Energetics XT 580 User manual

XT 580 Crosstrainer
Assembly manual
EN
Aufbauanleitung
DE
Montažni přiručka
CS
Manual na montaž
SK
Felhasznaloi kezikonyv
HU
60 -80 Min
110 kg
A: 160 cm
B: 127 cm
C: 58 cm
40 kg

2
Table of contents - Inhaltsverzeichnis -Obsah - Obsah - Tájékoztató
English
P
3
Deutsch
P
20
Česky
P
37
Slovensky
P
54
Magyar
P
71
Serial Decal / Seriennummeraufkleber / Štitek se seriovym čislem / Seriovy štitok / Cimke
EN
The product sticker is placed on the rear stabilizer on
bikes and ellipticals and next to the power inlet on
treadmills
DE
Der Aufkleber für die Seriennummer ist bei
Heimtrainern oder Ellipticals auf der hinteren Quer-
stütze angebracht, bei Laufbändern in der Nähe des
Stromanschlusses.
CZ
Štitek vyrobku se nachazi na zadnim tabilizatoru kol a
eliptickych trenažerůa vedle elektrickeho přivodu na b
ěžeckych trenažerech.
SK
Štitok vyrobku je umiestneny na zadnej strane
stabilizatora na bicykloch a kolesach a blizko pri
napajani na bežeckom pase.
HU
A termek ontapados cimkeje a kerekparok es
szobakerekparok hatso stabilizatoran van elhelyezve es
a pedalokon a tapbemenet mellett.
EN
© The owners manual is only for the customer reference. ENERGETICS can not guarantee for mistakes occurring due to translation
or change in technical specification of the product. Wherever pictograms are used they may differ from your product, it’s for
reference only.
DE
© Die Gebrauchsanweisung dient nur zur Referenz für den Kunden. ENERGETICS übernimmt keine Haftung für Fehler, die durch
Übersetzung oder technische Änderungen des Produkts entstehen. Falls Piktogramme verwendet werden, können diese von Ihrem
Produkt abweichen und dienen nur als Referenz.
CZ
© Navod k použiti je pouze doporučeni pro zakazniky. ENERGETICS nepřebira žadne ručeni za chyby způsobene překladem či změ
nami v technicke specifikaci vyrobku. Použiti piktogramův tomto navodu se může lišit od skutečneho použiti na vašem vyrobku,
rozmistěni v tomto navodu slouži pouze pro informaci.
SK
© Tento návod je určený len pre potrebu zákazníkov. ENERGETICS nezodpovedá za chyby, ktoré sa môžu vyskytnúť kvôli chybnému
prekladu alebo zmenám v technickej špecifikácii produktu. Všade, kde sa používajú piktogramy, sa tieto môžu líšiť od vášho produktu
a sú určené len na referenčné účely.
HU
© A vásárlók számára a jelen használati utasításnak csak ajánló jellege van. Az ENERGETICS cég nem vállal kezességet olyan jellegű
hibákért, amelyek az eredeti szöveg fordításából, illetve a termék módosított műszaki specifikációjából származnak. A használt
piktogramok eltérhetnek a termék piktogramjaitól. Ezek csak
tájékoztató jellegűek.

