Epson S1S65010 User manual

Evaluation Board Technical Manual
Network Camera Controller with JPEG Encorder
(S5U1S65K01H0100/S5U1S65K01H1100)
S1S65010

NOTICE
No part of this material may be reproduced or duplicated in any form or by any means without the written permission
of Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does not
assume any liability of any kind arising out of any inaccuracies contained in this material or due to its application or
use in any product or circuit and, further, there is no representation that this material is applicable to products
requiring high level reliability, such as medical products. Moreover, no license to any intellectual property rights is
granted by implication or otherwise, and there is no representation or warranty that anything made in accordance with
this material will be free from any patent or copyright infringement of a third party. This material or portions thereof
may contain technology or the subject relating to strategic products under the control of the Foreign Exchange and
Foreign Trade Law of Japan and may require an export license from the Ministry of International Trade and Industry
or other approval from another government agency.
All product names mentioned herein are trademarks and/or registered trademarks of their respective owners.
SEIKO EPSON CORPORATION 2005 All rights reserved.

Configuration of product number
Device
S1 S 65010 F00A1 00
Packing Specification
Specification
Package
[F: QFP]
Model Code
Product Classification 2
[S: Communication]
Product Classification 1
[S1: Semiconductor IC]
Evaluation Board
S5U 1S 65K01 H100
Packing Specification
Board Revision
Category
[H: Hardware, S: Software]
[65K01: S1S65010]
Corresponding Device Model Code
Product Classification 2
[1S : Semiconductor IC for Communication]
Product Classification 1
[S5U: Development Tools for Semiconductor]
x
Board Code
[0: Main Board, 1: Camera Board]

Contents
S1S65010 EPSON i
Evaluation Board Technical Manual (Rev. 1.1e)
Contents
1. OVERVIEW .......................................................................................................................1
2. COMPONENTS.................................................................................................................1
2.1. Main Board (Product Number S5U1S65K01H0100)..............................................................1
2.2. Camera Board (Product Number S5U1S65K01H1100).........................................................1
2.3. Block Diagram........................................................................................................................2
3. MECHANICAL SPECIFICATIONS....................................................................................3
3.1. Main Board (Product Number S5U1S65K01H0100) Layout and Dimensions ...................................3
3.2. Camera Board (Product Number S5U1S65K01H1100) Layout and Dimensions ...............................4
4. EXTERNAL PINS..............................................................................................................5
4.1. Main Board Interface Connectors ..........................................................................................5
4.1.1. Camera Interface and Expansion Connectors...................................................................... 6
4.1.2. Ethernet Interface (CN7: TM11R-5M2-88-LP) ...................................................................... 7
4.1.3. JTAG In-Circuit Emulator Interface (CN1: XG8W-2031) ....................................................... 7
4.1.4. Serial (RS232-C) Interface (CN13: XG8W-1031) ................................................................. 7
4.1.5. Power Supply Connector (CN10: MJ-179P) ......................................................................... 7
4.1.6. CF Card Interface (CN8: M21A-50PD-SF) ........................................................................... 8
4.2. Camera Board Interface Connectors .....................................................................................9
4.2.1. Main Board Interfaces .......................................................................................................... 9
4.2.2. Serial (RS232-C) Interface (CN6: XG8W-1031) ................................................................. 10
4.2.3. Audio Interface Connectors (CN7 to CN10: A2PA-3PGG).................................................. 11
4.2.4. Camera Module Connectors (CN2, CN4, and CN5) ........................................................... 11
5. FUNCTIONAL DESCRIPTION........................................................................................12
5.1. Mode Select DIP Switches (SW6) .......................................................................................13
5.2. GPIOB DIP Switches (SW10) ..............................................................................................13
5.3. Hardware Reset Switch (SW3) ............................................................................................14
5.4. CF Card CFOE#/CFRST Select Switch (SW8)....................................................................14
5.5. Memory Chip Select Switch (SW5)......................................................................................14
5.6. Connection Switch for nSRST from JTAG In-Circuit Emulator (SW2) .................................14
5.7. External Memory Control Signal Monitor Connector (CN9) .................................................15
5.8. External Memory Expansion SOLDER_JP (JP1-JP3) .........................................................15
5.9. CF Card Interface SOLDER_JP (JP6, JP7).........................................................................15
6. SPECIFICATIONS...........................................................................................................16
6.1. Power Supplies....................................................................................................................16
6.2. Current Consumption...........................................................................................................17
6.3. Debugging Environment ......................................................................................................18
7. IMPORTANT USAGE NOTES ........................................................................................26

