Evco c-pro 3 OEM User manual

EVCO | 06.08.2021 | AZ | 1114CP3OEE104
c-pro 3 OEM
Hardware manual:
Programmable controls
|Flexible, modular, expandable
|21 inputs and outputs
|Variety of communications ports
|Models with management of Pulse electronic
expansion valves
|Models with integrates user interface or in blind
version
|Standard 8 DIN module format
|OEM oriented
Refrigeration
units Chiller Display cabinets
Applications

EVCO | 06.08.2021 | AZ | 2114CP3OEE104
c-pro 3 OEM - Hardware manual
IMPORTANT
Read this document thoroughly before installation and before use of the device and follow all recommendations;
keep this document with the device for future consultation.
Only use the device in the way described in this document; do not use the same as a safety device
CONSIDER THE ENVIRONMENT
Please read careffully and save this document
DISPOSAL
The device must be disposed of in compliance with local standards regarding the collection of electric and electronic
equipment

EVCO | 06.08.2021 | AZ | 3114CP3OEE104
c-pro 3 OEM - Hardware manual
Index
| Introduction 6
| Purchasing codes 7
|Open frame version 7
| Purchasing codes 8
|Plastic housing version (blind/LCD) 8
| Dimensions 9
|Open frame version 9
|Plastic housing version (blind) 9
|Plastic housing version (LCD) 9
| Installation 10
|Open frame version 10
|Plastic housing version (blind/LCD) 10
| Electrical connections 11
|Connectors description 11
|Open frame version 11
|Plastic housing version (blind/LCD) 13
|Electrical connection 15
|Open frame version 15
|Termination of the RS-485 MODBUS and CAN networks. Polarisation of RS-485 MODBUS network 15
|Plastic housing version (blind/LCD) 16
|Termination of the RS-485 MODBUS and CAN networks. Polarisation of RS-485 MODBUS network 16
| User interface version conguration 17
|Keyboard 17
|Key description 17
|Switching ON/OFF the device 17
|Accessing the procedure 17
|Accessing the menu 17
|Parameters conguration 17
|Password 17

EVCO | 06.08.2021 | AZ | 4114CP3OEE104
c-pro 3 OEM - Hardware manual
| Housing and blind version conguration 18
|Through a controller with user interface 18
|Conguration 18
|Switching ON/OFF the device 18
|Accessing the procedure from c-pro 3 OEM LCD 18
|CAN node address setting 18
|Accessing the menu from c-pro 3 OEM LCD 19
|Parameters conguration from c-pro 3 OEM LCD 19
|Password 19
|Through a remote user interface 20
|Conguration 20
|Key description 20
|Switching ON/OFF the device from EPJgraph 20
|Accessing the procedure from EPJgraph 20
|Password 20
|CAN node address setting 21
|Accessing the menu from EPJgraph 21
|Parameters conguration from EPJgraph 21
| LED 22
|LED description 22
| Settings menu 23
|Keys description and parameters settings 23
|Menu “Info” keys 23
|Menu “Info” parameters 23
|Menu “Languages” keys 24
|Menu “Languages” parameters 24
|Menu “Parameters” keys 25
|Menu “Parameters (1)” parameters 25
|Menu “Parameters (2)” parameters 26
|Menu “Networks” keys 27
|Menu “Networks” - Submenu “CAN Bus” parameters 27
|Menu “Networks” - Submenu “UART1” parameters 28
|Menu “Networks” - Submenu “UART2” parameters 29
|Menu “Networks” - Submenu “USB” parameters 29
|Menu “Password” keys 30
|Menu “Password” parameters 30
|Menu “Backup/Restore” keys 31
|Menu “Backup/Restore” parameters 31

EVCO | 06.08.2021 | AZ | 5114CP3OEE104
c-pro 3 OEM - Hardware manual
| Accessories 32
|Connection cables 32
|0810500018/0810500020 32
|USB ash drive 32
|EVUSB4096M 32
|RS-485/USB serial interface 32
|EVIF20SUXI 32
|INTRABUS/RS-485 serial interface 32
|EVIF22ISX 32
|Phase cutting speed regulator 33
|EVDFAN1 33
|Connection kit 33
|CJAV45 33
| Technical data 34

