fantastic furniture Hamilton Buffet User manual

Hamilton
Buet
fantasticfurniture.com.au
Version 1.0

fantasticfurniture.com.au
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!
WARNING: ENSURE THE WALL STRAP IS ATTACHED TO
AVOID SERIOUS INJURY.
To avoid any serious or fatal injury, this product has been supplied
with a wall strap to prevent toppling. We strongly recommend that
this product is permanently fixed to the wall or other suitable sur-
face. Connecting attachments for your wall are not included since
dierent surface materials require dierent attachments. Please seek
professional advice if you are in doubt of what wall connections to
use.
Recommended weight capacity : 80kgs on top.
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture
Page 2

Page 3
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
!Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
!The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
!Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
!Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
!Never use any glue until you are certain that the parts belong together.
!Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
!If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
!Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Parts list
Top Panel (P1);
Bottom Panel (P2);
Left Side Panel (P3);
Right Side Panel (P4);
3 x Shelf Panes (P5);
3 x Back Panels (P6);
Divider (P7);
Divider (P8);
3 x Rail (P9);
2 x Door (P10);
Rail (P11);
2 x Support Legs (P12);
Left Drawer Front (P13);
Middle Drawer Front (P14);
Right Drawer Front (P15);
3 x Left Drawer Side (P16);
3 x Right Drawer Side (P17);
3 x Drawer Back (P18);
3 x Drawer Base (P19);
Door (P20)
Hardware pack
Top Panel
(P1)
Shelf
Panel
(P5)
Shelf
Panel
(P5)
Shelf
Panel
(P5)
Right Side
Panel (P4)
Left Side
Panel (P3)
Rail
(P9)
Rail
(P9)
Rail
(P11)
Door
(P10)
Door
(P20)
Door
(P10)
Support
Legs
(P12)
x2
Rail
(P9)
Back
Panel
(P6)
Back
Panel
(P6)
Divider
(P7)
Bottom
Panel
(P2)
Divider
(P8)
Back
Panel
(P6)
Left
Drawer
Side
(P16)
Drawer
Front
(P13&P14&P15)
Right
Drawer Side
(P17)
Drawer
Back (P18)
Drawer Base
(P19)
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
Page 4
fantasticfurniture.com.au
DO NOT USE
20 x Dowels
(H1)
16 x Long
Screws
(H2)
30 x Small
Screws
(H5)
3 x CL Runner
Tracsk
(H6)
35 x Cam
Bolts
(H3)
35 x Cam
Nuts
(H4)
3 x CR Runner
Tracks
(H7)
3 x DL
Runners
(H8)
3 x DR
Runners
(H9)
6 x Handles
(H10)
2 x Long
Dowels
(H18)
2 x Adjusters
(H17)
6 x Handle
Bolts
(H11)
8 x Wedges
(H12)
8 x Screws
(H13)
4 x Hinges
(H14)
2 x Hinges
(H19)
36 x Hinge
Screws
(H15)
12 x Shelf
Plugs
(H16)
2 x Safety
Strap
Screws
(H21)
2 x Safety
Straps
(H20)
4 x Washers
(H22)

1 x CL Runner
Track (H6)
6 x Small
Screws (H5)
1 x CR Runner
Track (H7)
1 x CL Runner
Track (H6)
6 x Small
Screws (H5)
1 x CR Runner
Track (H7)
2 x Cam Bolts
(H3)
(P3)
(P4)
(P7)
(P7)
You will need
Step 1
Step 2
You will need
Attach 8 x Cam Bolts (H3) to Left&Right Side
Panels (P3&P4) as shown by tightening with the
Phillips Head Screwdriver. Attach 1x CL Runner (H6) to Left Side Panel (P3) and 1x CR Runner
(H7) to Right Side Panel (P4) with 6 x Small Screws (H5) by tightening with the Phillips Head
Screwdriver.
fantasticfurniture.com.au Page 5
8 x Cam Bolts
(H3)
Phillips Head
Screwdriver
CL
CR
H3
H3
H6
H6
H5
H5
H5
H5
H6
CL
H5
H6
H7
H7
H7
CR
H5
H7
Phillips Head
Screwdriver
Attach 2 x Cam Bolts (H3) , 1 x CL Runner Track (H6) and 1 x CR Runner
Track (H7) to each side of Divider (P7) with 6 x Small Screws (H5) by tightening
with the Phillips Head Screwdriver.
H5
H5
H3
H3
FLIP

