Expolite TourBlinder 400 User manual

PRE-MANUAL
RAWMNLeng V201705-001 Änderungen sind ohne Ankündigung möglich.
Changes are possible without prior notice.
Tour-Blinder 400
led80050

1 Dimensions

DESCRIPTION
Features
Ÿ Easy multi fixture hanging system, outdoor version available
Ÿ 4*120w 3000k LED, no ultraviolet radiation
Ÿ 1300 lux in 5 meters
Ÿ 60 degree for beam angle
Ÿ 1/3/4/9 DMX channels
Ÿ 16 Bit Dimmer
Ÿ DMX Mode /Master-slave mode
Ÿ AC 100-240V 50/60Hz 480W
Ÿ With temperature sensor to extend the lamp life
Ÿ L: 373mm H:373mm W:193mm, Weight 9Kg
l IP65
SAFETY INSTRUCTIONS
This device has left the factory in perfect condition. In order to
maintain this condition and to ensure a safe operation, it
is absolutely necessary for the user to follow the safety
instructions and warning notes written in this user manual.
This device falls under protection-class I. Therefore it is essential that
the device should be earthed.
The electric connection must carry out by qualified person.
If the external flexible cable or cord of this luminaire is damaged,

it shall be exclusively replaced by the manufacturer or his
service agent or a similar qualified person in order to avoid a hazard.
Make sure that the available voltage is not higher than stated at the
end of this manual.
Make sure the power cord is never crimped or damaged by sharp
edges.
If this would be the case, replacement of the cable must be done by
an authorized dealer.
Always disconnect from the mains, when the device is not in use or
before cleaning it. Only handle the power cord by the plug. Never
pull out the plug by tugging the power cord.
Important:
Damages caused by the disregard of this user manual are not
subject to warranty. The dealer will not accept liability for any
resulting defects or problems.
DMX-512 control connection
The product has a DMX 512 input fitted with 3-pin XLR connectors.
Screened cables in compliance with EIA RS-485 specifications and the
following characteristics must be used for connections:
- 2 conductors plus screen
- 120Ohm impedance
- low capacitance
- max. transmission rate 250kBaud.
DMX-512 connection with DMX terminator
For installations where the DMX cable has to run a long distance or is
in an electrically noisy environment,such as in a discotheque, it is
recommended to use a DMX terminator. This helps in preventing
corruption of the digital control signal by electrical noise. The DMX
terminator is simply an XLR plug with a 120 OHM resistor connected
between pins 2 and 3,which is then plugged into the output XLR
socket of the last fixture in the chain.

Display Menu
Main menu Sub-menu Remark
Auto Mode
Auto Speed
default: Auto1
Speed:100
Auto1 1-100
Auto2 1-100
Auto3 1-100
Auto4 1-100
Auto5 1-100
Auto6 1-100
Static
Dimmer
Strobe
100
0
Dimmer mode
Stander Normal
speed
default：XXX Mode1 Fast
Mode 2 Medium
Mode 3 Slow
Backlight contr
ol
Keep screen
on
Exit the main menu,
black light will be closed
after 10/20/30 second
without operation
10 S
20 S
30 S
System info
Auto test Auto test
Hour Xx hour
Software
version V1.0
address 001-512 001 Default:001
DMX channel
Channel1 001-512
Default:9ch
Channel3 001-510
Channel4 001-509
Channel9 001-504
Master/slave
mode
Master mode
Slave mode
Slave
mode Default: Slave mode
Fan mode Auto
fast Auto Default: Auto
Temperature
LED1
Xx ℃ LED2
LED3