EVCO | 06.08.2021 | AZ | 6114CP3OEE104
c-pro 3 OEM - Hardware manual
Introduction
c-pro 3 OEM is a range of programmable controllers in 8-DIN
modules, open-board or with housing (blind or with built-in LCD
display). It has numerous inputs and outputs (up to 21) and an
enhanced memory capacity to meet the management needs of the
HVAC/R sector and OEM companies in particular. The models with
Pulse outputs, for example, can be used to control multiplexed
cabinets.
Thanks to the INTRABUS protocol, advantageous point-to-point
solutions can be used, including the possibility of connecting to
remote LED (Vled 3) or LCD (EVJ LCD) user interfaces.
The CAN protocol makes it possible to increase the number of c-pro
3 OEM inputs/outputs by adding an expansion and to be integrated
with the entire range of c-pro 3 controllers and displays.
The MODBUS RTU option, used with an external interface, is always
available in both master and slave modes. Those models supplied
with the RS-485 enable two MODBUS protocols to be used at the
same time.
The application software can be designed in a simple, intuitive and
portable way thanks to the UNI-PRO 3 integrated development
environment. The USB port, supplied as standard, makes the
controller easy to program in the development phase and in
debugging and it can be updated using the most common USB ash
drives.

EVCO | 06.08.2021 | AZ | 7114CP3OEE104
c-pro 3 OEM - Hardware manual
Purchasing codes
Open frame version
Purchasing codes description
Features Codes
115... 230 VAC - Open frame version - 8 DIN modules - DIN guide- INTRABUS - CAN - USB EPB90
115... 230 VAC - Open frame version - 8 DIN modules - DIN guide - INTRABUS - RS-485 - CAN - USB - Real Time Clock EPB90R
115... 230 VAC - Open frame version - 8 DIN modules - DIN guide - Digital output Pulse - INTRABUS - RS-485 - CAN -
USB - Real Time Clock EPB90V
The following table shows the available c-pro 3 OEM models, open frame version, and the relative purchasing codes
Features Models
EPB90 EPB90R EPB90V
Power supply
115... 230 VAC •••
Congurable inputs (analogue or digital)
Analogue input (PTC/NTC/Pt 1000) or digital input (dry contact) 444
Analogue input (NTC/0-5 V ratiometric/0-10 V/0-20 mA/4-20 mA) or
digital input (dry contact)
333
Digital inputs
Dry contact and for pulse trains up to 2 KHz 222
High voltage 223
Analogue outputs
0-10 V/PWM 444
Digital outputs (electro-mechanical relays; A res. at 250 VAC)
5 A SPST 444
8 A SPST 111
16 A SPDT 111
Digital outputs (Pulse)
230 VAC max. 30 W 1
User interface
None (open frame) •••
Format
8 DIN modules •••
Installation mode
DIN guide •••
Connections
Screw terminal blocks •••
Type A female USB connector •••
Communication ports
INTRABUS 111
RS-485 MODBUS MASTER/SLAVE 1 1
CAN 111
USB 111
Other Features
Real Time Clock • •
For further informations look at chapter “Technical data”

