ENFORCER E-921APQ User manual

ENFORCER Auto Dialer
16 SECO-LARM U.S.A., Inc.
Auto dialer will not arm/disarm
•
Make sure that you have entered the correct PIN
Number. Try re-entering it.
•While ressing and holding the [PROG] button, use a
en or a er cli to ress the [RESET] button on the
back of the dialer. This sets the PIN number to the
default (000).Then try to arm/disarm again.
Auto dialer will not dial out
•
Make sure that the tele hone line is working.
•Make sure that you have rogrammed at least one
tele hone number into the unit and that the full
number has been stored.
•Make sure that the system is in Auto Dial mode.
Unit doesn’t res ond to a call-back
•
Check to see if another unit (fax or answering
machine) could be answering the call and remove the
other unit.
•Adjust the call-in ring detect setting so that the auto
dialer will answer.
Difficulty in activating ‘room monitor’
by tele hone remote control
•
Try ressing the code key again.
•Move to a quieter location as ambient noise may
affect the auto dialer’s ability to detect the tone signal.
Troubleshooting:
NOTICE:
The information and s ecifications rinted in this manual are current at the time of ublication.
However, the SECO-LARM olicy is one of continual develo ment and im rovement. For this reason,
SECO-LARM reserves the right to change s ecifications without notice. SECO-LARM is also not res onsible
for mis rints or ty ogra hical errors.
Co yright © 2014 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be re roduced or
co ie
d, in whole or in art, without the written ermission of SECO
-
LARM.
WARRANTY:
This SECO
-
LARM roduct is warranted against defects in material and workmanshi while
used in normal service for one (1) year from the date of sale to the original customer. SECO-
LARM’s
obligation is limited to the re air or re lacement of any defective art if the unit is returned, trans ortation
re aid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, hysical
or electrical misuse or abuse, neglect, re air or alteration, im ro er or abnormal usage, or faulty installation,
or if for any other reason SECO-
LARM determines that such equi ment is not o erating ro erly as a result
of causes other than defects in material and workmanshi . The sole obligation of SECO-
LARM and the
urchaser’s exclusive remedy shall be limited to the re lacement or re air only, at SECO-
LARM’s o tion. In
no event shall SECO-
LARM be liable for any s ecial, collateral, incidental, or consequential ersonal or
ro
erty damage of any kind to the urchaser or anyone else.
SECO
-
LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco
-
larm.com
Phone: (949) 261
-
2999 | (800) 662
-
0800
Email: sales@seco
-
larm.com
IMPORTANT
:
Users and installers of this roduct are res onsible for ensuring this roduct com lies with all
national, state, and local laws and statutes related to monitoring and recording audio and video signals.
SECO-LARM will not be held res onsible for the use of this roduct in violation of any current laws or
statutes.
NOTE:
While the system can rovide valuable rotection to home and ro erty when ro erly installed, it
cannot guarantee com lete rotection against intrusion. SECO-LARM is not res onsible for any losse
s or
damage which may occur during the use of this roduct.
®
PIHLK1
MiE
-
921APQ_141029.docx
Auto Dialer
Manual
When triggered by an alarm system, the ENFORCER Auto Dialer can call u to 5 numbers. Each
number can contain u to 32 digits, including #, tones, and auses. The LCD shows the number being
dialed at each stage of the dialing rocess. The receiver can then listen in to sounds in the room and
disarm the system. The same functions are available by remote call in as well as arming the system.
The dialer includes a home mode (acting like a door chime when the owner is resent) and a anic
button. The 105dB built-in siren alarm can be rogrammed on or off. It also allows for the o tion of a
backu battery (not included) to continue offering rotection during a ower
loss and uses flash memory
to rotect against system data loss in case of extended ower failure.
