fantastic furniture Tiffany User manual

Version 1.1
fantasticfurniture.com.au
King Bed
Tiffany

fantasticfurniture.com.au Page 2Page 2
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture
fantasticfurniture.com.au
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!

Assembly checklist
Useful information
Read through the instructions carefully
before you begin.
Identify and lay out all of the components
before you begin assembly.
! Never use power tools unless specifically instructed. They can damage your components or
hardware if used incorrectly.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Periodically check and re-tighten all fasteners. Check the product care label or website for
product care instructions.
! Never use any glue until you are certain that the parts belong together.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they will be
used as they may not fit through a door once assembled.
! Always use a soft surface (such as carpet or cardboard) when assembling your product to
avoid scratching or damaging the surface of the product.
! The most common mistakes made during assembly are using the wrong hardware or getting
components back to front.
Unless instructed, do not fully tighten screws
until the item is fully assembled.
Make sure you have all the required tools.
Never use power tools unless instructed.
! Please see page 2 for any safety requirements or weight restrictions.
Page 3
fantasticfurniture.com.au

What you need
to assemble the product
fantasticfurniture.com.au Page 4
Headboard
(P1)
Wing
(P2-R)
Wing
(P2-L)
Footboard
(P3)
Side Rail (P4)
Side Rail (P4)
Headboard Leg (P5)
Footboard Leg (P6)
Timber Cross Rail
(P9)
Centre Rail (P7)
Support Leg (P8)
Support Leg (P8)
28 x End Connectors (P10) 14 x Centre Connectors (P11)
28 x Slats (P12)
Footboard (P3) ; Side Rail (P4) ; Headboard Legs (P5) ; Footboard Legs (P6) ;
Box 1 :
Parts list
Centre Rail (P7) ; Support Legs (P8) ; Timber Cross Rail (P9) ; End Connectors (P10) ;
Box 2 : Headboard (P1) ; Wing (P2-L) ; Wing (P2-R) ; Slats (P12)
(Bolt)
8 x M8 x 18mm
(H1)
1 x M5 (Allen Key)
(H2)
(Bolt)
4 x M8 x 45mm
(H3)
(Washer)
10 x M8 x 19mm
(H4)
(Bolt)
6 x M8 x 25mm
(H5)
(Large Screw)
4 x M4 x 51mm
(H6)
(Felt Pad)
1 x 40 x 20mm
(H7)
(Small Screw)
2 x M4 x 32mm
(H8)
Other tools you need:
Phillips head screwdriver;
Hardware pack
Centre Connectors (P11) ; Hardware Pack

fantasticfurniture.com.au Page 5
Attach Wing (P2-L;P2-R) to the headboard (P1) with 4 x washers (H4) and
4 x Bolt 45mm (H3) by using Allen key (H2) as shown.
Attach Headboard legs (P5) to the bottom of headboard (P1) as shown.
(P1)
(P2-R)
(P1)
(P2-L)
(H2) (H3)
(H4)
(P1)
(P5)
(P5)
You will need
Allen Key
(H2)
4 x Bolts 45mm
(H3)
4 x Washers M8
(H4)
Step 1
Step 2

fantasticfurniture.com.au Page 6
Attach footboard leg (P6) to the bottom of footboard (P3)
with 4 x Large Screw 51mm (H6) by using phillips head screwdriver (not provided).
Install the bolts (H1) to the brackets by using Allen key (H2) as shown, do not tighten the bolts
and keep them 8 mm loose. Then attach side rails (P4) to headboard (P1) and footboard (P3)
by slotting the bracket on the side rails (P4) over the bolt as shown. No need to tighten bolts
until step 8 .
(P3)
(P6)
(H6)
4 x Large Screws 51mm
(H6)
Phillips head Screwdriver
(not provided)
(P3)
(P1)
(P4)
(P4)
(H1)
(H2)
You will need
Step 3
You will need
8 x Bolts 18mm
(H1) (H2)
Allen Key
Step 4

fantasticfurniture.com.au Page 7
Attach the support legs (P8) to the centre rail (P7) using 2 x Bolts (H5), 2 x Washers (H4)
as shown.
Adjust to be 10mm gap from floor
to the bottom of support legs.
Slot the centre raill (P7) into the headboard (P1) and footboard (P3)
Rotate bolts (H5) by using phillips head screwdriver (not provided) to the headboard (P1)
and footboard (P3). No need to tighten bolts until step 8 .
(P7)
(P8)
(H5)
(H4)
(P1)
(P3)
(P4)
(P4)
(P7)
(P7)
(H5)
(H4)
You will need
4 x Washers M8
(H4) 4 x Bolts 25mm
(H5)
Phillips head
Screwdriver
You will need
2 x Washers M8
(H4) 2 x Bolts 25mm
(H5)
Phillips head
Screwdriver
Step 5
Step 6

fantasticfurniture.com.au Page 8
Push 2 End Connectors (P10), 2 pcs Slats (P12)
and a Centre Connector (P11) together.
(P10) (P10)
(P11)
(P12) (P12)
Insert the full slat into the side rail and centre rail one by one.
Sometimes it make it easier to line up the
hole if you press down in the middle of the
slat to flatten it out.
You will need
28 x End
Connectors
(P10)
14 x Centre
Connectors
(P11)
28 x Slats
(P12)
1
2
3
Step 7

fantasticfurniture.com.au Page 9
Repeat for every bed slat until finished.
Make sure the inner space is square.
Attach the felt pad (H7) to the centre of centre rail (P7).
Then attach the timber cross rail (P9) to the centre of side rails (P4) by using 2 x screws (H8).
Now tighten all the bolts on the centre rail (P7) and tighten bolts on the headboard (P1)
and footboard (P3).
You will need
2 x Screws 32mm
(H8)
Phillips head
Screwdriver
(not provided)
(H2)
Allen Key Felt Pad
1 x 40 x 20mm
(H7)
(P9)
(P7)
(H7)
(H2)
(H8)
(P9)
Make sure small
screw is tighten.
4
Step 8

fantasticfurniture.com.au Page 10
Job complete!
In the interest of our environment please dispose
of all packaging thoughtfully.
Step 9