EVCO | 06.08.2021 | AZ | 8114CP3OEE104
c-pro 3 OEM - Hardware manual
Purchasing codes
Plastic housing version (blind/LCD)
Purchasing codes description
Features Codes
115... 230 VAC - Plastic housing version (blind) - 8 DIN modules - DIN guide - INTRABUS - CAN - USB EPB9BXE
115... 230 VAC - Plastic housing version (blind) - 8 DIN modules - DIN guide - INTRABUS - RS-485 - CAN - USB -
Real Time Clock EPB9BRE
115... 230 VAC - Plastic housing version (blind) - 8 DIN modules - DIN guide - INTRABUS - RS-485 - CAN - USB -
Real Time Clock EPB9BVE
115... 230 VAC - Plastic housing version (LCD) - 8 DIN modules - DIN guide - Digital output Pulse - INTRABUS - RS-485
- CAN - USB - Real Time Clock EPB9DRE
The following table shows the available c-pro 3 OEM models, plastic housing version (blind/LCD), and the relative purchasing
codes
Features Models
EPB9BXE EPB9BRE EPB9BVE EPB9DRE
Power supply
115... 230 VAC ••••
Congurable inputs (analogue or digital)
Analogue input (PTC/NTC/Pt 1000) or digital input (dry contact) 4444
Analogue input (NTC/0-5 V ratiometric/0-10 V/0-20 mA/4-20 mA)
or digital input (dry contact)
3333
Digital inputs
Dry contact and for pulse trains up to 2 KHz 2222
High voltage 2232
Analogue outputs
0-10 V/PWM 4444
Digital outputs (electro-mechanical relays; A res. at 250 VAC)
5 A SPST 4444
8 A SPST 1111
16 A SPDT 1111
Digital outputs (Pulse)
230 VAC max. 30 W 1
User interface
None (blind controller) •••
6 buttons + LCD Display •
Format
8 DIN modules ••••
Installation mode
DIN guide ••••
Connections
Plug-in screw terminal blocks ••••
Type A female USB connector ••••
Communication ports
INTRABUS 1111
RS-485 MODBUS MASTER/SLAVE 111
CAN 1111
USB 1111
Other Features
Real Time Clock •••
For further informations look at chapter “Technical data”

EVCO | 06.08.2021 | AZ | 9
004_c-pro3OEM_Contenitore_DIN_001_0.1_AZ
004_c-pro3OEM_Giorno_DIN_001_0.1_AZ
004_c-pro3OEM_ContenitoreCiec_DIN_001_0.1_AZ
114CP3OEE104
c-pro 3 OEM - Hardware manual
Dimensions
Open frame version
Plastic housing version (LCD)
Plastic housing version (blind)
31 mm (1 1⁄4in)
60 mm (2 3⁄8in)
60 mm (2 3⁄8in)
142 mm (5 9⁄16 in)
142 mm (5 9⁄16 in)
142 mm (5 9⁄16 in)
110 mm (4 5⁄16 in)128 mm (5 1⁄16 in)128 mm (5 1⁄16 in)

EVCO | 06.08.2021 | AZ | 10
008_c-pro3OEM_Giorno_DIN_001_0.1_AZ
008_c-pro3OEM_Contenitore_DIN_001_0.1_AZ
008_c-pro3OEM_Giorno_DIN_001_0.1_AZ
008_c-pro3OEM_Contenitore_DIN_001_0.1_AZ
1
1
3
3
2
2
4
4
114CP3OEE104
c-pro 3 OEM - Hardware manual
Installation
Open frame version
1. To install the device :
–operate as shown in pictures 1 and 2
1. To install the device :
–operate as shown in pictures 1 and 2
1. To uninstall the device:
–operate as shown in pictures 3 and 4
2. To install the device again:
–press down the clip before
1. To uninstall the device:
–rst remove any screw-in removable terminal blocks
mounted in the lower part, then operate as shown in
pictures 3 and 4
2. To install the device again:
–press down the clip before
Plastic housing version (blind/LCD)