LED4
LED Scan rate 600Hz
Default:1200Hz
1200Hz
2000Hz
4000Hz
25KHz
Main functions
1. address:Current DMX address
A.Setting DMX address by button
press ENTER button when show the address menu, then adjust
the DMX address by pressing [UP] or [DOWN] button
Press [ENTER] to confirm or pressing [ESC] to return to main
menu.
B.Setting DMX address by controller
1.Set the DMX value of channel 5 to 10-15,channel 17 to 20-26,
channel 7 to 30-36,channel 8 to 40-46,then the devices
connected to the controller will enter to the setting address
mode
2. Set the DMX value of channel 1 from 0-59,then you will see
the the first number of the Address change to (channel 1
vaule)/10.
For example,when set the value of channel 1 to 20,the first
DMX address number will be 2(20/10=2) ,
3. Set the DMX value of channel 2 from 0-99,then you will see
the the sencond number of the Address change to (channel 2
vaule)/10.
For example,when set the value of channel 2 to 30,the first
DMX address number will be 2(30/10=3) ,
4.Set the DMX value of channel 3 from 0-99,then you will see
the the third number of the Address change to (channel 3
vaule)/10.
For example,when set the value of channel 1 to 40,the first
DMX address number will be 3(40/10=4) ,
And the DMX address you set by conctroller will be 234.
5. Set the DMX value of channel 4 to 255,then you will save
the DMX address setted by the controller.
Caution: It won’t save the address if the address number is

over 512
6. set the value of channel 5 -8 out of the value range show on
the step 1,and the device will exit the setting address mode
2. config
Setting DMX mode
press ENTER button when show the channel menu, then
select the DMX mode by pressing [UP] or [DOWN] button
Setting Dimmer Curve
press ENTER button when show the dimmer curve menu,
then select the dimmer curve by pressing [UP] or [DOWN]
button
Setting Cipher
press ENTER button when show the cipher setup menu, then
setup cipher by pressing [UP] or [DOWN] button
Key mode
press ENTER button when show the key mode menu, then
select lock or unlock by pressing [UP] or [DOWN] button
Show Temperature
press ENTER button when show the Temp Uint CS menu,
select the way of showing the fixture’s temperature in ℃ or ℉
by pressing [UP] or [DOWN] button
DMX status
press ENTER button when show the DMX Status menu, then
select clear value or hold value by pressing [UP] or [DOWN]
button
Display mode
press ENTER button when show the Display Mode menu,
then select auto or on by pressing [UP] or [DOWN] button
3. System info
Temperature
press ENTER button when show the Temperature menu, then
it will show the temperature of the fixture
Fixture time
press ENTER button when show the Fixture time menu, then it

will show how long time of the fixture already used
4. Color menu
press ENTER button when show the Color menu, press Enter
button to select the color mode, then adjust the color by
pressing [UP] or [DOWN] button
5. White balance
press ENTER button when show the white balance menu,
press Enter button to select the color mode, then adjust the
color by pressing [UP] or [DOWN] button
6. Auto test
press ENTER button when show the auto test menu, select
test mode by pressing [UP] or [DOWN] button
DMX functions and values
1CH Mode
No. Function Value Description Remark
1 Dimmer 000-
255 0-100%
3CH Mode
No. Function Value Description Remark
1 Master Dimmer 000-255 0-100%
2 Fine
MasterDimmer 000-255 0-100%
3 Strobe
000-010 No Function
011-132 Strobe Slow to fast
133-255 Macro
Strobe Slow to fast
4CH Mode
No. Function Value Description Remark

1 LED head 1 000-255 0-100%
2 LED head 2 000-255 0-100%
3 LED head 3 000-255 0-100%
4 LED head 4 000-255 0-100%
9CH Mode
No. Function Value Description Remark
1 Master
Dimmer 000-255 0-100%
2 Fine
MasterDimmer 000-255 0-100%
3 Strobe 000-010 NoFunction
011-132 Strobe Slow to
fast
133-255 Macro Strobe Slow to
fast
4 LED head 1 000-255 0-100%
5 LED head 2 000-255 0-100%
6 LED head 3 000-255 0-100%
7 LED head 4 000-255 0-100%
8
Auto Mode
000-010
011-040
041-080
081-120
121-170
171-220
221-225
No Function
auto1
auto2
auto3
auto4
auto5
auto6
9 Dimmer mode
000-010
011-040
041-080
081-120
121-255
Dimmer
mode
Mode1
Moder2
Mode3
Dimmer
mode
Fast
Medium
Slow