fantastic furniture BUTTONS User manual

BUTTONS
QUEEN BED
0

Read through the instructions carefully
before you begin.
Assembly checklist
Identify and lay out all of the components
before you begin assembly.
Unless instructed, do not fully tighten screws
until the item is fully assembled.
!Never use power tools unless specifically instructed. They can damage your components or
hardware if used incorrectly.
!The most common mistakes made during assembly are using the wrong hardware or getting
components back to front.
!Always use a soft surface (such as carpet or cardboard) when assembling your product to
avoid scratching or damaging the surface of the product.
!Bulky items such as wardrobes and bunk beds should be assembled in the room they will be
used in as they may not fit through a door once assembled.
!Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or website for
product care instructions.
!If you are having any difficulties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
PAGE 3www.fantasticfurniture.com.au
ad through the instructions care
sure you have all the required
before you begin.
fy and lay out all of the compon
nstructed, do not fully tighten
r use power tools unless instruc

Timber Cross Rail (P4) ; Side Rail (P5) ; Center Rail (P6) ;
Headboard (P1) ; Slats (P9)
Box 1 :
Parts list
Side Rail (P5)
Side Rail (P5) Footboard
(P2)
Headboard
(P1)
Box 2 :
Footboard (P2) ; Headboard/Footboard Leg (P3) ;
28 x Slats (P9)
Bracket (P7) ;
Bracket(P7)
Bracket(P7)
Support Leg (P8)Support Leg (P8)
(P4)
(P6)
; Hardware Pack
Support Leg (P8)
Headboard/Footboard
Leg (P3)
Headboard/Footboard
Leg (P3)
Timber Cross Rail
(H1) (H2)
(H6)
8 x M8 x 18mm
(Washer)
(Bolt) 1 x M5 (Allen Key)
22 x M8 x 19mm 3 x M4 x 32mm
(H7)
(Screw)
(H5)
4 x M8 x 40mm
(Bolt)
(H9)
4 x M8
(H8)
1 x Spanner
(H4)
(Plastic nut)
8 x M6 x 13mm
(H10)
4 x M6 x 40mm
(Bolt)
(H11)
4 x M6 x 35mm
(Bolt)
(H3)
14 x M8 x 20mm
(Bolt)
(Nut)

Allen Key
(H1)
8 x Bolt 18mm
(H2)
(P1)
(P1)
bolts until step 6.
(H2)
(H1)
Install the bolts (H1) to the brackets by using Allen Key (H2) as shown, do not tighten the bolts
and keep them 8 mm loose. Then attach side rail (P5) to headboard (P1) and footboard (P2)
by slotting the bracket on the side rail (P5) over the bolt as shown. No need to tighten
(P2)
(P5) (P2)
8 x Bolt 20mm
(H6) (H3)
8 x Washer M8
(P3)
(H6)(H3)
(H2)
Allen Key
(H2)
Attach legs (P3) to the bottom of headboard (P1) and footboard (P2).
With 8 x Bolt 20mm (H3) and 8 x Washer (H6) by using Allen Key (H2).

4 x nut (H9), attach 2 x bracket (P7) to the centre rail (P6) using 2 x bolt (H3) and
(H5)
(H6)
(H6)
(H9)
(H8)
(P6)
(P8)
(P6)
(P8)
(P8)
(P6)
Attach the support legs (P8) to the centre rail ( P6) using 4 x Bolt (H5) , 8 x Washer (H6) and
2 x washer (H6) as shown.
(H2)
Make sure the ends
are aligned
(P6)
4 x Bolt 40mm
(H6)
(H5)
10 x 2 x Bolt 20mm
(H3) (H9)
4 x Nut M8
1 x Spanner
(H8) Allen Key
(H2)
Washer M8 (H6)
(H3)
(H2)
(P7)
screwdriver
Phillips head
(no provided)
(H4)
(Plastic nut)
4 x M6 x 13mm
(H11)
4 x M6 x 35mm
(Bolt)
(H11)
(H4)
Attach the plastic nut (H4) to the centre rail (P6) using 4 x Bolt (H11).
(H11)
(H4)

PAGE 7
4 x Bolt 20mm
(H6) (H3)
4 x Washer M8
Slot the Centre rail (P6) into the headboard (P1) and footboard (P2).
Rotate 3/4 bolts (H3) using Allen Key (H2) to the headboard (P1)
and footboard (P2). No need to tighten bolts until step 6.
(H6)
(H3) (P6)
(P1)
(P5)
(P2)
Allen Key
(H2)
(H2)
Attach the plastic nut (H4) to the side rail (P5) by using 4 x Bolt (H10) .
(H4)
4 x Plastic nut
4 x Bolt 40mm
(H10)
Phillips head
screwdriver
Allen Key
(H2)
(H2)
(P1)
(P5) (P2)
(H4)
(H10)
Now tighten all the bolts on the corner bracket and tighten bolts on the headboard (P1)
and footboard (P2).
(no provided)

(P6)
(P9)
(P9)
First Step
Side rail
support wood Side rail
support wood
Second StepThird Step
PAGE 8
Step 8
(H7)
3 x
Screw 32mm Phillips head
screwdriver
(no provided) (H7)
(P4)
by using 3 x screw (H7).
Attach the cross rail (P4) to the centre of side rails (P5) and centre rail (P6)
Fix slats (P9) on one end of the side rail (P5) and centre rail (P6). By using the
plastic nut (H4) as stopper. Then spread out the slats and fix the slats to the other
end of the side rail (P5) and centre rail (P6). By using the plastic nuts (H4) as stopper.

Step 9
PAGE 9

Version 1.0
TOTO
TALLBOY 5 DRAWER
fantasticfurniture.com.au