3
Corporate Social Responsibility
EN
INTERSPORT is a participating company in the BSCI (Business Social Compliance Initiative) based in
Brussels. Through BSCI, INTERSPORT is committed to implement the BSCI Code of Conduct in its supply
chain and to gradually achieve better working conditions at the involved suppliers’ workplaces. The BSCI
system is based on three pillars: monitoring of non-compliances by external independent audits;
empowering of supply chains’ actors through various capacitybuilding activities; and engagement with
all relevant stakeholders via constructive dialogue in Europe and supplying countries. Our social audits
are conducted by neutral, internationally recognized auditing companies with the aim of monitoring the
social compliance of our supplier factories.
For more information on the BSCI please visit: www.bsci-intl.org
Norms & Regulations
Consumer safety is the number one priority for ENERGETICS products. This means that all of our products
comply with national and international legal requirements (such as the EU Regulation (EC No.
1907/2006) concerning the Registration, Evaluation, Authorization and Restriction of Chemicals
[REACH]).
This product is also CE certified and has been tested by an internationally
recognized institute and certified against the industry standard EN 957.
Disposal of electrical waste products (Directive 2002/96/EC WEEE):
All products that contain electrical and electronic equipment must be marked
with the logo. These products shall not be disposed in municipal waste. Instead
please check local regulations regarding these types of products.
Disposal of batteries (Directive 2006/66/EG):
Batteries must be marked with the logo including the chemical symbols Hg, Cd
or Pb if the battery contains mercury, cadmium or lead above the threshold limits
mentioned in the directive and its amendments. Batteries used in products shall
not be disposed in municipal waste.
Directive 2011/65/EU:
Restriction of the use of certain hazardous substances in electrical and electronic
equipment (RoHS).

4
Dear Customer,
Congratulations on your purchase of an ENERGETICS home fitness equipment. This product
has been designed and manufactured to meet the needs and requirements of in-home use.
Please carefully read the assembly- and user manual. Be sure to keep the instructions for
reference and/or maintenance. If you have any further questions, please contact us. We wish
you lots of success and fun while training.
Your ENERGETICS - Team
Product Safety
ENERGETICS offers high quality home fitness equipment. All products have been tested and
certified according to the latest European Norm ISO EN 20957-1, EN 957-5.
Important Safety Instructions for all home fitness equipment
Do not assemble or operate this home fitness equipment outdoors or in a wet or moist
location.
Before you start training on your home fitness equipment product, please read the
instructions carefully.
Be sure to keep the instructions for information, in case of repair and for spare part
delivery.
This training equipment is not suitable for therapeutic purposes.
Consult your physician before starting with any exercise programs to receive advice on
the optimal training.
Warning: incorrect/excessive training can cause health injuries. Stop using the home
fitness equipment when feeling uncomfortable.
Warning: The safety level of the training equipment can only be maintained if it is
examined regularly on damage or wear.
Please follow the advice for correct training as detailed in the training instructions.
Ensure that training only starts after correct assembly, adjustment and inspection of the
home fitness equipment.
Always start with a warm-up session.
Only use original ENERGETICS parts as delivered (see partslist).
Follow the steps of the assembly instruction carefully.
Only use suitable tools for assembly and ask for assistance if necessary.
Place the home fitness equipment on an even, non-slippery surface for immobilization,
reducing noise and vibration.
To protect the floor or carpet from damage, place a mat under the product.
For all adjustable parts be aware of the maximum position to which they can be adjusted.
Tighten all adjustable parts to prevent sudden movement while training.
This product is designed for adults. Please ensure that children only use it under the
supervision of an adult.
Do not use the home fitness equipment without shoes or loose shoes.
Be aware of non-fixed or moving parts whilst mounting or dismounting the home fitness
equipment.
Search for noisy parts: If you should notice unusual noises, like grinding, clacking etc. try
to locate it and have it repaired by a professional. Make sure the home fitness equipment
is not used until after repairs have been made.

5
This device is not meant to be used by persons (including children) with limited physical,
sensory or mental capabilities or lacking experience and/or the knowledge to use this
device, unless under the supervision of another person in charge of their safety or having
been given prior instruction on the operation of this device.
Children should always be under supervision, to assure they are not playing with this
device.
The resistance level can be adjusted to your personal preference: see operations.
This product is made for home use only and tested up to a maximum body weight of: see
front page or serial decal on product.
WARNING: Heart rate monitoring systems may be inaccurate. Over exercising may result
in serious injury or death. If you feel faint stop exercising immediately.
Cleaning, Care & Maintenance on fitness equipment
Important
Frequent cleaning of your home fitness equipment will extend the product’s life.
Use of a home fitness equipment mat is recommended for ease of cleaning.
Use clean and proper sport shoes only.
Use a damp cloth to clean the home fitness equipment and avoid the use of
abrasives or solvents.
To prevent damage to the computer, keep liquids away and keep it out of direct
sunlight.
The home fitness equipment should not be used or stored in a moist area because
of possible corrosion.
In case of repair please ask your dealer for advice.
Replace defective components immediately and/or keep the equipment out of use
until repair.
Use original spare parts for repair only.
Daily
Monthly
Immediately wipe of the sweat;
perspiration can ruin the appearance
and proper function of the home
fitness equipment.
Check that all connecting elements
are tightly fitted and in good
condition.