Contents
ii EPSON S1S65010
Evaluation Board Technical Manual (Rev. 1.1e)
8. PARTS LISTS..................................................................................................................27
8.1. Main Board Parts................................................................................................................. 27
8.2. Camera Board Parts............................................................................................................ 28
9. MISCELLANEOUS..........................................................................................................29

1. OVERVIEW
S1S65010 EPSON 1
Evaluation Board Technical Manual (Rev. 1.1e)
1. OVERVIEW
This product, the S1S65010 Evaluation Board Kit, is for quickly building a network-accessible camera based on the
Seiko Epson S1S65010 network camera chip. It consists of two main components: a main board (Product Number
S5U1S65K01H0100) containing the S1S65010 and other major ICs and a camera board (Product Number
S5U1S65K01H1100) for mounting a camera module.
2. COMPONENTS
2.1. Main Board (Product Number S5U1S65K01H0100)
Network camera IC: S1S65010
Flash EEPROM: 4 MB (Toshiba TC58FVM5B2ATG65)
SRAM: 2 MB (Toshiba TC55VBM416AFTN)
SDRAM: 16 MB (Micron MT48LC8M16A2TG-75)
Ethernet interface: Support 10/100BaseT via MII
RJ45 connector ↔TG110-LC55NC ↔ICS1893BF
JTAG debugging interface: 20-pin connector for in-circuit emulator or other debugger
Camera board interface: 16/40-pin connector for camera board
I2C: Part of the camera board interface connector is used for camera control.
It is also connected to a serial EEPROM (BR24L56RFVM-W).
I2S: Part of the camera board interface connector is used for connecting a
monaural codec IC.
GPIO: Part of the camera board interface connector is used for evaluating
GPIO operation.
Serial interface: 10-pin RS232-C connector
Power supply voltage: 5 V ±10%
2.2. Camera Board (Product Number S5U1S65K01H1100)
This board provides connectors for the following three CMOS camera modules.
•OmniVision OV7640 EAA (or OV7648 EAA)
•Hynix HV7131GP (HYCA3-L01)
•Fuji Film Microdevices SA2101A
Note: This board does not support simultaneous connection of multiple camera modules. The
developer must pick one of the above three.
This board includes a monaural codec IC, an AK4536 with built-in microphone and speaker amplifiers.

2. COMPONENTS
2EPSON S1S65010
Evaluation Board Technical Manual (Rev. 1.1e)
2.3. Block Diagram
The following figure gives block diagram for both the main and camera boards in this evaluation kit.
Flash
ROM
（Max 4 MB )
SDRAM
(16 MB) SRAM （Max 2 MB)
S1S65010 10/100 PHY Pulse
Trans
２３２
Driver
Serial
EEPROM
DIP-SW
Data
Bus
Buffer
３２KHｚ
OSC 25MKHｚ
OSC
CF Card
Connector
RJ-45
Connector
JTAG I/F
２３２
Port
CMOS
Camera Module Note: The developer must pick
one of the three supported
camera modules.
Camera Board
Main Board
CMOS
Camera Module
CMOS
Camera Module
MINI JACK
MINI JACK
MINI JACK
MINI JACK
Monoural
Codec
Figure 2.1. Block Diagram