Models Available
Certification
E-921APQ
E-921GPQ

ENFORCER Auto Dialer
2SECO-LARM U.S.A., Inc.
eatures:
•
16-Digit large dis lay with date/time and function icons
•2 (N.C.) Triggers for multi le zone security
•Remote monitoring – user can call in to listen in to room sounds and arm/disarm dialer
•Remotely listen in to room sounds or disarm during call back
•Programmable PIN number and entry delay timing
•5 Programmable emergency tele hone numbers (u to 32 digits each)
•Programmable auto-dialing cycle re eat times
•Home mode function (acts as a door chime when user is at home)
•Panic button
•Built-in flash memory to rotect against system data loss in case of ower failure
•Touch-Tone dialing
•Phone jack
•Low-battery indicator for backu battery (battery not included)
•DC ower in ut jack (3.5mm hone jack, not included)
•9V battery backu (battery not included)
•Wall-mountable
•Built-in 105dB alarm (with rogrammable alarm on/off)
•Built-in auxiliary out ut for external alarm or siren
Table of Contents:
Features
................................
.........................
2
Parts List ......................................................... 3
S ecifications ................................................. 3
Wiring Diagram ............................................... 3
Overview ......................................................... 4
LCD Screen Layout ........................................ 4
Installing the Auto Dialer ................................. 5
Programming the Auto Dialer ..................... 6~9
Setting and Changing the PIN Number ...... 6
Setting Emergency Phone Numbers ...... 6~7
Deleting a Stored Phone Number ............... 7
Setting the Siren Function .......................... 7
Setting the Auto Dial Function .................... 8
Setting the Number of Auto Dial Cycles ..... 8
Setting the Number of Call-in Rings ........... 8
Setting the Entry Delay Time ...................... 9
Setting the Date and Time
..........................
9
Testing the Auto Dial Function ........................ 9
Resetting the Auto Dialer ................................ 9
O erating the Auto Dialer ....................... 10~13
Arming and Disarming the System ........... 10
Panic Button Use ...................................... 10
Remote Control by Tele hone ............ 11~12
Home Mode Use ....................................... 12
Low-Battery Indicator ................................ 13
View Function ........................................... 13
Ti s ............................................................... 13
Also Available from SECO-LARM
®
........ 13
Program Planner ........................................... 14
Summary Programming/O eration Chart ..... 15
Troubleshooting ............................................ 16
ENFORCER Auto Dialer
SECO-LARM U.S.A., Inc. 15
Summary Programming/Operation Chart:
1. Setting/Changing PIN Number (see pg. 6)
Current PIN
[PROG]
[ARM/DISARM]
New PIN
[ARM/DISARM]
[PROG] x9
2. Setting Emergency Phone Numbers (see pgs. 6~ )
PIN
[PROG]
x2 [ARM/DISARM]
[#/DOWN] or
[*/UP]
Enter Phone
Number [ARM/DISARM]
[PROG]
x8
3. Deleting a Stored Phone Number (see pg. )
PIN
[PROG]
x2 [ARM/DISARM]
[#/DOWN] or
[*/UP] [DELETE/PAUSE] [ARM/DISARM]
[PROG]
x8
4. Setting the Siren Function (see pg. )
PIN
[PROG] x4
[ARM/DISARM]
[#/DOWN] or [*/UP]
[ARM/DISARM]
[PROG] x6
5. Setting the Auto Dial Function (see pg. 8)
PIN
[PROG] x5
[ARM/DISARM]
[#/DOWN] or [*/UP]
[ARM/DISARM]
[PROG] x5
6. Setting the Number of Auto Dial Cycles (see pg. 8)
PIN
[PROG] x6
[ARM/DISARM]
[#/DOWN] or [*/UP]
[ARM/DISARM]
[PROG] x4
. Setting the Number of Call-in Rings (see pg. 8)
PIN
[PROG] x7
[ARM/DISARM]
[#/DOWN] or
[*/UP]
[ARM/DISARM]
[PROG] x3
8. Setting the Entry Delay Time (see pg. 9)
PIN
[PROG] x8
[ARM/DISARM]
[#/DOWN] or [*/UP]
[ARM/DISARM]
[PROG] x2
9. Setting the Date/Time (see pg. 9)
PIN
[PROG]
x9 [ARM/DISARM]
[#/DOWN] or
[*/UP] [ARM/DISARM]
Re eat for each
osition
[PROG]
x2
10. Test Auto Dial Function (see pg. 9)
(In Standby Mode)
Press and Hold [PROG]
[#/DOWN] or [*/UP]
Check to see if number is dialed
11. Arm/Disarm System (see pg. 10)
PIN
[ARM/DISARM]
12. Remote Control by Telephone (see pgs. 11~12)
Receive Call
Press Key Code on Tele hone Key ad
Dial Voice Dialer Number
Press Key Code on Tele hone Key ad
13. Activate/Deactivate Home Mode (see pg. 12)
(In Standby Mode)
[HOME]
14. View (see pg. 13)
Last 5 Sensor Trigger Records
(In Standby Mode)
[#/DOWN]
Stored
Emergency Tele hone Numbers
(In Standby Mode)
[*UP]