Insert 2 x Long Dowels (H18) into Dividers (P7&P8). Insert 2 x Cam Nuts (H4)
into Rail (P9). Rotate the nuts so the arrows point towards the incoming bolts.
Attach Dividers (P7&P8) to Rail (P9) by tightening all nuts with the Phillips Head
Screwdriver.
(P7)
(P8)
(P8)
(P8)
(P9)
fantasticfurniture.com.au Page 6
CL
H5
H6
H6
CR
H5
H7
H7
Attach 2 x Cam Bolts (H3) , 1 x CL Runner Track (H6) and 1 x CR Runner
Track (H7) to each side of Divider (P8) with 6 x Small Screws (H5) by tightening
with the Phillips Head Screwdriver.
This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.
FLIP
H5
H5
H3
H3
H4
H18
H18
H4
Step 4
You will need
2 x Cam Nuts
(H4)
Phillips Head
Screwdriver
2 x Long
Dowels (H18)
1 x CL Runner
Track (H6)
6 x Small
Screws (H5)
1 x CR Runner
Track (H7)
2 x Cam Bolts
(H3)
Step 3
You will need
Phillips Head
Screwdriver

Step 5
You will need
Phillips Head
Screwdriver
Attach 3 x Cam Bolts (H3) to Rail (P11) by tightening with the Phillips Head Screwdriver.
You will need
Phillips Head
Screwdriver
Step 6
Insert 3 x Cam Nuts (H4) into Bottom Panel (P2). Rotate the nuts so the arrows point
towards the incoming bolts. Attach Rail (P11) to Bottom Panel (P2) by tightening all nuts
with the Phillips Head Screwdriver.
(P11)
(P11)
(P2)
fantasticfurniture.com.au Page 7
3 x Cam Nuts
(H4)
3 x Cam
Bolts (H3)
H3
H4
H3
H3
H4
H4

You will need
Phillips Head
Screwdriver
Step 7
You will need
Phillips Head
Screwdriver
Step 8
Attach Bottom Panel (P2) to Dividers (P7&P8) with 4 x Long Screws (H2) and 4 x Dowels (H1)
by tightening with the Phillips Head Screwdriver.
(P7)
(P8)
(P2)
fantasticfurniture.com.au Page 8
2 x Cam Nuts
(H4)
4 x Dowels
(H1)
4 x Long
Screws (H2)
Insert 2 x Cam Nuts (H4) into Rails (P9x2). Rotate the nuts so the arrows point
towards the incoming bolts. Attach Rails (P9x2) to Divider (P7&P8) by tightening all
nuts with the Phillips Head Screwdriver.
H1
H1
H2
H2
H2
H4
H4
H18
H18
H2
(P9)
(P9)
(P7)
(P8)

You will need
Step 9
Step 10
You will need
Phillips Head
Screwdriver
4 x Cam Nuts
(H4)
4 x Dowels
(H1)
Phillips Head
Screwdriver
4 x Cam Nuts
(H4)
4 x Dowels
(H1)
Insert 4 x Dowels (H1) and
4 x Cam Nuts (H4) into Rails
(P9&P11) and Bottom Panel (P2).
Rotate the nuts so the arrows point towards
the incoming bolts. Attach Left Side Panel (P3) to Rails (P9&P11) and Bottom Panel (P2) by
tightening all nuts with the Phillips Head Screwdriver.
Insert 4 x Dowels (H1) and
4 x Cam Nuts (H4) into Rails
(P9&P11) and Bottom Panel (P2).
Rotate the nuts so the arrows point towards
the incoming bolts. Attach Right Side Panel (P4) to Rails (P9&P11) and Bottom Panel (P2) by
tightening all nuts with the Phillips Head Screwdriver.
(P3)
(P9)
(P9)
(P2)
(P2)
(P4)
(P11)
(P11)
fantasticfurniture.com.au Page 9
H1 H4
H4
H1

You will need
Step 11
Step 12
Attach 2 x Support Legs (P12) to Bottom Panel (P2). Insert the 2 x Adjusters (H17)
into the 2 x Support Legs (P12).
Gently stand the unit upright. Slide Back Panels (P6x3) into the grooves of
Left & Right Side Panel (P3&P4) and Dividers (P7&P8).
(P3)
(P7)
(P8)
(P2)
(P12)
(P12)
(P4)
(P6)
(P6)
(P6)
fantasticfurniture.com.au Page 10
H17
H17
2 x Adjusters
(H17)