3. MECHANICAL SPECIFICATIONS
S1S65010 EPSON 3
Evaluation Board Technical Manual (Rev. 1.1e)
3. MECHANICAL SPECIFICATIONS
The next two Figures show the layout and dimensions of the main and camera boards, respectively.
3.1. Main Board (Product Number S5U1S65K01H0100) Layout and Dimensions
Screwhole
4-φ3.5
Top View
Bottom View
Space for
applying seal with
serial number
C
L
6
1228.64
12
33
CN7
T1
S1S65010
U4
1
ICS1893BF
Disk On Chip
（OPTION）
1
U12
CN9
U8
U7
U9
MT48LC8M16A2TG- 75
1
SRAM
TC58FVM5
B2AFT65
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
４７
１６V
４７
１６V
１０
１６V １０ １６V
1
SW5
SW8
①
①②
1
LED3 LED4
CN11
CN10
1
2
15
16
1
2
39
40
CN12
CN5CN3
SW4 SW7
CN1
1 2
19 20
SW2
SW3
CN6
U7
CN13
1 2
9
10
SW10MODE INIT SW6
212
11
1 2 3 4 5 6
SW1
U8
SW9
T1
CN7
U12
CN4
CN2 U4
U9
HALO
TG110-LC55N2
34.4
S1S65K/61K
Network Borad2
U6
U13
PST600
TC58FVM5B2AF
T65
U13
TC74VCX16245FT
SG-3030JF
32.768KHz
SG-645SCG
25MHz
uPC2933T
MM1572H
LT196
2
SP3232
ECY
TC7W14
TC4S30F
TC4S71F TC7MH574
FK
TC74VHC
157F
U3
U10
U11
JP5
JP4
U18
U2
U1
U15 GND
INOUT
U17
JP2
JP3
JP1
JP7 JP6
50
CN8
U14
U5
U16
X1
X2
1
K-624-01
22
30.5
75
95
68
88
BR24L
16
FVM-W
②
Main Board Layout
and
Dimensions
Figure 3.1. Main Board (Product Number S5U1S65K01H0100) Layout and Dimensions

3. MECHANICAL SPECIFICATIONS
4EPSON S1S65010
Evaluation Board Technical Manual (Rev. 1.1e)
3.2. Camera Board (Product Number S5U1S65K01H1100) Layout and Dimensions
Camera Board
Layout and
Dimensions
Top View
Bottom View
39
40
CN3
1
２
15 1
CN１
16 ２
1
19
2
20
CN２
CN５
1
23
22
44
CN６
１
２
９
１０
CN７
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
1 2
１０
１６V １０ １６V
１０
１６V １０ １６V
１０
１６V
１０
１６V
１０
１６V １０
１６V
１０
１６V
１０
１６V
２．２ １６V
１０
１６V
１０
１６V
1
1
SG-645SCG
25MHz
SP3232EC
Y
TC7W14
MM1572H MM1572H
MM1572H
MM1572H
SW5
TC74VHC
05FT
LT1962
CN8
CN9
CN10
SA2101A
HYCA3-L01RS232C
CAMERA EXT
CF CTRL
LED1
U5
U4
U6
U7
U3
U2
SW1
X1
U9
U1
SW3 SW4
SW2
C
L
56.0
38.0
65
.
0
18.85
95.0
58.0
5.2
12.028.64
12.0
88.0
20.0
Screw hole
4-φ3.5
9.8
12.0 12.0 12.018.5
10.5
CN4
1
2
31
32
LINE-OUT
SP-OUT
LINE-IN
MIC
S1S65K/61K
Network Borad
Ｋ−６２５−０１
for connecting an OmniVision
camera module
52.0
Figure 3.2. Camera Board (Product Number S5U1S65K01H1100) Layout and Dimensions