ENFORCER Auto Dialer
14 SECO-LARM U.S.A., Inc.
Program Planner:
Program: Numbers
Date:
NUMBER
PRIORITY
TELEPHONE NUMBER
(include area code and dialer prefix as needed, add
PBX pause and extension if applicable, see p. 6-7)
NAME O PARTY TO BE REACHED
1
2
3
4
5
For Future Use
Installation
: Triggers
Date:
TRIGGER
GENERAL DESCRIPTION
SENSOR LOCATIONS
1
2
Use these charts during setu to record hone numbers and sensor locations for future reference.
It is recommended that you use a encil during setu and redo it in ink afterwards. The user
should kee in a safe, easily accessible location and a co y should be retained by the installer.
ENFORCER Auto Dialer
SECO-LARM U.S.A., Inc. 3
Back Connection Area (Cover Removed)
Wiring Diagram:
Trigger 1 Trigger 2
Siren
Out ut+
125mA Max.
DC+
9~12VDC
ENFORCER
®
Reset
GRD
COM.
or
Tele hone Wall Jack
External Alarm/Siren
Power Ada ter
(3.5mm Phone P
lug,
Not Included)
+
-
External Power
Su ly
+
-
SM
-
206Q*
E
-
964
-
D390Q*
* E
-
96
4
-
D390Q Photobeam Detectors, SM
-
200
Q
Magnetic
Sensors, and SM-206Q Concealed Magnetic Sensors shown as
exam les only: For other sensors and roducts available from
SECO
-
LARM, lease visit our website at www.seco
-
larm.com
.
SM
-
200Q*
O erating voltage
9~12 VDC
Current draw
Max. (at 12VDC)
Standby
5mA
Dialing
10
mA
Alarm On
1
8
0mA
Programmable emergency hone numbers
5
Maximum digits er tele hone number
32
Backu battery ty e/life (not
included)
9VDC/≈20h
Alarm sound level at 12" (30cm)
≥
105dB
Trigger in uts
2 x N.C. Trigger
Trigger in ut timer
≥500ms
Auxiliary out ut current (max)
125mA
O erating tem erature
32
°
~104°F (0
°
~40°C)
Storage tem erature
-
4
°
~140°F (
-
20
°
~60°C)
Weight
6.2
-
oz (175g)
Dimensions
3
3
/
8
"
x4
5
/
16
"
x1
7
/
8
"
(
86
x11
0
x4
7
mm)
Specifications:
1x
Auto dialer unit
1x
Tele hone cable
1x
Remote control instruction card
1x
Dual outlet tele hone jack ada ter
2x
Plastic wall anchors
2x
Wall mount screws
1x
Wall mounting tem late
1x
User manual
Parts List:

ENFORCER Auto Dialer
4SECO-LARM U.S.A., Inc.
