Energetics XT 420p User manual

CT 3.8, XT 420p
TZ-2175
EN
Computer manual

2
Table of contents
1. English P. 3
EN © The owner’s manual is only for the customer reference. ENERGETICS can not guarantee for mistakes occurring due to translation
or change in technical specification of the product.
© Copyright by ENERGETICS

3
Computer Instructions
THE DISPLAY AND IT’S SYMBOLS
BUTTON FUNCTIONS
MODE 1. Press the button to select TIME, DISTANCE and CAL to preset, and enter after setting. .
2. Press the button to scan trough the values in the display (Time – Calories – Odometer –
Pulse – Speed - Distance).
3. Press the button and hold for 2 seconds to reset all values to zero (except odometer).
SET To adjust the target value of TIME, DISTANCE and CAL.
Press the button and hold for 2 seconds to speed up the increasing.
RESET Press the button to reset the value.
Press the button and hold for 2 seconds to reset all values to zero (except odometer).
FUNCTIONS & OPERATIONS
1. Batteries Installation
Insert 2 pieces of AA 1.5V batteries in the battery case on the back of monitor.
Whenever batteries are removed or replaced, all values will be reset to zero except for the odometer.
2. Auto On/Off
While the user starts to do exercise, the display will show the workout value automatically. If the computer
does not receive a signal for more than 4 minutes the display will turn off automatically. All values are reset
to zero except for the odometer which will accumulate the total distance continuously.
3. Auto Scan
After the monitor is switched on, the LCD will display all values such as Time-Calories-Odometer-Pulse-
Speed- Distance alternating every 6 seconds.
4. Speed
Read out of the current speed in kilometres per hour, range from 0-99.9
5. Distance
An individual target distance may be preset by pressing MODE button. To adjust the value press SET
button, each key touch increases the value by 0.1 KM, hold the SET button for 3 seconds for fast increase.
Confirm the target setting by pressing MODE button. The display automatically shows the count down from
the target value to zero during exercise. If no target distance is preset, the distance counts up to 999.9 km.
MODE – scans through display
functions
Calories burned
Distance (Km)
Speed (Km/h)
Time (min; sec)
SET
– to confirm the
selection or value & increase
the parameters
EN
Pulse (beats per minute)
RESET – to set all values
back to zero (hold button)
Odometer accumulates total
distance (Km).

4
6. Time
An individual target time may be preset by pressing MODE button. To adjust the value press SET button,
each key touch increases the value by 1 minute. Confirm the target setting by pressing MODE button It
automatically counts down from the target value during exercise. If no target time is preset, the time counts
up from 00:00 to 99.59.
7. Calories
An individual target calorie consumption may be preset by pressing MODE button. To adjust the value
press SET button, each key touch increases the value by 1 calorie, as of 1000 each key touch will increase
by 10 calories. Confirm the target setting by pressing MODE. The display automatically counts down from
targeting value during exercise. If no target is preset the calories accumulate up to max 9999.
Note: This data is a rough guide which can not be used in medical treatment.
8. Odometer
Accumulates the total distance up to 999.9 km.
9. Pulse
The monitor will display the user's heart rate in beats per minute during training.
Note:
1. If the computer displays abnormally, please re-install the batteries at the back of the monitor.
2. Battery Spec: 1.5V UM-3 or AA (2 PCS).
3. The batteries must be removed and shall not be disposed in municipal waste. Dispose them according to
the local regulations.

Woelflistrasse 2
CH-3006 Bern
Switzerland
www.energetics.eu
© Copyright ENERGETICS 2012