4. EXTERNAL PINS
S1S65010 EPSON 5
Evaluation Board Technical Manual (Rev. 1.1e)
4. EXTERNAL PINS
4.1. Main Board Interface Connectors
The following Figure showsthe locations of the externalinterface connectors on the mainboard. TheTables in
the following six subsections list their pin assignments.
4
2
6
1
5
73
CN7
T1
S1S65010
U4
1
ICS1893BF
DiskOnCh ip
（OPTION）
1
U12
CN9
U8
U7
U9
MT48LC8M16A2TG-75
1
SRAM
TC58FVM5
B2AFT65
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
４７
１６V
４７
１６V
１０
１６V
１０
１６V
1
SW5
SW8
①②
①②
1
LED3 LED4
CN11
CN10
1
2
15
16
1
2
39
40
CN12
CN5CN3
SW4 SW7
CN1
1 2
19 20
SW2
SW3
CN6
U7
CN13
1 2
9
10
SW10MODE INIT SW6
212
11
1 2 3 4 5 6
SW1
U8
SW9
T1
CN7
U12
CN4
CN2
U4
U9
HALO
TG110-LC55N2
S1S65K/61K
NetworkBorad2
Figure 4.1. Main Board Layout

4. EXTERNAL PINS
6EPSON S1S65010
Evaluation Board Technical Manual (Rev. 1.1e)
4.1.1. Camera Interface and Expansion Connectors
(1) GPIOD and GPIOE or CF control/monitor (CN11: XG8W-1631) (1) in Figure 4.1
Pin
Number Function Pin Number Function
1 VDD (5 V) 2 VDD (5 V)
3 CFCE2# (GPIOD2) 4 CFCE1# (GPIOD3)
5 CFIORD# (GPIOE0) 6 CFIOWR# (GPIOE1)
7 CFIREQ (GPIOE4) 8 CFRST# (GPIOE3)
9 CFWAIT# (GPIOE2) 10 CFSTSCHG# (GPIOE5)
11 CFDEN# (GPIOE6) 12 CFDIR# (GPIOE7)
13 RESET# 14 GND
15 GND 16 GND
If the user application system does not use CF cards, the CF card interface lines are available for use as
GPIOD[3:2] and GPIOE[7:0], as indicated with parentheses in the above Table.
(2) Camera interface and expansion connector (CN12: XG8W-4031) (2) in Figure 4.1
Pin
Number Function Pin Number Function
1 GND 2 GND
3 CAMDATA0 4 CAMDATA1
5 CAMDATA2 6 CAMDATA3
7 CAMDATA4 8 CAMDATA5
9 CAMDATA6 10 CAMDATA7
11 CMCLKOUT 12 CMCLKIN
13 CMVREF 14 CMHREF
15 CAMVDD 16 CAMVDD
17 I2C_SDA 18 I2C_SCL
19 3.3V 20 3.3V
21 GPIOA0 22 GPIOA1
23 GPIOA2 (TXD1/SPI_SS) 24 GPIOA3 (RXD1/SPI_SCLK)
25 GPIOA4 (SPI_MISO) 26 GPIOA5 (SPI_MOSI)
27 GPIOA6 28 GPIOA7
29 GPIOB0 (I2S0_WS) 30 GPIOB1 (I2S0_SCK)
31 GPIOB2 (I2S0_SD) 32 GPIOB3 (I2S1_SD)
33 GPIOB4 (Timer 1 out) 34 GPIOB5
35 GPIOB6 36 GPIOB7
37 GPIOD0 38 GPIOD1
39 GND 40 GND

4. EXTERNAL PINS
S1S65010 EPSON 7
Evaluation Board Technical Manual (Rev. 1.1e)
4.1.2. Ethernet Interface (CN7: TM11R-5M2-88-LP) (3) in Figure 4.1
Pin Number Function Pin Number Function
1 TPTXDP 2 TPTXDN
3 TPRXDP 4 NC
5 NC 6 TPRXDN
7 NC 8 NC
4.1.3. JTAG In-Circuit Emulator Interface (CN1: XG8W-2031)
(4) in Figure 4.1
Pin Number Function Pin Number Function
1 3.3 V 2 3.3 V
3 nTRST 4 GND
5 TDI 6 GND
7 TMS 8 GND
9 TCK 10 GND
11 GND 12 GND
13 TDO 14 GND
15 nSRST 16 GND
17 NC 18 GND
19 NC 20 GND
4.1.4. Serial (RS232-C) Interface (CN13: XG8W-1031) (5) in Figure 4.1
Pin Number Function Pin Number Function
1 NC 2 RXD
3 TXD 4 NC
5 GND 6 NC
7 RTS 8 CTS
9 NC 10 NC
This layout matches that used by such PC motherboard manufacturers as ASUS and GIGABYTE.
4.1.5. Power Supply Connector (CN10: MJ-179P) (6) in Figure 4.1
This is for connecting the AC power supply adapter included with the kit.

4. EXTERNAL PINS
8EPSON S1S65010
Evaluation Board Technical Manual (Rev. 1.1e)
4.1.6. CF Card Interface (CN8: M21A-50PD-SF) (7) in Figure 4.1
Pin Number Function Pin Number Function
1 GND 2 D3 (CF_D3)
3 D4 (CF_D4) 4 D5 (CF_D5)
5 D6 (CF_D6) 6 D7 (CF_D7)
7 CE1# (CFCE1#) 8 A10 (MA10)
9 OE# (CFOE#) 10 A9 (MA9)
11 A8 (MA8) 12 A7 (MA7)
13 VCC1 (3.3V) 14 A6 (MA6)
15 A5 (MA5) 16 A4 (MA4)
17 A3 (MA3) 18 A2 (MA2)
19 A1 (MA1) 20 A0 (MA0)
21 D0 (CF_D0) 22 D1 (CF_D1)
23 D2 (CF_D2) 24 WP (NC)
25 CD2# (NC) 26 CD1# (NC)
27 D11 (CF_D11) 28 D12 (CF_D12)
29 D13 (CF_D13) 30 D14 (CF_D14)
31 D15 (CF_D15) 32 CE2# (CFCE2#)
33 VS1# (NC) 34 IORD#
(CFIORD#)
35 IOWR#
(CFIOWR#) 36 WE# (MWE0#)
37 RDY/BSY
(CFIREQ) 38 VCC1 (3.3V)
39 CSEL# (CSEL#) 40 VS2# (NC)
41 RESET
(CFRST_CN) 42 WAIT#
(CFWAIT#)
43 INPACK# (NC) 44 REG# (REG#)
45 BVD2
(BVD2/DASP) 46 BVD1
(CFSTSCHG#)
47 D8 (CF_D8) 48 D9 (CF_D9)
49 D10 (CD_D10) 50 GND
The following pins are nonfunctional on this evaluation board because the S1S65010 does not support them:
VS1#, VS2#, WP, CD1#, CD2#, INPACK#, and BVD2.

4. EXTERNAL PINS
S1S65010 EPSON 9
Evaluation Board Technical Manual (Rev. 1.1e)
4.2. Camera Board Interface Connectors
The following Figure shows the locations of the external interface connectors on the camera board. The Tables
in the following four subsections list their pin assignments.
8
5
6
7
1
4
10
39
40
CN3
1
２
15 1
CN１
16 ２
119
2
20
CN２
CN５
1
23
22
44
CN ６
１
２
９
１０
CN ７
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2
１０
１６V
１０
１６V
１０
１６V １０ １６V
１０
１６V
１０ １６ V
１０ １６V
１０ １６V １０ １６ V
１０
１６V
２． ２ １６ V
１０
１６V
１０ １６ V
1
1
SG-645SCG
25MHz
SP3232
ECY
TC7W14
MM1572H MM1572H
MM1572H
MM1572H
SW5
TC74VHC
05FT
LT196
2
CN8
CN9
CN10
SA2101A
HYCA3- L01RS232C
CAMERA EXT
CF CTRL
LED1
U5
U4
U6
U7
U3
U2
SW1
X1
U9
U1
SW3 SW4
SW2
2
3
9
Figure 4.2. Camera Board Layout
4.2.1. Main Board Interfaces
(1) CF control/monitor (CN3: HIF3H-16DB-2.54S) (1) in Figure 4.2
Pin Number Function Pin Number Function
1 5 V 2 5 V
3 NC 4 NC
5 NC 6 NC
7 NC 8 NC
9 NC 10 NC
11 NC 12 NC
13 RESET# 14 GND
15 GND 16 GND