Overview:
DC Power LED
Low Battery LED
LCD Dis lay
Numeric Key ad
Mounting Points
Terminal Block
Reset Button
Battery Rece tacle (Battery not included)
Siren S eaker
LINE Jack
DC Power Jack (for 3.5mm hone lug
ada ter, not included)
Home Mode Button
LCD Screen Layout:
Front
Back (Covers Removed)
2015
20152015
2015
-
--
-
01
0101
01
-
--
-
01
01 01
01
12
1212
12
-
--
-
0
00
0
0
00
0
PASSWORD
PASSWORDPASSWORD
PASSWORD MEMORY
MEMORYMEMORY
MEMORY LEARN
LEARNLEARN
LEARN
℡
℡℡
℡
CYCLE
CYCLECYCLE
CYCLE ENTRY
ENTRYENTRY
ENTRY 


Siren Alarm
Auto
Dial
Time/Date
Call
-
Back Rings
ARM
ARMARM
ARM
TRIGGER HOME
TRIGGER HOMETRIGGER HOME
TRIGGER HOME
Home Mode
Activated
Alarm Triggered
Left Side
Right Side
Armed or
Disarmed
Note: For ex lanation of these symbols, lease see Programming the Auto Dialer on ages 6~9.
ENFORCER Auto Dialer
SECO-LARM U.S.A., Inc. 13
LED Strobe Light
SL-1301-BAQ
Door/Window Switches,
Magnetic Contacts, etc.
Voice Dialer
E-921CPQ
Shock/Vibration Detector
SS-040Q
Tam er Switch
SS-072Q
Photobeam Sensor
E-931-S35RRQ
Operating the
Auto Dialer
, continued:
Low
-
Battery (LOW BATT.)
Indicator
When the charge level of the 9VDC backu battery (not included) is low, the “LOW BATT.” LED
will flash once every 1.5 seconds. Re lace the battery in order to continue roviding functionality
during a tem orary disru tion in ower.
Note:
In order
to avoid otential damage due to battery leakage
,
d
o not leave a low battery in
the unit. Also, be sure to remove the battery if the unit is unused for a eriod of time.
View Function
To view the last 5 sensor trigger events, while in standby mode ress the [#/DOWN] button.
To view stored emergency tele hone numbers, while in standby mode ress the [*/UP] button.
Note:
After 10 seconds of inactivity, the dialer will automatically exit the
view mode and return
to standby.
or a complete list
ing of SECO
-
LARM products, please visit us online at www.seco
-
larm.com.
Tips:
1. Make sure that the full tele hone numbers have been stored as they would normally be dialed
from a local hone.
2. The auto dialer is only suitable for single hone lines. It is not com atible with fax machines.
3. Set the number of Call-in rings to be less than the voicemail or message answer oint.
Also Available from SECO
-
LARM
®
:

ENFORCER Auto Dialer
12 SECO-LARM U.S.A., Inc.
Operating the
Auto Dialer
, continued:
Remote Control by Telephone – Function Explanations, continued:
END CALL
-
Pressing [3 #]
will end the call.
ARM SYSTEM – Pressing [5 #] during a user callback will arm the system, confirming with
three short “bee s,” and automatically hang u . If there are 5 ra id “bee s” after three short
“bee s,” it means a door/window is not closed. The dialer will then give 5 seconds to disarm
the system.
DISARM SYSTEM – Pressing [6 #] will disarm the system and automatically hang u .
Note:
If the user enters an incorrect assword or key code, the dialer will sound 5
“
bee
s”
and automatically hang u .
Home Mode
Use
To turn off the alarm function and use the dialer as a door chime, set the dialer to “Home” mode. A
chime will ring any time one of the sensors is triggered.
To activate the “Home” mode:
1. Press the [HOME] button on the left side of the dialer. One chime will sound and the word
‘HOME’ will a ear on the LCD screen.
2. After 60 seconds, another chime indicates that the dialer is now in the “Home” mode.
3. When a sensor is activated, the dialer will chime twice.
4. If the anic button is ressed, the dialer will sound a 30-second alarm and start the dialing
sequence to the rogrammed emergency numbers.
To deactivate the “Home” mode, sim ly ress the [HOME] button again.
