ENFORCER E-931CS22RFCQ User manual

Note: Model numbers that end with “Q” or that have a round green “Q” sticker signify RoHS-compliant products.
E-931CS22RFCQ
Wireless Entry Alert System
Manual
For monitoring a driveway or for use as an entrance indicator
No wiring necessary between sensor and speaker
Sensor range: Up to 22ft (7m)
Sensor is weatherproof for outdoor use
Speaker makes chime or alarm sound if beam is interrupted
Wireless range: Up to 328ft (100m) between the sensor and speaker
Each sensor can be paired with an unlimited number of speakers
Each speaker can be paired with up to 5 sensors

ENFORCER Wireless Entry Alert System
2SECO-LARM U.S.A., Inc.
Introduction:
The ENFORCER Wireless Entry Alert System is a self-contained easy-to-install alert system for commercial or home
applications. Each set contains a reflective photoelectric beam sensor that, when tripped, communicates wirelessly with a
speaker installed up to 328ft (100m) away*. An additional speaker may be installed to alert more than one area on the
property and an optional solar charger may be installed with the sensor for even more convenience.
Specifications:
Sensor
Speaker
Sensing range
Up to 22ft (7m)
N/A
Wireless range
Up to 328ft (100m)*
Operating frequency
433.92 MHz
Operating voltage
12VDC
Current draw
Standby
5mA
25mA
Active
20mA
100mA
Power input
2.5mm DC Jack
Light source
IR LED
N/A
Operating temperature
32°~122° F (0°~50° C)
Volume
N/A
0~90 dB
Alarm time range
N/A
3~30 s (Adjustable)
Speaker output
N/A
Chime/Off/Alarm (selectable)
IP Rating
IP55
N/A
Dimensions
31/4”x29/16”x11/2”
(82x66x38 mm)
31/4”x215/16”x19/16”
(83x75x40 mm)
Parts List:
Overview:
Optional Accessories:
Additional Wireless
Speaker
E-931ACC-SFQ
Digital Counter
E-931ACC-CQ
Replacement
Square Reflector
E-931ACC-R2Q
Solar Charger
for Sensor
E-931ACC-SPQ
Hood for Square and
Round Reflectors
E-931ACC-HR1Q
3” Round
Reflector
E-931ACC-RC1Q
Sensor
Reflector
Speaker
21/16”
(52mm)
23/8”
(61mm)
3/8”
(9mm)
*Range may vary greatly depending on the installation and operating environment.
19/16”
(40mm)
215/16”
(75mm)
31/4”
(83mm)
Alert tone
selection
Counter output
Timer
Volume
2.5mm
DC Plug
Mode button
1x Sensor
1x Speaker
1x Reflector
2x Power adapters
1x Small screwdriver
1x Mode adjustment pin
1x Sensor mounting bracket
2x Reflector/Speaker mounting bracket**
2x Bolts (Sensor)
2x Bolts (Reflector)
4x Nuts
5x Mounting screws
1x Screw anchor
1x Manual
Cable length: 97/8” (250mm)
31/4”
(82mm)
11/2”
(38mm)
29/16”
(66mm)
2.5mm
DC Jack
Alignment
LED
**Reflector and Speaker use the same mounting bracket.