Attach 8 x Cam Bolts (H3) to Top Panel (P1) by tightening with the Phillips Head Screwdriver.
Insert 8 x Dowels (H1) into Dividers (P7&P8) and Left&Right Side Panel (P3&P4).
Insert 8 x Cam Nuts (H4) into Dividers (P7&P8) and Left&Right Side Panel (P3&P4).
Rotate the nuts so the arrows point towards the incoming bolts. Attach Top Panel (P1)
to Dividers (P7&P8) and Left&Right Side Panel (P3&P4) by tightening all nuts with the
Phillips Head Screwdriver.
You will need
Step 13
You will need
Step 14
Phillips Head
Screwdriver
8 x Cam Nuts
(H4)
8 x Dowels
(H1)
Phillips Head
Screwdriver
(P3)
(P7)
(P8)
(P4)
(P1)
(P1)
fantasticfurniture.com.au Page 11
H3
H3
H3
H4
H1
H3
H3
H3
H3
H3
8 x Cam Bolts
(H3)

Insert 12 x Shelf Plugs (H16) into the end cavities of the cabinet as shown.
Insert the 3 x Shelf Panels (P5) and balance on top of the plugs.
You will need
Step 15
You will need
Step 16
Phillips Head
Screwdriver
Attach 4 x Hinges (H14) to Doors (P10x2), attach 2 x Hinges
(H19) to Door (P20), securing with 12 x Small Screws (H15).
Tighten with a Phillips Head Screwdriver. Make sure the 4 x
Hinges (H14) are assembled on Door (P10), the 2 x Hinges (H19) are assembled
on door (P20).
(P3)
(P5)
(P20)
(P10) x2
(P5)
(P5)
(P7)
(P8)
(P4)
H16
H15
H15
H15
H15
H19
H19
H15
H14
H14
H14
H16
H16
fantasticfurniture.com.au Page 12
12 x Shelf
Plugs (H16)
4 x Hinges
(H14)
2 x Hinges
(H19)
12 x Hinge
Screws (H15)
H19
H15

You will need
Step 17
You will need
Step 18
Secure Doors
(P10x2&P20) to the
main unit by attaching
the other end of the 6 x
Hinges (H14,H19) with
24 x Hinge Screws (H15)
as shown. Tighten with a
Phillips Head Screwdriver.
Attach 3 x Handles (H10) to Doors (P10x2&P20) with 3 x Handle
Bolts (H11) by tightening with the Phillips Head Screwdriver.
Phillips Head
Screwdriver
Phillips Head
Screwdriver
(P3)
(P20)
(P10)
(P10)
(P8)
(P4)
fantasticfurniture.com.au Page 13
24 x Hinge
Screws (H15)
3 x Handles
(H10)
3 x Handle
Bolts (H11)
H15
H15
H15
H15
H15
(P3)
(P20)
(P10)
(P10)
(P4)
H10
H10
H11
H11
H11
H10
H10
H11

Step 20
You will need
Step 21
Insert 4 x Cam Nuts (H4) into the holes of Drawer Sides (P16, P17).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push Drawer Sides (P16, P17) into place and tighten the cam nuts.
Slide Drawer Base (P19) into the groove in Drawer Sides (P16, P17).
(P13)
(P17)
(P17)
(P19)
(P16)
(P16)
fantasticfurniture.com.au Page 14
H4
H4
H4 H4
Phillips Head
Screwdriver
4 x Cam Nuts
(H4)
Step 19
You will need
Attach 4 x Cam Bolts (H3) to Left Drawer Front (P13)
by tightening with the Phillips Head Screwdriver.
H3
H3
H3 H3
Phillips Head
Screwdriver
4 x Cam
Bolts (H3)
(P13)
(P13)

Step 22
You will need
Attach Drawer Back (P18) to Drawer Sides (P16,P17) with 4 x Long Screws (H2).
Make sure that the groove lines up the whole way around the drawer.
Step 23
You will need
1 x DL Runner
(H8)
4 x Small
Screws (H5)
1 x DR Runner
(H9)
Step 24
You will need
1 x Handle
(H10)
Phillips head
screwdriver
1 x Handle
Bolt (H11)
(P16)
(P17)
(P17)
(P18)
(P16)
fantasticfurniture.com.au Page 15
H11
H5
H8
H9
H5
H5
H5
Phillips Head
Screwdriver
4 x Long
Screws (H2)
Phillips Head
Screwdriver
Attach 1 x DL Runner (H8) to Left Drawer Side (P16) and 1 x DR Runner (H9) to Right Drawer
Side (P17) with 4 x Small Screws (H5) by tightening with the Phillips Head Screwdriver.
Attach 1 x Handle (H10) to Left Drawer Front (P13) with
1 x Handle Bolt (H11) by tightening with the Phillips Head Screwdriver.
H2
H2
H10
(P13)
(P13)
(P13)

