fantastic furniture Cosmic User manual

Cosmic
Bunk Twin Metal
Version 1.1

4 x End Panels (P1)
3 x Top Posts (P2)
1 x Top Post (P3)
1 x Front Guard (P4)
1 x Back Guard (P5)
42 x Slats (P6)
4 x Mid Post (P7)
4 x Lower Posts (P8)
1 x Side Rail (P9)
1 x Side Rail (P10)
1 x Ladder (P11)
End
Panel(P1)
Top Post
(P2)
Top Post
(P2)
Top Post
(P2)
Top Post
(P3)
Side Rail
(P10)
Back Guard
(P5)
Slats
(P6)
Mid Post
(P7)
Lower Post
(P8)
Lower Post
(P8)
End Panel
(P1)
Lower Post
(P8)
Lower Post
(P8)
Side Rail
(P9)
Front Guard
(P4)
Ladder
(P11)
27 x Small Bolts
(H1) 4 x Medium Bolts
(H2)
16 x Large Bolts
(H3)
84 x Connectors
(H4)
8 x Foot Endcaps
(H5)
1 x Allen Key
(H6)
Mid Post
(P7) End
Panel(P1)
End
Panel(P1)

Step 1
Step 2
(P8)
(P8)
(P1) (P1)
(P8)
(P8)
(P7)
(P7)
(P7)
(P7)
(P1)
(P8)
(P8)
(P7)
(P7)
(P7)
(P8)
(P8)
(P9)
(P10)
8 x Large Bolts
(H3)
(H3)
(H3)
1 x Allen Key
(H6)
(H6)
8 x Small Bolts
(H1)
1 x Allen Key
(H6)
(H1)
(H1)
Insert 4 x Mid Posts (P7) into 4 x Lower Posts (P8), then attach these to 2 x End Panels (P1) using 8 x Large Bolts (H3) to
connect, tightening with Allen Key (H6) to 70%, do not fully tighten yet. Note the direction of the holes for Lower post.
Attach the Side Rails (P9 & P10) to the Lower Posts (P8) using 8 x Small Bolts (H1), tightening with Allen Key (H6) to 70%, do not
fully tighten yet. Note the location of the hole for Side Rail (P9) is facing outwards and is on the right, this is important for upcoming
ladder attachment.
You will need:
You will need:

Step 3
Step 4
6
(P6)
x42
84 x Connectors
(H4)
(H4)
(H4)
Attach the 84 x Connectors (H4) to the 42 x Slats (P6).
Attach the 21 x Slats (P6) to Side Rails (P9 & P10).
You will need to press down firmly for the connectors to slot into the holes on the side rails.
(P9 )
(P10 )
You will need:

7
Step 5
Step 6
(P2)
(P5)
(P4)
(H3)
Attach the 2 x End Panels (P1) to posts (P2 & P3) using 8 x Large Bolts (H3) to connect, tightening with the Allen Key (H6) to
70%, do not fully tighten yet.
Please note the location of the holes on the Front Guard Rail is facing outwards, this is for upcoming ladder attachment.
Attach the Front Guard Rail (P4) to the Top Posts (P2 & P3) using 5 x Small Bolts (H1), tightening with the Allen Key (H6) to 70%, do
not fully tighten yet.
Attach the Back Guard Rail (P5) to the 2 x Top Posts (P2) using 6 x Small Bolts (H1), tightening with the Allen Key (H6) to 70%, do not
fully tighten yet.
(P2)
(P5)
(P4)
(H1)
(H1)
(H1)
(P2)
(P2)
(P3)
11 x Small Bolts
(H1)
1 x Allen Key
(H6)
1 x Allen Key
(H6)
8 x Large Bolts
(H3)
(H3)
(P3)
(P2)
(P2)
(P1)
(P1)
You will need:
You will need:

Step 7
Step 8
8
8 x Small Bolts
(H1)
1 x Allen Key
(H6)
(H1) (H6)
Attach the 21 x Slats (P6) to Front Guard Rail (P4) and Back Guard Rail (P5).
You will need to press down firmly for the connectors to slot into the holes on the side rails.
With two people, carefully lift the top bed into position.
Connect the upper bed to the Mid Posts (P7) using 8 x Small Bolts (H1), tightening with Allen Key (H6) to 70%, do not fully
tighten yet.
(P4)
(P5)
(P7)
(P7)
(P2)
(P2)
(P2)
(P3)
Note the location of holes for ladder.
Note the location of holes for ladder.
You will need:

Step 9
Step 10
9
(P11)
Job Complete!
In the interest of our environment please dispose of all packaging thoughtfully.
1 x Allen key
(H6)
4 x Medium Bolts
(H2)
(H2)
(H2)
(H6)
Attach Ladder (P11) to the bunk using 4 x Medium Bolts (H2), tightening with Allen Key (H6).
Important: Now fully tighten all bolts on the bunk.
You will need:

Step 11
10
Step 12
1 x Allen Key
(H6)
(H2)
(H6)
1 x Allen key
(H6)
(H6)
(H6)
Remove the Ladder (P11) from the bunk by loosening and removing all Medium Bolts (H2) with the Allen Key (H6).
Loosen and remove the Small Bolts (H1) in the Top Posts (P2 & P3) with the Allen Key (H6).
With two people, you can then carefully lift the top bed off the Mid Posts (P7).
You will need:
You will need: