Ercol Teramo 2686 User manual

ercol
Thank you for purchasing this teramo 2 door wardrobe. Please read the instructions carefully before use to en-
sure safe and satisfactory operation of this product.
Pre-assembly preparation
Please ensure instructions are read in full before attempting to assemble this product
Necessary Tools
This item is HEAVY
Please check the pack contents before attempting to assemble this product. A full checklist of components
is given in this leaflet. If any components are missing, please contact the retailer from whom you bought
this product.
This product is HEAVY, it should be assembled as near as possible to the point of use. TAKE CARE
WHEN LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 30 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG
CHILDREN.
teramo 2686 2 door wardrobe

Fittings and parts checklist
A Top panel x 1 H 25mm Screws x 16
B LH side panel x 1 I 30mm Screws x 4
C RH side panel x 1 J Brackets x 2
D Left & Right doors x 2
K
Strap x 1
E Back panel x 1
L
Screws x 1
F Drawer box unit x 1 M Wedge x 2
G Hanging rail x 1
N&O
M6*35 Bolt x 14
Allen key x 1

Step by step assembly instructions
1. Take the drawer out of the drawer box unit as shown below.
2. Attach the side panels B & C to the drawer box unit, making sure the 4 dowels locate squarely into
the side panels. Using M6*35 bolt 8pcs , attach the side panels B & C through the inside holes
of the drawer box unit, as shown below.

3. Locate the top panel A into the dowels on the tops of the side panels B & C and secure using the 6pcs
4. To increase the overall strength, Using 4 of the 30mm screws (I) attach the side panel rails front and
back to the top of the wardrobe through the pre drilled holes provided, see below. Attach the door
M6*35 bolt.
panels onto the side panels as shown below.

5. Using the 25mm screws H (16), fix the back panel to the rear of the wardrobe as shown.
6. Put the hanging rail, G into the hanging rail supports inside the wardrobe, and put the drawer into the
the drawer box.

Wall fixing - if in doubt seek professional advice
Wood
If fixing to wood
make sure that it
isn’t chipboard as
screws can easily pull
away from the core
structure
Brick or Masonry
Use an appropriate
wall plug provided you
are sure your wall is
sound
Cavity wall
Special toggle
wall plugs are
needed. Seek
expert advice
7. Screw one of the brackets onto the top of the wardrobe in the middle of the back, see below.
Position the wardrobe against the wall where you want it to go, place the second bracket
onto the wall above the one fixed to the wardrobe and mark where the hole come on the wall. Move
the wardrobe away from the wall.
8. Attach the wall bracket using screws suitable for your type of wall, see Wall fixings above.
9. Place the wardrobe back against the wall so the two brackets match up and tie them together with
the plastic strap provided. The plates need not match exactly, but the plastic tie must go through
each plate. Close the strap, but do not over tighten it. See diagrams below.

10. If the wardrobe is not level on your floor, use the wedges provided. Snap them off so they do not
protrude out from the wardrobes legs. You can also snap them lengthways.
11. Check that the doors are aligned correctly. If necessary adjust the door hinges as shown below
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
Ercol Furniture Ltd, Summerleys Road, Princes Risborough, Buckinghamshire. HP27 9PX www.ercol.com