Step 26
You will need
Step 27
Insert 4 x Cam Nuts (H4) into the holes of Drawer Sides (P16, P17).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push Drawer Sides (P16, P17) into place and tighten the cam nuts.
Slide Drawer Base (P19) into the groove in Drawer Sides (P16, P17).
(P14)
(P17)
(P17)
(P19)
(P16)
(P16)
fantasticfurniture.com.au Page 16
H4
H4
H4 H4
Phillips Head
Screwdriver
4 x Cam Nuts
(H4)
Step 25
You will need
Attach 4 x Cam Bolts (H3) to Middle Drawer Front (P14)
by tightening with the Phillips Head Screwdriver.
H3
H3
H3 H3
Phillips Head
Screwdriver
4 x Cam
Bolts (H3)
( P14)
(P14)

Step 28
You will need
Attach Drawer Back (P18) to Drawer Side (P16,P17) with 4 x Long Screws (H2).
Make sure that the groove lines up the whole way around the drawer.
Step 29
You will need
1 x DL Runner
(H8)
4 x Small
Screws (H5)
1 x DR Runner
(H9)
Step 30
You will need
1 x Handle
(H10)
Phillips head
screwdriver
1 x Handle
Bolt (H11)
(P16)
(P17)
(P17)
(P18)
(P16)
fantasticfurniture.com.au Page 17
H11
H5
H8
H9
H5
H5
H5
Phillips Head
Screwdriver
4 x Long
Screws (H2)
Phillips Head
Screwdriver
Attach 1 x DL Runner (H8) to Left Drawer Side (P16) and 1 x DR Runner (H9) to Right Drawer
Side (P17) with 4 x Small Screws (H5) by tightening with the Phillips Head Screwdriver.
Attach 1 x Handle (H10) to Middle Drawer Front (P14) with
1 x Handle Bolt (H11) by tightening with the Phillips Head Screwdriver.
H2
H2
H10
( P14)
(P14)
( P14)

Step 32
You will need
Step 33
Insert 4 x Cam Nuts (H4) into the holes of Drawer Sides (P16, P17).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push Drawer Sides (P16, P17) into place and tighten the cam nuts.
Slide Drawer Base (P19) into the groove in Drawer Sides (P16, P17).
(P15)
(P17)
(P17)
(P19)
(P16)
(P16)
fantasticfurniture.com.au Page 18
H4
H4
H4 H4
Phillips Head
Screwdriver
4 x Cam Nuts
(H4)
Step 31
You will need
Attach 4 x Cam Bolts (H3) to Right Drawer Front (P15)
by tightening with the Phillips Head Screwdriver.
H3
H3
H3 H3
Phillips Head
Screwdriver
4 x Cam
Bolts (H3)
(P15)
(P15)

Step 34
You will need
Attach Drawer Back (P18) to Drawer Sides (P16,P17) with 4 x Long Screws (H2).
Make sure that the groove lines up the whole way around the drawer.
Step 35
You will need
1 x DL Runner
(H8)
4 x Small
Screws (H5)
1 x DR Runner
(H9)
Step 36
You will need
1 x Handle
(H10)
Phillips head
screwdriver
1 x Handle
Bolt (H11)
(P16)
(P17)
(P17)
(P18)
(P16)
fantasticfurniture.com.au Page 19
H11
H5
H8
H9
H5
H5
H5
Phillips Head
Screwdriver
4 x Long
Screws (H2)
Phillips Head
Screwdriver
Attach 1 x DL Runner (H8) to Left Drawer Side (P16) and 1 x DR Runner (H9) to Right Drawer
Side (P17) with 4 x Small Screws (H5) by tightening with the Phillips Head Screwdriver.
Attach 1 x Handle (H10) to Right Drawer Front (P15) with
1 x Handle Bolt (H11) by tightening with the Phillips Head Screwdriver.
H2
H2
H10
(P15)
(P15)
(P15)

Step 37
Secure Back Panels (P6 x 2) in place with 8 x Wedges (H12) using 8 x Wedge
Screws (H13) by tightening with the Phillips Head Screwdriver. Use 2 x Safety Strap Screws (H21)
and 2 x Washers (H22) to connect 2 x Safety Straps (H20) on Top Panel (P1).
Step 38
You will need
8 x Wedges
(H12)
8 x Wedge
Screws (H13)
Phillips head
screwdriver
(P1)
(P6)
(P6)
(P13)
(P14) (P15)
fantasticfurniture.com.au Page 20
H21
H12
H13
H22
H20
2 x Safety Strap
Screws (H21)
2 x Safety
Straps (H20)
2 x Washers
(H22)
Insert the assembled drawers into the corresponding compartments as shown.
Ensure the drawers slide easily along the rails.