ETEKCITY ESF24 User manual

1
Smart Fitness Scale
Model: ESF24 Series
User Manual
Questions or Concerns?
Mon – Fri, 9:00 am – 5:00 pm PST/PDT
[e-mail] • [phone]

2
Table of Contents
Package Contents
Specications
Safety Information
Function Diagram
Display Diagram
Before First Use
VeSync App Setup
Using the Smart Scale
Maintenance
Common Display Codes
Troubleshooting
FCC Statement
Limited One-Year Warranty
Customer Support
3
3
4
6
7
8
9
12
14
16
17
20
21
23

3
1 x Smart Fitness Scale
3 x 1.5V AAA Batteries (Pre-Installed)
1 x Quick Start Guide
Specifications
Package Contents
Weight Capacity 400 lb / 180 kg / 28 st
Increments 0.2 lb / 0.05 kg
Weight Units lb / kg / st
Platform Tempered glass
Battery 3 x 1.5V AAA batteries
Auto-Off 30 seconds
Dimensions 11.8 x 11.8 x 1 in / 30 x 30 x 2.5 cm
Operating System iOS®9.0+ or Android™ 5.0+

4
Safety Information
• This scale should not be used to diagnose or treat any medical
condition.
• Scale data should not be used as a substitute for medical advice
from a healthcare professional.
• This scale uses a harmless electrical current to measure body fat.
Consult a healthcare professional before using the smart scale if
you use medical electronic equipment such as a pacemaker.
• Check the scale before using. Do not use the scale if it is damaged
in any way.
• Do not strike or hit the scale. Do not use the scale if the glass is
cracked or broken. Due to the nature of tempered glass, the glass
will shatter if there is even a slight crack. If you see a crack, contact
Customer Support immediately (page 23).
Please read and follow all instructions and safety guidelines
in this manual.
READ AND SAVE THESE INSTRUCTIONS
Medical
General Use

5
• Do not mix new and old batteries.
• If the scale is not in use for a long period of time, remove
the batteries to extend the lifetime of the scale.
Batteries
• The glass platform is slippery when wet. Always make sure the
platform and your feet are dry before stepping on for measurement.
• Place the scale on a hard, at surface to avoid tipping.
• To weigh safely and accurately, stand with your feet shoulder-
width apart while on the scale. Do not stand on the edge of the
scale or jump on the scale.
• Avoid standing on the scale for a long period of time, or when
you are not weighing yourself.
• Do not overload the scale. Maximum weight capacity is 400 lb /
180 kg / 28 st.
• Keep the scale in a cool area with low humidity. Keep the
scale away from heat sources, such as ovens or heaters.
Avoid temperature uctuations. Store the scale in a horizontal
position, not vertical.
• Handle with care. Not for commercial use. Household use only.

6
Function Diagram
A. Weighing Platform
B. Display
C. Anti-Skid Padding
D. Battery Compartment
BA
D
C

7
Display Diagram
A. Weight Measurement
B. Bluetooth®Icon
C. Weight Units
A
B
C

8
Before First Use
1. Open the battery compartment on the underside of the
scale. Remove the included AAA batteries.
2. Remove the plastic insulator strip from the battery
compartment.
3. Replace the batteries. Follow the guidelines in the battery
compartment to match the +and –terminals.
Slide
1.5v - AAA
1.5v - AAA
1.5v - AAA
1.5V - AAA
1.5V - AAA
1.5V - AAA
Slide

9
VeSync App Setup
1. To download the VeSync app, scan the QR code or
search “VeSync” in the Apple App Store®or Google
Play Store.
Note: Due to app updates and improvements, the VeSync app may be
slightly different than shown in the manual. In case of any differences,
follow the in-app instructions.
Note:
• This scale uses the VeSync app, not the VeSyncFit app.
• For Android users, you may need to select “Allow” to use VeSync.

10
2. Open the VeSync app. If you already have an account,
tap Log In. To create a new account, tap Sign Up.
Note: You must create your own VeSync account to use third-party
services and products. These will not work with a guest account. With a
VeSync account, you can also allow your family and friends to use your
smart tness scale.
Note: You can change the name and icon at any time in the smart
tness scale settings.
3. Make sure the scale is fully charged.
4. Make sure your phone has Bluetooth®turned on.
5. Tap +in the VeSync app and select your smart
tness scale.
6. Follow the in-app instructions to connect to your
smart tness scale.