4. EXTERNAL PINS
10 EPSON S1S65010
Evaluation Board Technical Manual (Rev. 1.1e)
(2) Camera interface and expansion connector (CN1: HIF3H-40DB-2.54DS)
(2) in Figure 4.2
Pin Number Function Pin Number Function
1 GND 2 GND
3 CAMDATA0 4 CAMDATA1
5 CAMDATA2 6 CAMDATA3
7 CAMDATA4 8 CAMDATA5
9 CAMDATA6 10 CAMDATA7
11 CMCLKOUT 12 CMCLKIN
13 CMVREF 14 CMHREF
15 CAMVDD 16 CAMVDD
17 I2C_SDA 18 I2C_SCL
19 3.3V 20 3.3V
21 GPIOA0 22 GPIOA1
23 GPIOA2
(TXD1/SPI_SS) 24 GPIOA3 (RXD1/SPI_SCLK)
25 GPIOA4
(SPI_MISO) 26 GPIOA5 (SPI_MOSI)
27 GPIOA6 28 GPIOA7
29 GPIOB0
(I2S0_WS) 30 GPIOB1 (I2S0_SCK)
31 GPIOB2
(I2S0_SD) 32 GPIOB3 (I2S1_SD)
33 GPIOB4
(Timer 1 out) 34 GPIOB5
35 GPIOB6 36 GPIOB7
37 GPIOD0 38 GPIOD1
39 GND 40 GND
4.2.2. Serial (RS232-C) Interface (CN6: XG8W-1031) (3) in Figure 4.2
Pin Number Function Pin Number Function
1 NC 2 RXD
3 TXD 4 NC
5 GND 6 NC
7 RTS 8 CTS
9 NC 10 NC
This layout matches that used by such PC motherboard manufacturers as ASUS and GIGABYTE.

4. EXTERNAL PINS
S1S65010 EPSON 11
Evaluation Board Technical Manual (Rev. 1.1e)
4.2.3. Audio Interface Connectors (CN7 to CN10: A2PA-3PGG)
These are for a microphone, a speaker, and line I/O.
(4) to (7) in Figure 4.2
Connector Function Note
CN7 Microphone input
CN8 Line input
CN9 Line output
CN10 Speaker output
4.2.4. Camera Module Connectors (CN2, CN4, and CN5)
This board provides three (mutually exclusive) connectors for connecting a CMOS camera module.
(8) to (10) in Figure 4.2
Location Function Product Number
CN2 HV7131GP (HYCA3-L01) 245602-020-000-829
CN4 OV7640 EAA (or OV7648 EAA) 803-93-032-10-001
CN5 SA2101A A5-44DA-2DS