6
Handling
Leveling
Transportation
After assembly, the rear stabilizer can be
adjusted to accommodate slightly uneven
ground. Turn the adjustment knobs at the ends
of the rear foot caps to level the rear stabilizer
to the floor.
The transportation wheels on the front foot caps
allow for easy manoeuvring. Simply pull back on
the handlebars until the wheels touch the floor.
Then roll the unit to a desired location.
Pedal Adjustment (where applicable)
A correct pedal adjustment will ensure you can do your exercise more efficiently and comfortable. It also
will reduce the risk of any injury while using.
1. Loosen the two screws underneath the pedal.
2. Slide the pedal back or forth until you found the
correct position.
3. Re-enter the two screws and tighten the nuts
securely.
4. You can start your exercise.
Make sure all screws are tightened well after you have made your adjustments.
Operations
Proper Training Clothes
Please make sure you always wear proper training shoes while working out. It is recommended that you
wear training appropriate exercise clothing’s that allow you to move freely whilst exercising.
Exercise Level
Please contact a physician before your exercise program. Immediately stop exercising if you feel any pain
or tightness in your chest, become short breathed of faint. Please contact your doctor before you start
using your fitness product again.
Resistance Adjustment
Manual adjustment
The resistance can be changed by turning the
resistance knob. To increase the resistance
turn the knob clockwise, to decrease it counter
clockwise.
Computer controlled adjustment
The resistance can be Increased or decreased on the console (if applicable). Please consult the computer
manual for further information.

7
Checklist

8
Part list
Part
Description
Qty
Part
Description
Qty
1
Main frame
1
50
Fixing plate for the magnet
1
2
Front stabilizer
1
51
Ladder bolt M10*1.5*58L
2
3
Allen bolt M8*1.25*80L
4
52L
Left handlebar
1
4
Adjustable cap
2
52R
Right handlebar
1
5L
Left moveable cap
1
53
Foam 500L
2
5R
Right moveable cap
1
54
Foam 560L
2
6
Curved washer D22xD8.5x1.5T
16
55
handlebar cap
2
7
Spring washer D15.4xD8.2x2T
18
56
Spring
1
8
Domed nut M8x1.25x15L
4
57
Flat washer D24*D13.5*2.5T
2
9
Allen bolt M8x1.25x20L
12
58
Screw ST4*1.41*12L
8
10
Handlebar post set
1
59
Ring
1
11
Pedal set
2
61
Crank axle
1
12
Supporting tube for moveable
handlebar
2
62
Round magnet
1
13
hand pulse cable
2
63
end cap
4
14
Bushing
14
64
Computer
1
15
Half ball cap
2
65
Handle pulse
2
16
Idle wheel
1
66
Flat washer D25xD8.5x2T
2
17
cover of pedal axle
2
68
moveable axle
1
18
Screw M8*1.25*16L
1
69
Front pedal axle
2
19
Rear stabilizer
1
70
Fixing plate of idle wheel
1
20
Square neck boltM6*1*45L
4
71
Bolt M6x1.0x15L
4
21L/
R
Pedals
1
72
handlebar set
1
22
Flat washer D23*D17.2*1.5T
1
73
Flat washer D14xD6.5x0.8T
4
23
screw cover D29*21(M8)
2
74
screw cover (M12)
2
24
Anti-loosen nut M10*1.25*7T
2
75
screw cover (M10)
2
25
Pin
6
76
Plastic cover
2
26
C-clip S-17(1T)
1
77
Club knob
4
28
pedal axle
2
78
Spring D1.2*55L
1
29
Upper computer cable
1
79
Nylon nut M6*1*6T
1
30
Lower computer cable
1
80
Screw ST4x1.41x10L
2

