g. explosion protection, pressure vessel safety).
‣Use the measuring device only for media to which the process-wetted materials are
sufficiently resistant.
‣If the measuring device is not operated at atmospheric temperature, compliance with
the relevant basic conditions specified in the associated device documentation is
absolutely essential: "Documentation" section→  8.
‣Protect the measuring device permanently against corrosion from environmental
influences.
Incorrect use
Non-designated use can compromise safety. The manufacturer is not liable for damage
caused by improper or non-designated use.

Proline Promass F 300 EtherNet/IP Basic safety instructions
11
LWARNING
Danger of breakage due to corrosive or abrasive fluids!
‣Verify the compatibility of the process fluid with the sensor material.
‣Ensure the resistance of all fluid-wetted materials in the process.
‣Keep within the specified pressure and temperature range.
NOTICE
Verification for borderline cases:
‣For special fluids and fluids for cleaning, Endress+Hauser is glad to provide assistance
in verifying the corrosion resistance of fluid-wetted materials, but does not accept any
warranty or liability as minute changes in the temperature, concentration or level of
contamination in the process can alter the corrosion resistance properties.
Residual risks
LWARNING
The electronics and the medium may cause the surfaces to heat up. This presents a
burn hazard!
‣For elevated fluid temperatures, ensure protection against contact to prevent burns.
LWARNING
Danger of housing breaking due to measuring tube breakage!
‣In the event of a measuring tube breakage for a device version without rupture disk it is
possible for the pressure loading capacity of the sensor housing to be exceeded. This
can lead to rupture or failure of the sensor housing.
2.3 Workplace safety
For work on and with the device:
‣Wear the required personal protective equipment according to federal/national
regulations.
For welding work on the piping:
‣Do not ground the welding unit via the measuring device.
If working on and with the device with wet hands:
‣Due to the increased risk of electric shock, gloves must be worn.
2.4 Operational safety
Risk of injury.
‣Operate the device in proper technical condition and fail-safe condition only.
‣The operator is responsible for interference-free operation of the device.
Conversions to the device
Unauthorized modifications to the device are not permitted and can lead to unforeseeable
dangers.
‣If, despite this, modifications are required, consult with Endress+Hauser.
Repair
To ensure continued operational safety and reliability,
‣Carry out repairs on the device only if they are expressly permitted.
‣Observe federal/national regulations pertaining to repair of an electrical device.

Basic safety instructions Proline Promass F 300 EtherNet/IP
12
‣Use original spare parts and accessories from Endress+Hauser only.
2.5 Product safety
This measuring device is designed in accordance with good engineering practice to meet
state-of-the-art safety requirements, has been tested, and left the factory in a condition in
which it is safe to operate.
It meets general safety standards and legal requirements. It also complies with the EU
directives listed in the device-specific EU Declaration of Conformity. Endress+Hauser
confirms this by affixing the CE mark to the device.
2.6 IT security
We only provide a warranty if the device is installed and used as described in the
Operating Instructions. The device is equipped with security mechanisms to protect it
against any inadvertent changes to the device settings.
IT security measures in line with operators' security standards and designed to provide
additional protection for the device and device data transfer must be implemented by the
operators themselves.
2.7 Device-specific IT security
The device offers a range of specific functions to support protective measures on the
operator's side. These functions can be configured by the user and guarantee greater in-
operation safety if used correctly. An overview of the most important functions is provided
in the following section.
Function/interface Factory setting Recommendation
Write protection via hardware write
protection switch →  12
Not enabled. Individually following risk assessment.
Access code
(also applies for Web server login or
FieldCare connection) →  13
Not enabled
(0000).
Assign an individual access code during
commissioning.
WLAN
(order option in display module)
Enabled. Individually following risk assessment.
WLAN security mode Enabled (WPA2-
PSK)
Do not change.
WLAN passphrase
(password) →  13
Serial number Assign an individual access code during
commissioning.
WLAN mode Access Point Individually following risk assessment.
Web server→  14 Enabled. Individually following risk assessment.
CDI-RJ45 service interface →  14 – Individually following risk assessment.
2.7.1 Protecting access via hardware write protection
Write access to the device parameters via the local display, Web browser or operating tool
(e.g. FieldCare, DeviceCare) can be disabled via a write protection switch (DIP switch on