EVCO | 06.08.2021 | AZ | 11
002_c-pro3OEM_ConnettoriSchedaGiorno_001_0.1_AZ
c-pro 3 OEM
AO4AO3 AO2 AO1 M9 M8
C1 NO1C2NO2 C3 NO3
M7 M6 M5 M4 M3
C4 NO4C5 NO5
M2 M1 GND 12V
NO6 C6 NC6
ITB GND A+
HV1HV1 HV2 HV2
B- C+ C-
PS PS
5V 21
ON
DIHV5 DIHV5
IN OUT
Pulse - EPB90V
114CP3OEE104
c-pro 3 OEM - Hardware manual
Electrical connections
WARNINGS FOR ELECTRICAL CONNECTIONS
–Use cables of an adequate section for the current running through them
–To reduce any electromagnetic interference connect the power cables as far away as possible from the signal cables
and connect to a CAN, RS-485 MODBUS and INTRABUS networks by using a twisted pair
–If using an electrical or pneumatic screwdriver, adjust the tightening torque
–If the device has been moved from a cold to a warm place, the humidity may have caused condensation to form inside.
Wait about an hour before switching on the power
–Make sure that the supply voltage, electrical frequency and power are within the set limits
–Disconnect the power supply before doing any type of maintenance
–Do not use the device as safety device
–For repairs and for further informations, contact the EVCO sales network; possible returns without label data will not be
accepted
Connectors description
Open frame version
Connector 8
Connector 1 Connector 2 Connector 4
Connector 3 Connector 5
Connector 6
Connector 7
Connector 1
Number Description
C1 K1 digital output common contact
NO1 K1 digital output normally open contact
(5 A res. at 250 VAC)
C2 K2 digital output common contact
NO2 K2 digital output normally open contact
(5 A res. at 250 VAC)
C3 K3 digital output common contact
NO3 K3 digital output normally open contact
(5 A res. at 250 VAC)
Connector 2
Number Description
C4 K4 digital output common contact
NO4 K4 digital output normally open contact
(5 A res. at 250 VAC)
C5 K5 digital output common contact
NO5 K5 digital output normally open contact
(8 A res. at 250 VAC)
Connector 3
Number Description
NO6 K6 digital output normally open contact
(16 A res. at 250 VAC)
C6 K6 digital output common contact
NC6 K6 digital output normally closed contact
Connector 4
Number Description
HV1 DI1 High voltage digital input
HV1 DI1 High voltage digital input
HV2 DI2 High voltage digital input
HV2 DI2 High voltage digital input
Connector 9
Connector 10

EVCO | 06.08.2021 | AZ | 12114CP3OEE104
c-pro 3 OEM - Hardware manual
Connector 7
Number Description
USB USB port, for device programming
Connector 8
Number Description
AO4 Analogue output 4 (for 0-10 V or PWM)
AO3 Analogue output 3 (for 0-10 V or PWM)
AO2 Analogue output 2 (for 0-10 V or PWM)
AO1 Analogue output 1 (for 0-10 V or PWM)
M9 Digital input
(dry contact and for pulse trains up to 2 KHz) DI4
M8 Digital input
(dry contact and for pulse trains up to 2 KHz) DI3
M7
Analogue input
(for PTC, NTC or Pt 1000 probes) AI7
can be congured also for dry contact digital input
DI12
M6
Analogue input
(for PTC, NTC or Pt 1000 probes) AI6
can be congured also for dry contact digital input
DI11
M5
Analogue input
(for PTC, NTC or Pt 1000 probes) AI5
can be congured also for dry contact digital input;
DI10
M4
Analogue input
(for PTC, NTC or Pt 1000 probes) AI4
can be congured also for dry contact digital input
DI9
M3
Analogue input
(for NTC probes, 0-5 V, 0-10 V, 0-20 mA or 4-20 mA
transd.) AI3
can be congured also for dry contact digital input
DI8
M2
Analogue input
(for NTC probes, 0-5 V, 0-10 V, 0-20 mA or 4-20 mA
transd.) AI2
can be congured also for dry contact digital input
DI7
M1
Analogue input
(for NTC probes, 0-5 V, 0-10 V, 0-20 mA or 4-20 mA
transd.) AI1
can be congured also for dry contact digital input
DI6
GND Reference (GND)
12V Auxiliary power supply (12 VDC)
5V Ratiometric transducer power supply 0-5 V (5 VDC)
Connector 5
Number Description
PS Device power supply (115... 230 VAC)
PS Device power supply (115... 230 VAC)
Connector 6
Number Description
ITB INTRABUS port data
GND Reference (GND)
A+ If present, signal + RS-485 MODBUS master/slave
port
B- If present, signal - RS-485 MODBUS master/slave
port
C+ Signal + CAN port
C- Signal - CAN port
Connector 9
Number Description
DIHV5 High voltage digital input; DI5
DIHV5 High voltage digital input; DI5
Connector 10
Number Description
IN Input Pulse digital outpuyt (230 VAC max. 30 W)
OUT Pulse digital output