ENFORCER Wireless Entry Alert System
SECO-LARM U.S.A., Inc. 3
Installation:
1. Install the reflector and sensor so they face each other about 2ft (61cm) off the ground.
2. Install the speaker within 328ft (100m) of the sensor.
3. Connect an included power adapter to the sensor. If optional solar charger is used, see pg. 4, Installing the Optional
Solar Charger.
4. Connect an included power adapter to the speaker.
5. To find the correct alignment, slowly adjust the angles of the sensor and reflector.
NOTE: Alignment is correct when the red LED turns OFF.
Mounting:
Programming the Speaker:
Sensor
Reflector
Speaker
1. Drill included screw into wall.
2. Hang speaker on screw.
1. Attach the sensor, reflector, or speaker to their respective brackets by using
the included bolts and nuts.
2. Mount the bracket to the wall using two of the included mounting screws.
1. Choose between Chime, Alarm, and Off using the alert tone selection switch on the side of the speaker.
2. Adjust the volume by using the included Phillips screwdriver to turn the volume adjustment screw. Turning clockwise
increases the volume; counter-clockwise decreases the volume.
3. Adjust the timer by using the included Phillips screwdriver to turn the timer adjustment screw. Turning all the way
clockwise will set the timer for 30 seconds; turning all the way counter-clockwise will set the timer for three seconds.
NOTE: Timer mode only applies if Alarm is chosen as the alert tone.
Pairing the Sensor and Optional Additional Speakers (E-931ACC-SFQ):
Use one of the two methods below to pair the optional additional speaker with the sensor.
Method 1:
1. Use the included mode adjustment
pin to press and hold the mode
switch until you hear a long beep
from speaker. This means the
speaker is in the learning mode.
2. Trigger the sensor by breaking the
beam. The speaker will beep once.
3. After 10 seconds, the speaker will
make one long beep indicating
successful pairing.
Method 2:
1. Remove the side panel of the
sensor with the included small
Phillips screwdriver.
2. Perform the point 1 of “Method 1”
and then press sensor’s learning
button once. The speaker will beep
once.
3. After 10 seconds, the speaker will
make one long beep indicating
successful pairing.
Clearing Memory:
1. Use the included mode adjustment
pin to press and hold the mode
switch until you hear a long beep
and two short beeps after five
seconds.
2. Release the mode button and the
memory has been cleared.
Connecting the Optional Counter (E-931ACC-CQ):
1. Connect the plug from the counter to the counter output jack of the speaker.
2. Test the counter. Each time the beam is broken, the counter should
automatically increase by 1.
3. Manually add or subtract 1 by pressing the “+” or “-“ buttons
4. Reset the counter by pressing “RESET”.
Learning button
NOTE: The speaker included with the Wireless Entry Alert System is pre-paired with the sensor.
IMPORTANT: When pairing additional speaker, release the mode switch immediately after two seconds and hearing the
long beep. Pressing the mode switch for more than five seconds will delete the memory.
Bracket
mounting
holes
Mounting with Bracket
Mounting Directly to Wall (Speaker Only)

ENFORCER Wireless Entry Alert System
4SECO-LARM U.S.A., Inc.
CAUTION: This sensor was not designed to prevent bodily injury or loss of life. Use of this sensor in certain security applications may be regulated by local laws
or codes. SECO-LARM is not responsible for compliance with such laws or codes.
FCC COMPLIANCE STATEMENT FCC ID: K4E931CS22RF
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his or her own expense.
Sensor does not detect object
Change the angle of the sensor or reflector
Red LED does not turn on
Change the angle of the sensor or reflector
Check power adapter and cable
Make sure solar charger is installed in an area exposed
to sunlight (E-931ACC-SPQ Only).
Speaker does not sound
Make sure speaker is switched to Chime or Alarm.
If using Alarm, make sure alarm duration is long enough.
Try pairing the sensor to the speaker. See Pairing the Sensor
and Optional Additional Speaker on page 3.
NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is one of continual
development and improvement. For this reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for
misprints or typographical errors.
Copyright © 2013 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission
of SECO-LARM.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for the life of the product from
the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation
prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a
result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the
replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or
property damage of any kind to the purchaser or anyone else.
SECO-LARM®U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA, 92606
Website: www.seco-larm.com
Tel: [phone] | [phone]
Email: [email protected]om
5. Connect the solar charger’s DC plug to the sensor’s DC
jack.
6. Attach the bracket to the solar panel by twisting into the
back of the solar panel until tight.
7. Adjust the solar panel and then tighten the adjustment
knob.
Installing the Optional Solar Charger (E-931ACC-SPQ):
1. Install the solar panel in an area exposed to sunlight.
2. Use the included Phillips screwdriver to remove the
side panel of the sensor.
3. Install the 3.7V lithium-ion battery included with the
solar charger into the sensor.
4. Replace the side panel.
Sample Applications:
Troubleshooting:
Storefront
Main Entrance
Driveway
PITSW3
MiE-931CS22RFCQ_1311.docx