9
Part list
Part
Description
Qty
Part
Description
Qty
31
Belt wheel
1
81
Inner tube
1
32
C-clip D21.5xD17.5x1.2T
8
82
Nylon nut M10*1.5*10T
3
33
Crank set
2
83
Bolt M8*25
1
34
cross screw ST4.2x1.4x20L
9
85
Bolt M6*60L
1
35
Belt
1
86
Hex nut M6*1*6T
1
36L
Left chain cover
1
87
Flat washer D13*D6.5*1.0T
1
36R
Right chain cover
1
88
Joint
2
37
Fly wheel
1
89
Hex nut M8*1.25*6T
1
38
protective cover
1
90
Bolt M5x0.8x10L
4
39
Side cover
2
91
Screw ST4.0x1.41x20L
2
40
Hex bolt M8x1.25x25
2
92
Waved washer D17*D22*0.3T
1
41
Hex bolt M8*52L
1
93
Bushing D29*D11.9*9T
4
42
Round cover
2
94
Screw M8*1.25*16L
2
43
Bearing#6003ZZ
6
95
Nylon washer D6*D19*1.5T
1
44
Flat washer D20*D11*2.0T
2
96
Plastic washer D10*D24*0.4T
2
45
Nylon nut M8*1.25*8T
2
97
Tension knob
1
46
Flat washer D30*D8.5*2.0T
1
98
lower tension cable
1
47
Waved washer D26*D19.5*0.3T
6
99
cross bolt M5*0.8*10L
1
48
Nylon nut M6x1.0x6T
4
100
Anti-loosen nut
2
49
Upper protective cover
1

10
Assembly instruction
Step 1
1. Assemble the front stabilizer （2）and rear stabilizer (19) to the main frame by bolt(3), curved
washer(6), spring washer(7) and domed nut(8).
2. Adjust the proper height by turning the wheel of adjustable cap.

11
Step 2
1. Disassemble the bolt and washer attached from the tension knob (97).
2. Let the cable from tension knob (97) through into the handlebar post (10) as shown on figure a-
1.Then assemble the tension knob (97) on handlebar post by the bolt and washer from last step as
shown on figure a-2.
3. Connect the tension knob (97) with lower tension cable (98) as shown on figure c.
4. Assemble the left/right tube of pedal(11) to main frame by cover of pedal axle(17) and spacer (18)
as shown on figure d.

12
Step 3
1. Let the moveable axle (68) through the Supporting tube for left/right moveable handlebar（12）
and handlebar post (10) then fix them by screw cover(23), bolt(40), Spring washer(7), flat
washer(66) and waved washer(47)
2. Assemble the left handlebar(52L) and right handlebar(52R) to left/right moveable handlebar(12) by
Allen bolt(9), Spring washer(7), Spring washer(6).

13
Step 4
1. Fix the handlebar post (10) and main frame by Allen bolt(9), Spring washer(7), Spring washer(6)

14
Step 5
1. Let the cables from handlebar (72) through hole from the side of handlebar post (10) to the top
hole of handlebar post.
2. Fix the handlebar(72) to handlebar post(10) by Allen bolt(9), Spring washer(7), Spring washer(6)
3. Assemble the protective cover (38) to handlebar post (10).

15
Step 6
1. Connect the hand pulse cable (13) and upper computer cable (29) with the cables from computer
(64).
2. Fix the computer (64) onto the handlebar post (10) by screws (90).