EVCO | 06.08.2021 | AZ | 13
DIHV5 DIHV5
002_c-pro3OEM_Connettori_001_0.1_AZ.eps
c-pro 3 OEM
AO4AO3 AO2 AO1 D14 D13
C01 NO1 C02 NO2 C03 NO3
IN7 IN6IN5 IN4IN3
C04 NO4 C05 NO5
IN2IN1 GND 12VS
NO6 C06 NC6
IB GND A+
DIHV1DIHV1 DIHV2 DIHV2
B- CAN+ CAN-
AC AC
5VS 21
ON
IN OUT
Pulse - EPB9BVE
114CP3OEE104
c-pro 3 OEM - Hardware manual
Plastic housing version (blind/LCD)
Connector 1
Number Description
CO1 K1 digital output common contact
NO1 K1 digital output normally open contact
(5 A res. at 250 VAC)
CO2 K2 digital output common contact
NO2 K2 digital output normally open contact
(5 A res. at 250 VAC)
CO3 K3 digital output common contact
NO3 K3 digital output normally open contact
(5 A res. at 250 VAC)
Connector 2
Number Description
CO4 K4 digital output common contact
NO4 K4 digital output normally open contact
(5 A res. at 250 VAC)
CO5 K5 digital output common contact
NO5 K5 digital output normally open contact
(8 A res. at 250 VAC)
Connector 3
Number Description
NO6 K6 digital output normally open contact
(16 A res. at 250 VAC)
CO6 K6 digital output common contact
NC6 K6 digital output normally closed contact
Connector 4
Number Description
DIHV1 DI1 High voltage digital input
DIHV1 DI1 High voltage digital input
DIHV2 DI2 High voltage digital input
DIHV2 DI2 High voltage digital input
Connector 5
Number Description
AC Device power supply (115... 230 VAC)
AC Device power supply (115... 230 VAC)
Connector 6
Number Description
IB INTRABUS port data
GND Reference (GND)
A+ If present, signal + RS-485 MODBUS master/slave
port
B- If present, signal - RS-485 MODBUS master/slave
port
CAN+ Signal + CAN port
CAN- Signal - CAN port
Connector 8
Connector 1 Connector 2 Connector 4
Connector 3 Connector 5
Connector 6
Connector 7
Connector 9
Connettore 10

EVCO | 06.08.2021 | AZ | 14114CP3OEE104
c-pro 3 OEM - Hardware manual
Connector 8
Number Description
AO4 Analogue output 4 (for 0-10 V or PWM)
AO3 Analogue output 3 (for 0-10 V or PWM)
AO2 Analogue output 2 (for 0-10 V or PWM)
AO1 Analogue output 1 (for 0-10 V or PWM)
DI4 Digital input
(dry contact and for pulse trains up to 2 KHz) DI4
DI3 Digital input
(dry contact and for pulse trains up to 2 KHz) DI3
IN7
Analogue input
(for PTC, NTC or Pt 1000 probes) AI7
can be congured also for dry contact digital input
DI12
IN6
Analogue input
(for PTC, NTC or Pt 1000 probes) AI6
can be congured also for dry contact digital input
DI11
IN5
Analogue input
(for PTC, NTC or Pt 1000 probes) AI5
can be congured also for dry contact digital input;
DI10
IN4
Analogue input
(for PTC, NTC or Pt 1000 probes) AI4
can be congured also for dry contact digital input
DI9
IN3
Analogue input
(for NTC probes, 0-5 V, 0-10 V, 0-20 mA or 4-20 mA
transd.) AI3
can be congured also for dry contact digital input
DI8
IN2
Analogue input
(for NTC probes, 0-5 V, 0-10 V, 0-20 mA or 4-20 mA
transd.) AI2
can be congured also for dry contact digital input
DI7
IN1
Analogue input
(for NTC probes, 0-5 V, 0-10 V, 0-20 mA or 4-20 mA
transd.) AI1
can be congured also for dry contact digital input
DI6
GND Reference (GND)
12VS Auxiliary power supply (12 VDC)
5VS Ratiometric transducer power supply 0-5 V (5 VDC)
Connector 7
Number Description
USB USB port, for device programming
Connector 9
Number Description
DIHV5 High voltage digital input; DI5
DIHV5 High voltage digital input; DI5
Connector 10
Number Description
IN Input Pulse digital outpuyt (230 VAC max. 30 W)
OUT Pulse digital output