Note:
Arming the system deactivates the “Home” mode. After disarming, reactivate the
“Home” mode if desired.
ENFORCER Auto Dialer
SECO-LARM U.S.A., Inc. 5
Installing the Auto Dialer:
Note: You can rogram the tele hone numbers and voice messages rior to connecting the
ower as long as the 9V battery is installed. The standby battery should rovide about 20 hours of
o eration.
Note: The Auto Dialer uses EEPROM to retain memory in the event of a ower loss.
1. Select a location for the dialer near a standard electrical
outlet (if user-su lied 12VDC ada ter is to be used), a
tele hone wall jack, and the alarm control anel, but out of
sight. The dialer should not be ex osed to direct sunlight or
rain, and must not be mounted near heat sources such as
radiators, heating ducts, or stoves.
2. For wall-mount, use the wall mounting tem late to drill
holes and attach 2 screws into the wall at the desired
location. For convenience, 5~6ft (1.5~2m) above the floor
is recommended (Fig. 1).
3. Remove the cable cover and battery cover from the back of
the auto dialer (Fig. 2).
4. Install a 9VDC backu battery (not included). Reattach the
battery cover.
5. Connect the dialer to two detectors or grou s of detectors in
series using the connection terminals as shown in the wiring
diagram (see g. 3). The dialer can also be connected to two
se arate alarm control anel out uts of a se arate alarm
system. If an external siren/alarm is desired, connect as shown
on the wiring diagram.
6. Power:
a. If the dialer is to be owered from the alarm control anel,
connect the alarm ower out uts to the terminal block (see g. 3).
b. If using a 12VDC ada ter (not included), lug the ada ter into the dialer’s DC ower jack.
7. Connect one end of the included tele hone cable to an existing Touch-Tone line wall socket,
and the other end to the dialer’s “LINE” jack. O tionally,
use the included dual outlet tele hone
jack ada ter to connect an extension tele hone using the tele hone’s cable (not included)
(Fig. 3).
8. For wall installation, lace the unit over the heads of the screws installed in ste 2 (Fig. 1) and
slide down. Check that the unit is firmly attached and tighten or loosen the screws as needed.
9. Once all connections are made, the dialer is ready to be rogrammed.
Fig. 3
Fig. 2
Cable
Cover
Battery
Cover
5~6ft
(1.5~2m
)
Fig. 1
9VDC Battery
(not included)

ENFORCER Auto Dialer
6SECO-LARM U.S.A., Inc.
Programming
the Auto Dialer:
The setu mode may only be accessed when the dialer is in standby mode. If no key is ressed
within 15 seconds, the dialer will automatically exit the setu mode.
Setting and Changing the PIN Number
1. Enter the current PIN number (factory reset PIN number is ‘000’), and ress the [PROG]
button once. ‘PASSWORD’ will flash on the LCD.
2. Press the [ARM/DISARM] button to acce t.
3. Enter a new PIN number (3-6 digits) followed by the [ARM/DISARM] button to confirm.
4. Press the [#/DOWN] or [*/UP] button to select other setu categories or ress the [PROG]
button until the rogramming icons disa ear to exit the setu mode.
Example
1
–
To store a number with area code 1
-
214
-
555
-
2858 and an office extension 205
(where the PBX requires a 2-second ause before the extension): After scrolling to the desired
number location, enter ‘12145552858,’ ress the [DEL/PAUSE] button for 2 seconds until the
letter ‘F’ a ears on the LCD screen, enter ‘205’ and ress the [ARM/DISARM] button.
Note:
If the PIN number is forgotten, ress and hold
the [PROG] button
and
use a en or
a er cli to ress the [RESET] button located under the cable cover on the back of the unit
and release. The unit will return to the factory reset PIN number (000). All other user
rogrammed settings exce t the date and time will be retained.
Setting Emergency Phone Numbers
1. Enter the PIN number and ress the [PROG] button twice or until “MEMORY” flashes on the
LCD screen.
