fantastic furniture Alexis User manual

Alexis
Buffet 3 Drawer Oak

r

Drawer Door
(P11)
Drawer Back
(P13)
Drawer Left Panel
(P13)
DrawerRight Panel
(P15)
Drawer B ottom
(P16)
Drawer Door
(P11)
Drawer Back
(P13)
Drawer Left Panel
(P13)
DrawerRight Panel
(P15)
Drawer Bottom
(P16)
Drawer Door
(P11)
Drawer Back
(P12)
Drawer Left Panel
(P13)
DrawerRight Panel
(P14)
Drawer Bott om
(P15)
Top Panel (P1)
Bottom Panel (P2)
Right Panel (P3)
Left Panel (P4)
Middle Panel (P5)
Long Shelf (P6)
2 x Long Back Panels (P7)
Short Back Panel (P8)
Left Door (P9)
Right Door (P10)
3 x Drawer Front (P11)
Drawer Backs (P12)
Drawer Left Panels (P13)
Drawer Right Panels (P14)
Drawer Bottoms (P15)
3 x
3 x
3 x
3 x
Top Panel (P1)
Bottom Panel (P2)
Right Panel (P3)
Left Panel (P4)
Middle Panel (P5)
Long Shelf (P6)
2 x Long Back Panels (P7)
Short Back Panel (P8)
Left Door (P9)
Right Door (P10)
3 x Drawer Front (P11)
Drawer Backs (P12)
Drawer Left Panels (P13)
Drawer Right Panels (P14)
Drawer Bottoms (P15)
3 x
3 x
3 x
3 x
6 x Slide
(H18)
12 x Long Screw
(H19)
28 x Cam Bolts
(H1)
28 x Cam Nuts
(H2)
16 x Dowels
(H3)
4 x Hinges
(H4) 70 x Short Screws
(H5)
4 x Legs
(H6)
12 x Washers
(H7)
4 x Long Bolts
(H8)
1 x Allen Key
(H9) 4 x Levelling Feet
(H10)
12 x Wedges
(H11)
1 x Middle Screw
(H12)
2 x Connectors
(H13)
9 x Short Bolts
(H14)
2 x Washers
(H15)
1 x Wall Strap
(H16)
6
7
8
6
0
5 x Handles
(H20) 2 x Felt Pads
(H21)
Top Panel
(P1)
Bottom Panel
(P2)
1 x Screwdirver
(H22)

16 x Washers
(H7)
12 x Short Bolts
(H8)
1 x Allen Key
(H9)
4 x Levelling Feet
(H10)
H 1 7
H10
H 9
H 8
H 7
2 x Connectors
(H13)
4 x Long Bolts
(H14)
H 1 4
H 7
H17
2 x Felt Pads
(H21)
H13
H13
6 x Cam Bolts
(H1)
6 x Dowels
(H3)
Phillips Head
Screwdriver
(P2)
Insert 6 x Dowels (H3) into Bottom Panel (P2) and secure 6 x Cam Bolts (H1)
to Unit Bottom Pane l(P2) by tightening with the Phillips Head Screwdriver.
Stick 2 x Felt Pads (H21) to the centre of each connector (H13).
Align and position 4 x Legs (H6) onto the pre-drilled holes on the Bottom
Panel (P2). Align and position the 2 x Connectors (H13) between the
Legs (H6) as shown ensuring the side with the Felt Pads (H17) is on the
Bottom Panel (P2).Using 3 x Washers (H7) and 3 x Short Bolts (H8), secure 1 x Leg (H6) to
the Bottom Panel (P2), tightening using the Allen Key (H9).
Secure the Connector (H13) to the Table Leg (H6) and Bottom Panel (P2)
using 1 x Washer (H7) and 1 x Long Bolt (H14), tightening using the Allen Key (H9).
Attach 1 x levelling foot (H10) to one leg (H6) and tighten by turning clockwise.
Repeat this step for the other 3 x Legs (H6).

Phillips Head
Screwdriver
4 x Dowels
(H3)
4 x Cam Bolts
(H1)
Insert 2 x Dowels (H3) into Right Panel (P3) and secure 2 x Cam Bolts (H1)
to Right Panel (P3) by tightening with the Phillips Head Screwdriver.
Repeat step for Left Panel (P4)
Insert 2 x Dowels (H3) into Middle Panel (P5) and secure 2 x Cam Bolts (H1)
to Middle Panel (P5) by tightening with the Phillips Head Screwdriver,
Then turn over, repeat previous step for another side of Middle Panel (P5)
(P9)(P10)
4 x Cam Nuts
(H2)
(H2)
(H3)
(P6) (P5)
Align and attach Long Shelf (P6) between the Left Panel (P4) and Middle Panel (P5)
as shown.
Secure the panels together by inserting 4 x Cam Nuts (H2) into Long Shelf (P6)
and tighten by turning clockwise with the
Phillips Head Screwdriver.

4
(P7)
(P3)
Align and attached the assembled frame (P4, P5, P6) onto Bottom Panel (P2).
Secure together by inserting 4 x Cam Nuts (H2) into the Left Panel (P4) and Middle Panel (P5)
and tighten by turning clockwise with the Phillips Head Screwdriver.
Slide 1 x Long Back Panel (P7) into the grooves on the Left and Middle Panel (P4, P5)
until it slots into the groove on the Bottom Panel (P2).
lign and attach Right Panel (P3) onto Bottom Panel (P2). Secure together by inserting
2 x Cam Nuts (H2) into Right Panel (P3) and tighten by turning clockwise with the
Phillips Head Screwdriver.

Page 8
7
8
Slide the Short Back Panel (P8) into the grooves on the Middle Panel (P5),
Right Panel (P3) and Bottom Panel (P2).
Slide 1 x Long Back Panel (P7) into the grooves on the Left Panel (P4) and
Middle Panel (P5).
Insert 6 x Dowels (H3) into Top Panel (P1) and secure 6 x Cam Bolts (H1) to
Top Panel (P1) by tightening with the Phillips Head Screwdriver.
(P7) (P8)
6 x Cam Bolts
(H1)
6 x Dowels
(H3)
Phillips Head
Screwdriver

Page 9
9
10
With assistance, align and attach the Top Panel (P1) to the assembled frame (P4, P5, P6).
Secure together by inserting 6 x Cam Nuts (H2) into the
Left Panel (P2), Middle Panel (P5) and Right Panel (P3) and tighten by turning clockwise
with the Phillips Head Screwdriver.
Secure 4 x Hinges (H4) to the Left Door (P9) and Right Door (P10) using
8 x Short Screws (H5), tightening with the Phillips Head Srewdriver.
6
4 x Hinges
(H4)
8 x Short Screws
(H5)
Phillips Head
Screwdriver
(P9)
(P10)

Page 10
11
12
Secure the Left Door (P9) to the Left Panel (P4) using 8 x Short Screws (H5),
tightening with the Phillips Head Screwdriver.
Repeat this step to secure the Right Door (P10) to the Middle Panel(P5).
Attach 1 x Handle (H20) to the Left Door (P9) using 2 x Short Screws (H5),
tightening using the Phillips Head Screwdriver.
Repeat this step to attach the other Handle to Right Door (P10).
16 x Short Screws
(H5)
4 x Short Screws
(H5)
Phillips Head
Screwdriver
2 x Handle
(H20)
H 6 H 6
H 2 0 H 2 0
(P4) (P5)
(P9) (P10)