16
Step 7
1. Assemble the left and right pedal to tube of pedal (11) by square neck(20),flat washer(73) , Club
knob(77).
2. The position of the pedals can be adjusted by three holes on tube of pedal (11).
3. Assemble the screw covers(74&75)

17
Computer manual ST6577-67
KEY FUNCTIONS
MODE
To confirm all settings.
Joggle wheel –UP
Rotate right (or press it) to select training mode and adjust function value up.
Rapidly rotate to increase the value fast.
Joggle wheel - DOWN
Rotate left (or press it) to select training mode and adjust function value down.
Rapidly rotate to decrease the value fast.
RESET
To clear the set-up value. Press RESET key and hold for 2 seconds to reset all
function figures.
TOTAL RESET
To power on the console again.
RECOVERY
To test heart rate recovery status
BODY FAT
To start or stop body fat testing.
FUNCTIONS
SPEED
Displays the user’s exercise speed.
RPM
Displays the pedaling Rotation Per Minute. The RPM and SPEED will switch to
another display in every 6 seconds after exercise starts.
TIME
1. You can use joggle wheel to set target time between 0:00 to 99:00 for
count down function.
2. It can be set up by the user or accumulated automatically for count up
function
DISTANCE
1. Your can use joggle wheel to set target distance between 0.00 to 99.50 for
count down function.
2. It can be set up by the user or accumulated automatically for count up
function.
CALORIE
1. You can use joggle wheel to set target calories between 0 to 9990 for count
down function.
2. It can be set up by the user or accumulated automatically for count up
function.
SCAN
Displays all function TIME→DISTANCE→CALORIES→PULSE→RPM/SPEED in
sequence.
BODY FAT
In STOP mode, press the BODY FAT button to start body fat measurement.
During measuring, user has to hold both hands on the handgrip. And the LCD
will display “-” “--““---” “----“ for 8 seconds until computer finish measuring.
LCD will display BMI, FAT% by turn every 3 seconds.

18
OPERATION PROCEDURE:
1. Installs 2 pieces of 1.5V #3 batteries, then the screen will display as following “Drawing A” and have
“Bi” sound at the same time, then enter to the personal data setting and press “MODE” button for
confirmation. After that, it goes to the next step to the main menu as “Drawing B”.
Drawing A
Drawing B
2. Get access to the set-up mode of TIME/DISTANCE/CALORIES/PULSE. When you are in each set- up
mode, for example in the time set-up mode, time value is blinking, you can use joggle wheel to adjust
the value and press “MODE” for confirmation. The set-up of DISTANCE, CALORIES & PULSE is the
same as TIME.
3. With any signal been transmitted into the monitor, the value of TIME, DISTANCE, CALORIES start to
count up as Drawing C. When there is any function has been preset the target (TIME or DISTANCE
or CALORIES), the function will be counting down from the preset to zero while the training starts.
Once the target is achieved to zero, the monitor start to beep for 8 seconds, and the function will be
counting up from zero directly if the training is going. Press “MODE” button for confirmation and
skip to next set-up.
4. In SCAN mode shown as “Drawing C”. RPM/SPEED/TM/DIST/CAL/PULSE will skip to display in every
6 seconds. The order is as follows.
Drawing C
5. You can also press “MODE” button to select single function display except RPM & SPEED function.
The RPM & SPEED function will switch display.

19
6. RECOVERY：
(1) When the user presses “RECOVERY”button, the RECOVERY function is active. At this time only
PULSE and TIME is working, other functions will not be displayed, and the Sensor Input is not
available. TIME starts to count down from “0：60”, Pulse signal will be blinking according user’s
heart rate BPM. When Time counts down to “0”, it will show F1~F6. (F1 is the best, F6 is the worst)
(2) LCD display as follows: (RECOVERY start condition & end condition).
(3) If the count down action to 0:00 is not completed and there is no pulse signal, the count down action
has to be done and shown F6.
(4) If you press the RECOVERY button prior to count down to 0:00, it will be end and return to the main
menu.
Note:
1. Stop training for 4 minutes, the main screen will be off.
You may press any button to have the computer restart working, the original value will retain.
(If re-install batteries, the original value will remove.)
2. If the computer displays abnormally, please re-install batteries and try again.
3. Battery Spec: 1.5V UM-3 or AA (2PCS).