Proline Promass F 300 EtherNet/IP Basic safety instructions
13
the motherboard). When hardware write protection is enabled, only read access to the
parameters is possible.
Hardware write protection is disabled when the device is delivered →  169.
2.7.2 Protecting access via a password
Different passwords are available to protect write access to the device parameters or access
to the device via the WLAN interface.
• User-specific access code
Protect write access to the device parameters via the local display, Web browser or
operating tool (e.g. FieldCare, DeviceCare). Access authorization is clearly regulated
through the use of a user-specific access code.
• WLAN passphrase
The network key protects a connection between an operating unit (e.g. notebook or
tablet) and the device via the WLAN interface which can be ordered as an option.
User-specific access code
Write access to the device parameters via the local display, Web browser or operating tool
(e.g. FieldCare, DeviceCare) can be protected by the modifiable, user-specific access code
(→  167).
When the device is delivered, the device does not have an access code and is equivalent to
0000 (open).
WLAN passphrase
A connection between an operating unit (e.g. notebook or tablet) and the device via the
WLAN interface (→  75) which can be ordered as an option is protected by the
network key. The WLAN authentication of the network key complies with the IEEE 802.11
standard.
When the device is delivered, the network key is pre-defined depending on the device. It
can be changed via the WLAN settings submenu in the WLAN passphrase parameter
(→  159).
General notes on the use of passwords
• The access code and network key supplied with the device should be changed during
commissioning.
• Follow the general rules for generating a secure password when defining and managing
the access code or network key.
• The user is responsible for the management and careful handling of the access code and
network key.
• For information on configuring the access code or on what to do if you lose the
password, see the "Write protection via access code" section →  167
2.7.3 Access via fieldbus
When communicating via fieldbus, access to the device parameters can be restricted to
"Read only" access. The option can be changed in the Fieldbus writing access parameter.
This does not affect cyclic measured value transmission to the higher-order system, which
is always guaranteed.
For detailed information, see the "Description of Device Parameters" document
pertaining to the device →  255

Basic safety instructions Proline Promass F 300 EtherNet/IP
14
2.7.4 Access via Web server
The device can be operated and configured via a Web browser with the integrated Web
server (→  66). The connection is via the service interface (CDI-RJ45), the connection
for EtherNet/IP signal transmission (RJ45 connector) or the WLAN interface.
The Web server is enabled when the device is delivered. The Web server can be disabled if
necessary (e.g. after commissioning) via the Web server functionality parameter.
The device and status information can be hidden on the login page. This prevents
unauthorized access to the information.
For detailed information, see the "Description of Device Parameters" document
pertaining to the device →  255
2.7.5 Access via CDI-RJ45 service interface
The device can be connected to a network via the CDI-RJ45 service interface. Device-
specific functions guarantee the secure operation of the device in a network.
It is advisable to take relevant security concepts into consideration, such as those issued by
the Federal Office for Information Security. This includes organizational security measures
such as the assignment of access authorization as well as technical measures such as
network segmentation.
The device can be integrated in a ring topology. The device is integrated via the
terminal connection for signal transmission (output 1) and the connection to the
service interface (CDI-RJ45) →  42.

Proline Promass F 300 EtherNet/IP Product description
15
3 Product description
The device consists of a transmitter and a sensor.
The device is available as a compact version:
The transmitter and sensor form a mechanical unit.
3.1 Product design
5
4
Nicht unter
Spannung öffnen
Do not open when
energized
Ne pas ouvrir
sous tension
Power
I/O
N
i
c
ht
u
n
t
e
r
a
r
e
ö
f
f
n
e
n
D
i
s
p
l
a
y
+E
ESC
–
123
A0029586
 1 Important components of a measuring device
1 Connection compartment cover
2 Display module
3 Transmitter housing
4 Electronics compartment cover
5 Sensor

Incoming acceptance and product identification Proline Promass F 300 EtherNet/IP
16
4 Incoming acceptance and product
identification
4.1 Incoming acceptance
A0028673
1
2
1
2
Are the order codes on the
delivery note (1) and the
product sticker (2) identical?
A0028673
Are the goods undamaged?
A0028673
Order code:
Ser. no.:
Ext. ord. cd.:
ii
Date:
Do the nameplate data
match the ordering
information on the delivery
note?
A0028673
Is the CD-ROM with the
Technical Documentation
(depends on device version)
and documents present?
• If one of the conditions is not satisfied, contact your Endress+Hauser Sales Center.
• Depending on the device version, the CD-ROM might not be part of the delivery!
The Technical Documentation is available via the Internet or via the Endress+Hauser
Operations App, see the "Product identification" section →  17.

