ENFORCER E-931CS22RRC User manual

E-931CS22RRC
Range: 22ft. (7m)
Retro-Reflective Photoelectric
Sensor Entry Alert System
Sensor
Caution:
ENFORCER®
Included:
E-931ACC-R
Reflector
E-931CS22RRC
Transmitter/Receiver E-931ACC-S
Speaker/Electronic Chime
ENFORCER
®
ENFORCER
®
ENFORCER
®
E-931ACC-BLS4
E-931ACC-BLR1
Adapter
INSTALLATION MANUAL
Features:
••
••
•Retro-reflective photoelectric sensor.
••
••
•Range: Up to 22 feet (7m).
••
••
•Perfect for monitoring an entrance, or for counting
foot traffic with optional counter.
••
••
•Will make “ding-dong” sound or siren sound when
the beam is interrupted.
••
••
•Speaker volume can be adjusted or turned off.
••
••
•When in siren mode, sounding time is adjustable
from 3 to 30 seconds.
••
••
•9VDC adapter included.
•
This sensor was not designed to prevent bodily injury or loss of life.
• Use of this sensor in certain security applications may be regulated by local laws or codes.
SECO-LARM is not responsible for compliance with such laws or codes.
••
••
•All components plug into each other.
No hard wiring required.
••
••
•Optional counter available (E-931ACC-C).
••
••
•Optional second speaker available (E-931ACC-S).
••
••
•Includes the following:
— Retro-reflective photoelectric sensor.
— Reflector.
— Speaker/electronic chime.
— 9VDC adapter.

Specifications:
Troubleshooting:
Dimensions:
E931S22RRC_101204.pmd PITSW3
®
E-931CS22RRC
Retro-Reflective Photoelectric Entry Alert System
22' (7 m)
Sensor: 8-13 VDC, Chime: 12VDC
100mA Max.
30mA
IR LED
Relay (AC 120V/DC 24V, 2A)
-4
0
F (-20
0
C) ~ 122
0
F (50
0
C)
~1 sec. for Chime, 30 sec. for Alarm
Adjustable from 0 ~ max.
Adjustable 3~30sec. for alarm
Ground output (100mA)
Chime / Off /Alarm (Select by switch)
All Included
Model Number
Type
Sensing Range
Voltage Supply
Total Current Consumption
Stand-by Current
Light Source
Control Output
Ambient Temperature
Speaker Response Time
Speaker Volume
Alarm Time Range
External Chime Output
Speaker Output
Mounting Brackets
Red LED does not turn on. 1) Reflector and/or sensor is misaligned.
2) No power.
1) Adjust the reflector and/or sensor for
proper alignment
2) Check power adapter and cable.
Sensor does not detect the object. Sensor not aligned properly. Change the angle of the sensor or
reflector.
Trouble Remedy(s)Possible Origin(s)
NOTICE: The information and specifications printed in this manual are current at the time of publication. However,
the SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right
to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2004 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole
or in part, without the written permission of SECO-LARM.
SECO-LARM®U.S.A., Inc., 16842 Millikan Avenue, Irvine, CA 92606 Tel: [phone]
Fax: [phone] Website: www.seco-larm.com E-mail: [email protected]
WARRANTY: ENFORCER Photobeam Sensors are warranted against defects in material and workmanship while
used in normal service for a period of one (1) year from the date of sale to the original customer. Our obligation is
limited to the repair or replacement of any defective part if the unit is returned, transportation pre-paid, to SECO-LARM.
23/8" (60mm)
5/16" (8mm)
2" (50mm)
2" (50mm)
27/16" (62mm)
213/16" (71mm)
23/8" (60mm)
13/8"
(35mm)
13/16" (30mm)
2" (50mm)
213/16" (71mm)
23/8" (60mm)

Wiring: (one speaker, no counter)
W
e
m
e
c
l
o
Other possible applications: Offices, stores, schools, warehouse, vehicle detection, etc.
Wiring: (one speaker, with optional counter)
Wiring: (with optional counter and second speaker)
¤¤¤¤¤¤¤
¤¤¤¤¤¤¤
¤¤¤¤¤¤¤
¤¤¤¤¤¤¤
¤¤¤¤¤¤¤
¤¤¤¤¤¤¤
Garage
door
¤¤¤¤¤¤¤¤¤¤
¤¤¤¤¤¤¤¤¤¤
¤¤¤¤¤
¤¤¤¤¤
Sample Installations:
Main
entrance
door
Reflector
Sensor Adaptor
Input
Up to 22' (7m)
Speaker
ENFORCER
®
DC 9V
Reflector
Sensor Adaptor
Input
Up to 22' (7m)
Speaker
ENFORCER
®
Counter (optional)
Output
DC 9V
Reflector
Sensor Adaptor
Input
Up to 22' (7m)
Speaker
ENFORCER
®
Counter (optional)
DC 9V
Speaker (optional)
ENFORCER
®
Input
Output
Store front door
¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤
¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤

Mounting the Reflector:
Installation and Adjustment:
Sample Fixed Mounting:
Mounting the Sensor:
Mounting the Speaker/Electronic Chime:
Sample
Fixed
Mounting:
Sample
Bracket
Mounting:
Adjusting the Speaker/Electronic Chime:
LED Functions:
RED LED - When ON, it indicates the sensor is
powered and aligned properly.
Installation:
1. Mount the reflector and sensor so they face each
other at about 2' off the ground or knee high.
2. Connect the sensor to the speaker.
3. Connect power adaptor to the speaker.
••
••
•For signalling in multiple rooms, add an optional
second speaker (E-931ACC-S).
••
••
•Connect an optional counter (E-931ACC-C) to the
speaker output (if desired).
4. To find the correct alignment, slowly adjust the
angles of the sensor and/or reflector up and down
and right and left.
NOTE:Correct alignment is reached when red LED
turns ON.
Set Speaker Mode:
After the sensor and reflector have been properly
installed, the next step is to set the speaker mode.
1.
Choose between "Chime" or "Alarm" sound or "OFF".
2. If "Alarm" was chosen:
A. Set speaker to Alarm
B. Adjust the alarm sounding time from 3 to 30
seconds.
C. Set speaker Volume.
3. If "Chime" was chosen: Set speaker to Chime
4. If "OFF" was chosen:
A. Set speaker to OFF
B. The speaker will not sound when the beam is
broken.
Using the Optional Counter:
1. Automatically increases by "1" when sensor is
triggered.
2. Manually add "1" by pressing "+".
3. Manually subtract "1" by pressing " - ".
4. Reset counter by pressing "RESET."
Testing:
1. Power up the sensor and speaker. The red LED
should be ON.
2. Pass object to be detected between the sensor
and reflector. The red LED should turn OFF and
the speaker (if connected) should sound.
Red LED
ENFORCER®
Switch: Chime/
OFF/Alarm
Timer: 3~30 Sec.
Volume:0 ~ max
Switch
Wall mount hole
Bracket
mounting
holes