2. Press the [ARM/DISARM] button to acce t.
3. Press the [#/DOWN] or [*/UP] button to select one of the number locations 1-5.
Note: The 5 number locations re resent the order in which the numbers will be dialed in the
case of an alarm.
4. Enter the number to store including any area codes or dialing refixes if needed (u to 32
digits, although only the last 16 digits can be shown on the LCD dis lay) using the key ad
followed by the [ARM/DISARM] button to acce t and store the number.
Note:
If needed, add a 4
-
second ‘ ause’ before a PBX extension number by ressing and
holding the [DEL/PAUSE] button for 2 seconds until the letter ‘F’ a ear
s on the LCD screen,
and then continuing with the extension number as usual. A ‘#’ or ‘*’ can also be entered by
ressing, and holding for two seconds, the [#/DOWN] or [*/UP] buttons res ectively. The ‘#’
sign shows as ‘
┘
’ and the ‘*’ sign shows as ‘
└
’ on the LCD screen.
ENFORCER Auto Dialer
SECO-LARM U.S.A., Inc. 11
Operating the
Auto Dialer
, continued:
Remote Control by Telephone
The system can be remotely controlled and monitored through any Touch-Tone hone, including
mobile hones. The user may arm or disarm the system as well as listen in on the room.
1. REMOTE CO TROL WHE ALARM IS ACTIVATED
When an alarm has been activated and the auto dialer dials the re- rogrammed emergency
numbers, the erson who answers the call will hear a single “bee " for a sensor trigger or 4
“bee s” for anic button activation and may ress one of the following function codes at any
time to control the system remotely:
unction
Press key code
Listen in
1 #
End call
3 #
Disarm system
6 #
The user should hear a “bee ” in res onse. If not, enter the function code again.
2. REMOTE CO TROL BY USER CALL-I (CALL BACK)
A. Using a mobile hone or any Touch-Tone hone, dial the hone number that the auto
dialer is connected to. The auto dialer will answer and “bee ” once after the number of
rings in the re- rogrammed call-in ringer detect cycle (3, 5, 7, or 10 rings, see g. 8).
B. Enter the PIN Number on the hone’s key ad. The dialer will “bee ” twice if the correct
code has been entered. If a wrong code is entered, the dialer will disconnect automatically
and the user must dial in again.
C. Press one of the following function codes to control the system remotely:
unction
Press key code
Listen in
1 #
Arm system
5 #
Disarm system
6 #
The user should hear a “bee ” in res onse. If not, enter the function code again.
Note:
Should the user have difficulty activating functions remotely by tele hone, there may
be too much ambient noise interference. Try ressing the code key again, or move to a
quieter location as ambient noise above 68dB may affect the auto dialer’s ability to detect the
tone signal.
3.
FU CTIO EXPLA ATIO S
LISTEN IN – Pressing [1 #] allows a user to hear sound in the room for 50 seconds. A “bee ”
will sound at 30 seconds to remind the user that the listen in time will soon end. Pressing [1 #]
again will reset the 50-second eriod, and entering any other key code will end monitoring and
erform the function. If there is no other key ress, the call will disconnect at the end of the 50
seconds.

ENFORCER Auto Dialer
10 SECO-LARM U.S.A., Inc.
Operating the
Auto Dialer
:
Arming and Disarming the System:
1. To arm the system, enter the PIN number and ress the [ARM/DISARM] button.
The dialer will sound three short “bee s” and the words “ARM” will a ear on the LCD screen.
After 60 seconds, there will be a single “bee ” tone to indicate that exit delay time has assed
and the alarm is now fully armed.
After the delay, when the system is fully armed, if a door or window connected to the alarm is
o ened, the LCD screen will flash the word “TRIGGER”. After the adjustable entry delay time
has assed, the siren will begin to sound (30 seconds on and 30 seconds off) and auto dialing
will commence according to the rogrammed sequence and cycle times. The call receiver will
hear a single “bee ” to indicate a sensor has been triggered or 4 “bee s” to indicate the
[PANIC] button has been ressed.