11
Creating a User
If you are a new user, you will need to enter physical
information before weighing yourself for the rst time
so the scale can calculate your body metrics. Follow
the in-app instructions to create a user.
Note:
• Entering inaccurate information will make the scale’s
measurements less accurate.
• If you don’t identify with the available gender options,
or are unsure, pick the option that you think best
physically matches you. This choice is used for physical
measurements, such as body fat percentages.

12
Using the Smart Scale
Note:
• To switch between pounds (lb), stone (st), and kilograms (kg),
open the VeSync app and select the weight unit in the Device
Settings menu.
• To see measurements besides weight, you must connect the
scale to the VeSync app (see page 9).
• If you are pregnant, scale measurements will not be accurate.
1. Place the scale on a hard, at surface (not a carpet or
mat). [Figure 1.1]
Note: Placing on carpet may cause inaccurate measurements or tipping.
[Figure 1.1]

13
2. Make sure your feet are dry. Place bare feet on the scale’s
conductive areas. Step onto the scale. The scale will
automatically turn on and start measuring your weight.
3. Continue standing on the scale until the digits on the
display ash 2 times, showing your nal measurement.
[Figure 1.2] If your smart scale is connected to the
VeSync app, additional results (such as BMI, body fat,
etc) will show in the app.
[Figure 1.2]

14
Maintenance
Calibrating the Smart Scale
If the scale has been moved or ipped upside down, it
must be calibrated to ensure accurate results.
1. Place the scale on a hard, at surface.
2. Step on the scale with 1 foot until digits appear on the
display, then step off. [Figure 2.1]
3. The scale will show “ ” while calibrating, then “ ”
when calibration is complete. [Figure 2.2]
[Figure 2.1] [Figure 2.2]

15
Cleaning the Smart Scale
Replacing the Batteries
The display will show “ ” when the batteries need to be
replaced.
1. Open the battery compartment on the underside of
the scale.
2. Remove the old batteries and dispose of them properly.
3. Install 3 new 1.5V AAA batteries, making sure they are
placed under the correct polarity.
4. Replace the battery compartment cover.
• Use a slightly damp cloth to clean the surface of the
scale, followed by a soft, dry cloth to wipe away any
remaining moisture.
• Do not use chemical or abrasive cleaning agents to
clean the scale.
Note: The scale may need to be calibrated after replacing the batteries.

16
Common Display Codes
Wireless Connection No Wireless Connection
Change Battery
OverloadCalibrating

17
Troubleshooting
The scale doesn’t turn on.
• Check if the batteries are properly installed. If using the scale
for the rst time, remove the plastic insulator strip from the
battery compartment.
Information ashes on the display and then disappears.
• The batteries are low and may need to be replaced.
The smart scale doesn’t connect with the VeSync app.
• Make sure your phone’s operating system is running on iOS
9.0+ or Android 5.0+.
• Close and relaunch the VeSync app. Make sure you’re using
the latest version.
• Make sure your phone has Bluetooth turned on. For Android
users, make sure your Location is turned on as well.
• Make sure your scale and phone are within 30 ft / 10 m of
each other.
• Make sure the scale is not currently connected to any other
phone or app.
• Try turning off any VPN apps.

18
My scale will only measure my weight, not my body fat or other metrics.
• Set up your smart scale in the VeSync app. Your weight will show on
the scale display, and more results will show on the app.
• If you’re wearing shoes or socks, the scale cannot measure health
metrics such as body fat. Step on the scale with bare feet. [Figure 3.1]
• Make sure to place your feet on the scale’s conductive areas.
[Figure 3.2]
Note: If the scale has errors on the display, will not turn off automatically,
or has a problem not listed here, try removing the batteries for 3 seconds,
then replacing them.
[Figure 3.1] [Figure 3.2]
Conductive Areas
If you still need help, please contact Customer Support
(page 23).

19
Attributions
iOS is a registered trademark of Cisco Systems, Inc. and/or its afliates in the United
States and certain other countries.
Apple App Store is a trademark of Apple Inc.
Android and Google Play are trademarks of Google LLC.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by Etekcity Corporation is under license.

20
FCC Statement
FCC Radiation Exposure Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that
may cause undesired operation.
Any changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specic operating instructions
for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure
compliance requirements, please follow operation instructions as documented in this
manual. This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter. This equipment should be installed and operated with
a minimum distance of 20 cm between the radiator and your body. The availability of
some specic channels and/or operational frequency bands are country dependent
and are rmware programmed at the factory to match the intended destination. The
rmware setting is not accessible by the end user.