Proline Promass F 300 EtherNet/IP Incoming acceptance and product identification
17
4.2 Product identification
The following options are available for identification of the measuring device:
• Nameplate specifications
• Order code with breakdown of the device features on the delivery note
• Enter serial numbers from nameplates in W@M Device Viewer
(www.endress.com/deviceviewer): All information about the measuring device is
displayed.
• Enter the serial number from the nameplates into the Endress+Hauser Operations App
or scan the 2-D matrix code (QR code) on the nameplate with the Endress+Hauser
Operations App: all the information for the measuring device is displayed.
For an overview of the scope of the associated Technical Documentation, refer to the
following:
• The chapters "Additional standard documentation on the device" →  8 and
"Supplementary device-dependent documentation" →  9
• The W@M Device Viewer: Enter the serial number from the nameplate
(www.endress.com/deviceviewer)
• The Endress+Hauser Operations App: Enter the serial number from the nameplate or
scan the 2-D matrix code (QR code) on the nameplate.

Incoming acceptance and product identification Proline Promass F 300 EtherNet/IP
18
4.2.1 Transmitter nameplate
Order code:
Ser. no.:
Ext. ord. cd.:
ii
Date:
1 2 3 4 5
20
19
6
7
8
9
13 12 1011
18
17
16
14
15
A0029192
 2 Example of a transmitter nameplate
1 Manufacturing location
2 Name of the transmitter
3 Order code
4 Serial number (ser. no.)
5 Extended order code (Ext. ord. cd.)
6 Degree of protection
7 Space for approvals: use in hazardous areas
8 Electrical connection data: available inputs and outputs
9 2-D matrix code
10 Manufacturing date: year-month
11 Document number of safety-related supplementary documentation
12 Space for approvals and certificates: e.g. CE mark, C-Tick
13 Space for degree of protection of connection and electronics compartment when used in hazardous areas
14 Firmware version (FW) and device revision (Dev.Rev.) from the factory
15 Space for additional information in the case of special products
16 Permitted temperature range for cable
17 Permitted ambient temperature (Ta)
18 Information on cable gland
19 Available inputs and outputs, supply voltage
20 Electrical connection data: supply voltage

Proline Promass F 300 EtherNet/IP Incoming acceptance and product identification
19
4.2.2 Sensor nameplate
Order code:
Ser. no.:
Ext. ord. cd.:
ii
Date:
1
3
4
5
14
6
7
8
9
13
2
10
1112
A0029199
 3 Example of a sensor nameplate
1 Name of the sensor
2 Manufacturing location
3 Order code
4 Serial number (ser. no.)
5 Extended order code (Ext. ord. cd.)
6 Nominal diameter of the sensor; flange nominal diameter/nominal pressure; sensor test pressure; medium
temperature range; material of measuring tube and manifold; sensor-specific information: e.g. pressure range
of secondary containment, wide-range density specification (special density calibration)
7 Approval information for explosion protection, Pressure Equipment Directive and degree of protection
8 Flow direction
9 Manufacturing date: year-month
10 2-D matrix code
11 Document number of safety-related supplementary documentation
12 CE mark, C-Tick
13 Surface roughness
14 Permitted ambient temperature (Ta)
Order code
The measuring device is reordered using the order code.
Extended order code
• The device type (product root) and basic specifications (mandatory features) are
always listed.
• Of the optional specifications (optional features), only the safety and approval-
related specifications are listed (e.g. LA). If other optional specifications are also
ordered, these are indicated collectively using the # placeholder symbol (e.g. #LA#).
• If the ordered optional specifications do not include any safety and approval-related
specifications, they are indicated by the + placeholder symbol (e.g. XXXXXX-ABCDE
+).

Incoming acceptance and product identification Proline Promass F 300 EtherNet/IP
20
4.2.3 Symbols on measuring device
Symbol Meaning
WARNING!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in serious
or fatal injury.
Reference to documentation
Refers to the corresponding device documentation.
Protective ground connection
A terminal which must be connected to ground prior to establishing any other connections.