5. FUNCTIONAL DESCRIPTION
12 EPSON S1S65010
Evaluation Board Technical Manual (Rev. 1.1e)
5. FUNCTIONAL DESCRIPTION
Figures 5.1 and 5.2 show component locations on both sides of the main board. The following nine subsections
describe their functions.
CN7
T1
S1S65010 U4
1
ICS1893BF
DiskOnChip
（OPTION）
1
U12
CN9
U8
U7
U9
MT48LC8M16A2TG-75
1
SRAM
TC58FVM5
B2AFT65
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
４７
１６V
４７
１６V
１０
１６V
１０
１６V
1
SW5
SW8
①②
①②
1
LED3 LED4
CN11
CN10
1
2
15
16
1
2
39
40
CN12
CN5CN3
SW4 SW7
CN1
1 2
19 20
SW2
SW3
CN6
U7
CN13
1 2
9
10
SW10MODE INIT SW6
212
11
1 2 3 4 5 6
SW1
U8
SW9
T1
CN7
U12
CN4
CN2 U4
U9
HALO
TG110-LC55N2
S1S65K/61K
NetworkBorad2 6
4
3 2 1
75
Figure 5.1. Main Board (Top View)
U6U13
PST600
TC58FVM5B2AF
T65
U13
TC74VCX16245FT
SG-3030JF 32.768KHz
SG-645SCG
25MHz
uPC2933T
MM1572H
LT196
2
SP3232
ECY
TC7W14
TC4S30F
TC4S71F TC7MH574
FK
BR24L
16
FVM-W
TC74VHC
157F
U3
U10
U11
JP5
JP4
U18
U2
U1
U15 GND
INOUT
U17
JP2
JP3
JP1
JP7 JP6
50
CN8
U14
U5
U16
X1
X2
1
K-624-01
12 11 10 9 8
Figure 5.2. Main Board (Bottom View)

5. FUNCTIONAL DESCRIPTION
S1S65010 EPSON 13
Evaluation Board Technical Manual (Rev. 1.1e)
5.1. Mode Select DIP Switches (SW6) (1) in Figure 5.1
These switches (SW6) on the main board specify the system configuration inputs MODESEL[7:0] described
in Section 4.1 of the S1S65010 Technical Manual. The following Table summarizes their function.
Table 5.1
Function
Pin
Number Symbol Abbreviation 0 (OFF) 1 (ON) Note
SW6
1-16 SW6 1 MD0 (MODESEL0) 32 kHz mode Reserved (for testing)
SW6
2-15 SW6 2 MD1 (MODESEL1)
Insert crystal oscillator
stabilization interval (3
seconds)
Skip stabilization interval
(10 ms)
SW6
3-14 SW6 3 MD2 (MODESEL2) Normal operation Reserved (for testing)
SW6
4-13 SW6 4 MD3 (MODESEL3) Reserved (must be 0)
SW6
5-12 SW6 5 MD4 (MODESEL4) SW normal operation Return switches to factory defaults See Note.
SW6
6-11 SW6 6 MD5 (MODESEL5) Application mode Monitor mode
SW6
7-10 SW6 7 MD6 (MODESEL6) Wired LAN connection Wireless LAN connection
SW6
8-9 SW6 8 MD7 (MODESEL7) User setting User setting
Note: This evaluation board appropriates this S1S65010 user setting input for use in returning switches to
their factory default settings.
5.2. GPIOB DIP Switches (SW10) (2) in Figure 5.1
These switches (SW10) specify input to the corresponding GPIOB port pins: “1” for the OFF position and
“0” for ON.
Table 5.2
Function
Pin
Number Symbol Abbreviation 0 (OFF) 1 (ON) Note
SW10
1-16 SW10 1 GPIOB0 Logical “1” input Logical “0” input
SW10
2-15 SW10 2 GPIOB1 Logical “1” input Logical “0” input
SW10
3-14 SW10 3 GPIOB2 Logical “1” input Logical “0” input
SW10
4-13 SW10 4 GPIOB3 Logical “1” input Logical “0” input
SW10
5-12 SW10 5 GPIOB4 Logical “1” input Logical “0” input
SW10
6-11 SW10 6 GPIOB5 Logical “1” input Logical “0” input
SW10
7-10 SW10 7 GPIOB6 Logical “1” input Logical “0” input
SW10
8-9 SW10 8 GPIOB7 Logical “1” input Logical “0” input