2. To disarm the system, enter the PIN number and ress the [ARM/DISARM] button.
The dialer will sound a long “bee ” and the word “ARM” will disa ear from the LCD screen.
Panic Button Use
1. When the [PANIC] button is ressed, the siren will sound immediately and auto dialing will
commence without delay.
If the siren has been rogrammed to “SOUND OFF” the siren will not
sound, but silent dialing will commence.
2. To cancel the alarm and sto auto dialing, enter
the PIN number and ress the [ARM/DISARM]
button. The dialer is now disarmed.
Note:
When the siren has been rogrammed to “
SOUND
OFF,” the siren will not sound
and the dialing will commence silently after the delay time has assed. When the call is
answered, the receiver will hear single “bee ” to indicate a sensor has been triggered or 4
“bee s” to indicate the [PANIC] button has been ressed.
Note: If the auto dialer is not connected to a working tele hone line, the dialer will “bee ”
4 times and the siren will begin to sound without attem ting to continue dialing out (this
overrides the “SOUND OFF” setting).
ENFORCER Auto Dialer
SECO-LARM U.S.A., Inc. 7
Deleting a Stored Phone Number
1. Enter the PIN number and ress the [PROG] button twice or until “MEMORY” flashes on the
LCD screen.
2. Press the [ARM/DISARM] button to acce t.
3. Press the [#/DOWN] or [*/UP] button to select the number you wish to delete.
4. Press the [DEL/PAUSE] button to delete the number.
5. Press the [#/DOWN] or [*/UP] button to select other setu categories or ress the [PROG]
button until the rogramming icons disa ear to exit the setu mode.
Learn
This function is unused.
Setting the Siren Function
This setting allows the user to choose between an audible alarm when triggered, or a ‘silent alarm’
while dialing the emergency numbers. The factory default is “ON”.
1. Enter the PIN number and ress the [PROG] button four times or until the alarm icon
( ) flashes on the LCD screen.
2. Press the [ARM/DISARM] button to acce t. The dialer will “bee ” once.
3. Press the [#/DOWN] or [*/UP] button to select either “SOUND ON” or “SOUND OFF” and ress
the [ARM/DISARM] button to acce t.
4. Press the [#/DOWN] or [*/UP] button to select other setu categories or ress the [PROG]
button until the rogramming icons disa ear to exit the setu mode.
Programming the
Auto Dialer
, continued:
Example 2 – To store a number with area code 1-949-555-1234, and an office extension #200
(where the PBX requires a 2-second ause before the extension): After scrolling to the desired
number location, enter ‘19495551234,’ ress the [DEL/PAUSE] button for 2 seconds until the
letter ‘F’ a ears on the LCD screen, ress the [#/DOWN] button for 2 seconds until the ‘
┘
’
a ears on the LCD screen, enter ‘200,’ and ress the [ARM/DISARM] button.
Example 3 – To store a local number 555-2858: After scrolling to the desired number location,
enter ‘5552858’ and ress the [ARM/DISARM] button.
5. Re eat for the other numbers to be stored (u to 5 total).
6. Press the [#/DOWN] or [*/UP] button to select other setu categories or ress the [PROG]
button until the rogramming icons disa ear to exit the setu mode.
Note: If the dialer is rogrammed to call a voice ager service which requires o erator assistance, the
service should be notified in advance regarding the meaning of the message. Consult local authorities
concerning the ermissibility of automatically dialing their emergency numbers before rogramming.

ENFORCER Auto Dialer
8SECO-LARM U.S.A., Inc.
Note:
1. When the dialer is in standby mode and the (℡
℡℡
℡) icon is ON, the auto dial is disabled.
2. When the dialer is in standby mode and the (℡
℡℡
℡) icon is OFF, the auto dial is enabled.
Setting the Auto Dial Function
The user can choose whether or not the dialer will dial the emergency numbers when triggered.
The factory default is “ON”.
1. Enter the PIN number and ress the [PROG] button five times or until the hone icon (℡
℡℡
℡)
flashes on the LCD screen.