EVCO | 06.08.2021 | AZ | 15
001_c-pro3OEM_SchemaElettricoSchedaGiorno_001_0.1_AZ
c-pro 3 OEM
K1
++ +
USB
INTRA
BUS
RS-
485
CAN
GND Data GND + - GND + -
K2 K3 K4 K5 K6
Max. 12 A
21
ON
AO4AO3 AO2AO1 M9 M8
C1 NO1 C2 NO2 C3 NO3
M7 M6 M5 M4 M3
C4 NO4C5 NO5
M2 M1 GND 12V
NO6C6 NC6
ITB GND A+
HV1HV1 HV2 HV2
B- C+ C-
PS PS
5V
DIHV5 DIHV5
IN OUT
12
ON
Pulse - EPB90V
114CP3OEE104
c-pro 3 OEM - Hardware manual
Electrical connection
Open frame version
Analog output 4
Digital output 1
Power supply
(115... 230 VAC)
Digital input 1 Digital input 2 Digital output 4 Digital output 2 Digital output 5 Digital output 3 Digital output 6
Analog output 3 Analog output 2 Analog output 1 Digital input 4 Digital input 3 Analog input 7 Analog input 6 Analog input 5 Analog input 4 Analog input 3 Analog input 2 Analog input 1
USB
cable
PC with
UNI-
PRO 3 BMS
Device
with
INTRABUS
Device
with
CAN port
Termination of the RS-485 MODBUS and CAN networks.
Polarisation of RS-485 MODBUS network
To terminate the RS-485 MODBUS network:
–Place the micro-switch 1 in position ON
To terminate the CAN network:
–Place the micro-switch 2 in position ON
The RS-485 MODBUS network can be polarised using the
UNI-PRO 3 development environment.
Electric system
(230 VAC)
Electric system
(230 VAC)
Mains supply
(115... 230 VAC)
Neutral
Pulse
valve
Phase
Digital input 5

EVCO | 06.08.2021 | AZ | 16
12
ON
c-pro 3 OEM
USB
21
ON
AO4AO3 AO2AO1 D14 D13 IN7IN6 IN5 IN4 IN3IN2 IN1 GND 12VS IB GND A+ B- CAN+ CAN-5VS
C01 NO1 C02 NO2 C03 NO3 C04 NO4 C05 NO5NO6 C06 NC6 DIHV1DIHV1 DIHV2 DIHV2 AC AC
K1
++ +
INTRA
BUS
RS-
485
CAN
GND Data GND + - GND + -
K2 K3 K4 K5 K6
Max. 12 A
DIHV5 DIHV5
IN OUT
Pulse - EPB9BVE
114CP3OEE104
c-pro 3 OEM - Hardware manual
Plastic housing version (blind/LCD)
Termination of the RS-485 MODBUS and CAN networks.
Polarisation of RS-485 MODBUS network
To terminate the RS-485 MODBUS network:
–Place the micro-switch 1 in position ON
To terminate the CAN network:
–Place the micro-switch 2 in position ON
The RS-485 MODBUS network can be polarised using the
UNI-PRO 3 development environment.
Analog output 4
Digital output 1
Power supply
(115... 230 VAC)
Digital input 1 Digital input 2 Digital output 4 Digital output 2 Digital output 5 Digital output 3 Digital output 6
Analog output 3 Analog output 2 Analog output 1 Digital input 4 Digital input 3 Analog input 7 Analog input 6 Analog input 5 Analog input 4 Analog input 3 Analog input 2 Analog input 1
USB
cable
PC with
UNI-
PRO 3 BMS
Device
with
INTRABUS
Device
with
CAN port
Electric system
(230 VAC)
Electric system
(230 VAC)
Mains supply
(115... 230 VAC)
Neutral
Pulse
valve
Phase
Digital input 5

