Event Lighting PARRGBW12x8 User manual

1
Thin Propar Quad
Model No. PARRGBW12x8 /
PARRGBW5x8
USER MANUAL
For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications within this
manual are subject to change without notice. Event Lighting assumes no liability or responsibility for any
errors or omissions. Please consult Event Lighting for any clarification or information regarding this item.
www.event-lighting.com.au V1.0

2
CONTENTS
Safety Instructions
- Power Input & Power Linking
Product Installation
- Fuse replacement
Diagrams
- Lux Chart
- Dimensions
Control Board Operation
- DMX Addressing
- DMX Modes
- Dimmer Speed Setting
- Sound Mode
- Setting Static Colors
- Manual Color Mode
- Automatic Mode
- Master/slave Operation
DMX Values
- 10 Channels Mode
- 6 Channels Mode
- 4 Channels Mode
Technical Specifications Pixel Bar 12x3
Warranty

3
Safety Instructions
WARNING
•Do not open this device, there is no user-serviceable parts inside. Risk of electric shock.
•Do not look at the light source when the device is on.
•CAUTION: This unit's housing may be hot during and after operation.
•Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from adjacent surfaces.
•Do not leave any flammable material within 50 cm of this unit while operating or connected to power.
•Use a safety chain when mounting this device overhead.
•Do not operate this device outdoors or in any location where dust, excessive heat, water, or humidity may affect it.
•Do not operate this device if the housing, lenses, or cables appear damaged.
•Do not connect this device to a dimmer or rheostat.
•ONLY connect this device to a grounded and protected circuit.
•ONLY use the hanging bracket to carry this device.
•In case of a serious operating problem, stop using immediately.
•The maximum ambient temperature is 104° F (40° C). Do not operate this device at higher temperatures.
Power Input & Power Linking
This device has an auto-switching power supply work with input voltage range of 100~240 VAC, 50/60 Hz.
Link up to the maximum 16 devices at 120 VAC or 30 at 230 VAC. DO NOT exceed this number.
Product Installation
This device can be mounted in many orientations provided each individual device is secured by the use of correct
mounting bracket.
Use a safety chain when mounting this device overhead.
Fuse Replacement
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.
Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing (anticlockwise).
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing and fix it.

4
Lux Chart
12 LED version

5
5 LED version

6
Dimensions
12 LED version
5 LED version

7
CONTROL BOARD OPERATION
Display
Function
DMX Addr
To set DMX address
DMX Chan
To set DMX channel modes: CH10, CH06, CH04
Dimmer C
To set dimmer speeds: <01>, <02>, <03>, <04>
Sound
To set sound active mode and the sensitivity (Sen000 ~ Sen100)
Static C
To set static colors: Static Color R, G, B, W, GB, RB, RG, RGB, RW, GW, BW, RGW, RBW, GBW,
RGBW
Manual C
To set user mode intensity of R, G, B, W separately for color mixing and strobe rate
Auto Pro
To set built-in automatic programs: Pr 01 ~ Pr 05 and speeds Sp000 ~Sp100
Mas/Sla
To set Master/Slave modes
DMX
Addressing:
After select the "DMX Addr" and press Enter, then use Up and Down to set the desired DMX address (001~512),
press "Enter" again to confirm.
DMX Modes (Three DMX modes option)
After select the "DMX Chan" and press Enter, then use Up and Down to set the desired DMX mode (CH10 / CH06 / CH04),
press "Enter" again to confirm.
Dimmer Speed Setting:
After select the "Dimmer C" and press Enter, then use Up and Down to set the desired dimmer curves (01, 02, 03, 04),
press "Enter" again to confirm.
Sound Mode
Entered "Sound" mode, use <UP> and <DOWN> to set the sensitivity Sen000 ~ Sen100, press Enter to confirm.
Setting Static Colors
Entered "Static C" mode, you can select the desired solid color via the UP or DOWN buttons and confirm by Enter
Mode:
Value:
Function:
Static C
R
Red
G
Green
B
Blue
W
White
GB
Green + Blue
RB
Red + Blue
RG
Red + Green
RGB
Red + Green + Blue
RW
Red + White
GW
Green + White
BW
Blue + White
RGW
Red + Green + White
RBW
Red + Blue + White