2. Press the [ARM/DISARM] button to acce t.
3. Press the [#/DOWN] or [*/UP] button to select either “ON” or “OFF” and ress the
[ARM/DISARM] button to acce t. The dialer will “bee ” once.
4. Press the [#/DOWN] or [*/UP] button to select other setu categories or ress the [PROG]
button until the rogramming icons disa ear to exit the setu mode.
Programming the
Auto Dialer
, continued:
Setting the Number of Auto Dial Cycles
This can be set from 1~5 cycles. The factory default is 1 cycle, meaning that the auto dialer will
dial each rogrammed number 1 time.
1. Enter the PIN number and ress the [PROG] button six times or until “CYCLE” flashes on the
LCD screen.
2. Press the [ARM/DISARM] button to acce t.
3. Press the [#/DOWN] or [*/UP] button to select your choice of 1-5 cycles and ress the
[ARM/DISARM] button to acce t. The dialer will “bee ” once.
4. Press the [#/DOWN] or [*/UP] button to select other setu categories or ress the [PROG]
button until the rogramming icons disa ear to exit the setu mode.
Setting the Number of Call-in Rings
This sets the number of call-in rings after which the auto dialer will answer. The factory default is
5 rings, but can be user rogrammed for 3, 5, 7, or 10 rings.
1. Enter the PIN number and ress the [PROG] button seven times or until the bell icon ( )
flashes on the LCD screen.
2. Press the [ARM/DISARM] button to acce t.
3. Press the [#/DOWN] or [*/UP] button to select 3, 5, 7, or 10 and ress the [ARM/DISARM]
button to acce t. The dialer will “bee ” once.
4. Press the [#/DOWN] or [*/UP] button to select other setu categories or ress the [PROG]
button until the rogramming icons disa ear to exit the setu mode.
ENFORCER Auto Dialer
SECO-LARM U.S.A., Inc. 9
Setting the Entry Delay Time
This allows the user to set the length of time before the alarm will sound, to allow time to disable
the alarm after normal entry. The factory default is 20 seconds, but can be user rogrammed for 0,
5, 10, 15, or 20 seconds.
1. Enter the PIN number and ress the [PROG] button eight times or until “ENTRY” flashes on
the LCD screen.
2. Press the [ARM/DISARM] button to acce t.
3. Press the [#/DOWN] or [*/UP] button to select 0, 5, 10, 15, or 20 seconds and ress the
[ARM/DISARM] button to acce t. The dialer will “bee ” once.
4. Press the [#/DOWN] or [*/UP] button to select other setu categories or ress the [PROG]
button until the rogramming icons disa ear to exit the setu mode.
Setting the Date and Time
1. Enter the PIN number and ress the [PROG] button nine times or until the clock icon (



)
flashes on the LCD screen.
2. Press the [ARM/DISARM] button to acce t.
3. The date and time will a ear on the LCD screen as 5 sets of numbers re resenting the year,
month, date, hour, and minute res ectively. The first set of numbers (year) will be flashing,
indicating that this can now be changed.
4. Press the [#/DOWN] or [*/UP] button to select the correct number for the year and ress the
[ARM/DISARM] button to acce t and move to the next osition. Re eat for each osition until
com lete.
5. Press the [PROG] button until the rogramming icons disa ear to exit the setu mode.
Note: Time is shown using a 24 hour clock.
Programming the
Auto Dialer
, continued:
Testing the Auto Dial unction
:
To test the auto dial function, while in standby mode, ress and hold the [PROG] button for at least
two seconds. When you hear a ‘bee ’ tone, enter the memory location (1~5) of the number you
wish to test. The auto dialer should then dial the chosen number.
Resetting the Auto Dialer:
To reset the Auto Dialer, ress and hold the [PROG] button and use a en or a er cli to ress
the [RESET] button located under the cable cover on the back of the unit and release. The unit will
return to the factory reset PIN number (000). All other user rogrammed settings exce t the date
and time will be retained.