EVCO | 06.08.2021 | AZ | 17
005_c-pro3OEM_InterfacciaUtente_001_0.1_AZ
005_c-pro3OEM_ON-OFF_001_0.1_AZ
114CP3OEE104
c-pro 3 OEM - Hardware manual
User interface version conguration
Keyboard
Key description
Keys Instructions
ESC
LEFT AND RIGHT
UP AND DOWN
ENTER
Switching ON/OFF the device
Progression Description
1
Connect the power supply:
it will be started an internal test that takes
typically a few seconds
2Touch UP and DOWN keys for 2 seconds:
the display will show the main menu
3To switch OFF the device switch OFF the power
supply
Accessing the procedure
Key Instructions
Touch UP and DOWN keys for 2 seconds:
the display will show the main menu
Touch ESC key few times to return to the previous
displays
Accessing the menu
Key Instructions
Touch UP and DOWN keys for 2 seconds:
the display will show the main menu
Touch UP or DOWN keys to move the menu cursor
Touch ENTER key to select the menu
Touch ESC key few times to return to the previous
displays
Parameters conguration
Key Instructions
Touch UP and DOWN keys for 2 seconds:
the display will show the main menu
Touch UP or DOWN keys to move the menu cursor
Touch ENTER key to select the menu
Touch UP or DOWN keys to see the parameters
Touch ENTER key to select the parameter
Touch UP or DOWN keys to set-up the value
Touch ENTER key to conrm the value
Touch ESC key few times to return to the previous
displays
Password
Key Instructions
Touch UP and DOWN keys for 2 seconds:
the display will show the main menu
Touch UP or DOWN keys to see the menu
“Password”
Touch ENTER key to select the menu:
the display will show “input password”
Touch ENTER key to enter the password
Touch UP or DOWN keys to set-up the password
“-19”
Touch ENTER key to conrm the password

EVCO | 06.08.2021 | AZ | 18
CAN
005_c-pro3OEM_ON-OFF_Cieco_001_0.1_AZ
CAN
005_c-pro3OEM_ON-OFF_Cieco_001_0.1_AZ
114CP3OEE104
c-pro 3 OEM - Hardware manual
Housing and blind version conguration
Through a controller with user interface
Conguration
The following procedures show an example of how to congure a blind programmable controller through a programmable
controller with user interface (in the example c-pro 3 OEM LCD):
1. Disconnect the controllers power supply
2. Connect the blind controller to the controller with user interface through the CAN CANBUS port
3. Connect the controllers power supply
Switching ON/OFF the device
Progression Description
1
Connect the blind controller to the controller
with user interface through the CAN CANBUS
port
2Touch UP and DOWN keys for 2 seconds:
the display will show the main menu
3To switch OFF the device switch OFF the power
supply
Accessing the procedure from c-pro 3 OEM LCD
Key Instructions
Touch UP and DOWN keys for 2 seconds:
the display will show the main menu
Touch ESC key few times to return to the previous
displays
c-pro 3 OEM blind
c-pro 3 OEM blind
c-pro 3 OEM LCD
c-pro 3 OEM LCD
CAN node address setting
Key Instructions
Touch UP and DOWN keys for 2 seconds:
the display will show the main menu
Touch UP or DOWN keys to see the “Network” menu
Touch ENTER key to select the menu
Touch ENTER key to enter the password
Touch UP or DOWN keys to set-up the password
“-19”
Touch ENTER key to conrm the password
Touch UP or DOWN keys to see the “CAN Bus” menu
Touch ENTER key to select the menu
Touch UP or DOWN keys to see the “NetworkNode”
menu
Touch ENTER key to select the menu
Touch UP or DOWN keys to set-up the node [1]
Touch ENTER key to conrm the node
Touch UP and DOWN keys to select the right arrow
“>”
Touch ENTER key
Touch ESC key few times to return to the previous
displays
The default setting of the CAN node is 1.
Operate on the controller with user interface to set the
“NetworkNode” parameter to [ 1 ].