8
GBW
Green + Blue + White
RGBW
Red + Green + Blue + White
Manual Color
Mode
This mode allows the user set intensity of R, G, B, W separately to get endless color mixing from the control
board without DMX controller to set the device to run strobe desired.
Entered "Manual C" mode, use <UP> and <DOWN> to select the " R / G / B / W " for Colors intensity or "S" for strobe
Use <UP> and <DOWN> to set the colors intensity values " 000 ~ 255" or Strobe speed values "S000 ~ S100"
(Freeze, Slow ~ Fast), then press "Enter" to confirm.
Automatic Mode
This fixture has a built-in automatic program.
Entered "Auto Pro" mode, use <UP> and <DOWN> to select the built-in programs "Pr 01 ~ Pr 05"
then press the "Enter" to confirm.
Use <UP> and <DOWN> to select the operating speed of the program(Value:S000 ~ S100, Freeze,Slow ~ Fast),
press "Enter" to confirm.
Mode:
Value:
Function:
Auto Pro
Pr 01
R G B W colors
switching
Pr 02
15 colors
switching
Pr 03
R G B W colors
fading
Pr 04
15 colors Fading
Pr 05
Color Macros
Fading
Master/Slave Operation
This mode allows for multiple units slave fixtures to follow a single master fixture.
1) Set the master fixture to one of the standalone operating modes: automatic, sound, static color or manual
color modes
2) Set the slaves, entered "Mas/Sla" mode, set to <S>, press Enter. "Slave
" will display.

9
DMX VALUES:
10 Channels Mode:
CHANNEL
VALUE
FUNCTION
1
000-255
Red 0% ~ 100%
2
000-255
Green 0% ~ 100%
3
000-255
Blue 0% ~ 100%
4
000-255
White 0% ~ 100%
5
000-255
Master DIMMER 0% ~ 100%
6
000-009
Strobe OFF
010-255
Strobe (slow-fast 1-30Hz)
000-019
No Function
020-039
RED 100% / GREEN 0% ~ 100% / BLUE 0%
040-059
RED 100% ~ 0% / GREEN 100% / BLUE
0%
060-079
RED 0% / GREEN 100% / BLUE 0% ~ 100%
080-099
RED 0% / GREEN 100% ~ 0% / BLUE
100%
100-119
RED 0% ~ 100% / GREEN 0% / BLUE
100%
120-139
RED 100% / GREEN 0% / BLUE 100% ~
0%
140-159
RED 100% / GREEN 0% ~100% / BLUE
0% ~ 100%
7
160-179
RED 100%~ 0% / GREEN 100% ~ 0% /
BLUE 100%
180-200
RED 100% / GREEN 100% / BLUE 100%
/WHITE 100%
201-204
Color Temprature 1
WARM
205-209
Color Temprature 2
210-214
Color Temprature 3
215-219
Color Temprature 4
220-224
Color Temprature 5
225-229
Color Temprature 6
230-234
Color Temprature 7
235-239
Color Temprature 8
240-244
Color Temprature 9
245-249
Color Temprature 10
COOL
250-255
Color Temprature 11
8
000-009
No Function

10
010-057
Auto Program 1
R G B W colors switching
058-106
Auto Program 2
15 colors switching
107-155
Auto Program 3
R G B W colors fading
156-204
Auto Program 4
15 colors Fading
205-255
Auto Program 5
Color Macros Fading
9
000-255
Speed of Auto Programs (Slow ~ Fast)
10
000-009
Use the dimmer of control board setting
010-069
Linear dimmer
070-130
Non-linear dimmer 1
131-191
Non-linear dimmer 2
192-255
Non-linear dimmer 3
6 Channels Mode:
CHANNEL
VALUE
FUNCTION
1
000-255
Red 0% ~ 100%
2
000-255
Green 0% ~ 100%
3
000-255
Blue 0% ~ 100%
4
000-255
White 0% ~ 100%
5
000-255
Master DIMMER 0% ~ 100%
6
000-009
No function
010-019
Sound Active
020-255
Strobe : Slow ~ Fast (1~30Hz)
4 Channels Mode:
CHANNEL
VALUE
FUNCTION
1
000-255
Red: 0% ~ 100%
2
000-255
Green: 0% ~ 100%
3
000-255
Blue: 0% ~ 100%
4
000-255
White: 0% ~ 100%

11
TECHNICAL
SPECIFICATIONS
12 LED version
5 LED version
Power supply: 100~240 V AC, 50/60
Hz ~
Power supply: 100~240 V AC, 50/60 Hz ~
Power consumption: 90 W
Power consumption: 40 W
DMX control channels: 4/6/10 chs
DMX control channels: 4/6/10 chs
DMX512 connection: 3-pin XLR
DMX512 connection: 3-pin XLR
Sound-control: via built-in microphone
Sound-control: via built-in microphone
LED type: 8 W Quad-color RGBW
LED type: 8 W Quad-color RGBW
Number of LEDs: 12
Number of LEDs: 5
Beam angle: 22°
Beam angle: 22°
Dimensions (LxWxH): 98 x 263 x
292.5 mm
Dimensions (LxWxH): 96 x 213 x 227 mm
Weight: 3.2 kg
Weight: 1.9 kg
Maximum ambient temperature Ta:
45°C
Maximum ambient temperature Ta: 45°
Maximum housing temperature TC (steady state): 80° C
Maximum housing temperature TC (steady state): 80° C
Min. distance from flammable surfaces: 0.5 m
Min. distance from flammable surfaces: 0.5 m
WARRANTY
Please refer to your local dealer or please contact Event Lighting.