EVCO | 06.08.2021 | AZ | 19114CP3OEE104
c-pro 3 OEM - Hardware manual
Accessing the menu from c-pro 3 OEM LCD
Key Instructions
Touch UP and DOWN keys for 2 seconds:
the display will show the main menu
Touch UP or DOWN keys to move the menu cursor
Touch ENTER key to select the menu
Touch ESC key few times to return to the previous
displays
Parameters conguration from c-pro 3 OEM LCD
Key Instructions
Touch UP and DOWN keys for 2 seconds:
the display will show the main menu
Touch UP or DOWN keys to move the menu cursor
Touch ENTER key to select the menu
Touch UP or DOWN keys to see the parameters
Touch ENTER key to select the parameter
Touch UP or DOWN keys to set-up the value
Touch ENTER key to conrm the value
Touch ESC key few times to return to the previous
displays
Password
Key Instructions
Touch UP and DOWN keys for 2 seconds:
the display will show the main menu
Touch UP or DOWN keys to see the menu
“Password”
Touch ENTER key to select the menu:
the display will show “input password”
Touch ENTER key to enter the password
Touch UP or DOWN keys to set-up the password
“-19”
Touch ENTER key to conrm the password

EVCO | 06.08.2021 | AZ | 20
CAN
005_c-pro3OEM_ON-OFF_Cieco_Interfaccia_001_0.1_AZ
114CP3OEE104
c-pro 3 OEM - Hardware manual
c-pro 3 OEM blind EPJgraph
Key description
Key Instructions
ON/STAND-BY
LEFT AND RIGHT
UP AND DOWN
ENTER
Through a remote user interface
Conguration
The following procedures show an example of how to congure a programmable controller through a remote user interface
(in the example EPJgraph):
1. Disconnect the power supply of the controller and the remote user interface
2. Connect the controller to the remote user interface through the CAN CANBUS port
3. Connect the power supply of the controller and the remote user interface
Switching ON/OFF the device from EPJgraph
Progression Description
1Connect the controller to the remote user
interface through the CAN CANBUS port
2Touch simultaneously the LEFT and ENTER keys
to access the “Network Status (CAN)” screen
3Touch the UP or DOWN keys to select the
correct Node (Status “OK”), touch ENTER key
4To switch OFF the device switch OFF the power
supply
Accessing the procedure from EPJgraph
Key Instructions
Touch simultaneously the LEFT and ENTER keys to
access the “Network Status (CAN)” screen
Touch the UP or DOWN keys to select the correct
Node (Status “OK”)
Touch ENTER key to access the main screen
Touch ON/STAND-BY key a few times to return to
the previous displays
Password
Key Instructions
Touch simultaneously the LEFT and ENTER keys to
access the “Network Status (CAN)” screen
Touch the UP or DOWN keys to select the correct
Node (Status “OK”)
Touch ENTER key to access the main screen
Touch UP or DOWN keys to see the “password”
menu
Touch ENTER key to select the menu:
the display will show “input password”
Touch ENTER key to enter the password
Touch UP or DOWN keys to set-up the password
“-19”
Touch ENTER key to conrm the password