fantastic furniture HAVANA User manual

HAVANA
Buffet 2 Door
www.fantasticfurniture.com.au
Version 1.1

Enjoy
Your purchase from
Australia’s Best Value Furniture Store
www.fantasticfurniture.com.au PAGE 2

Assembly checklist
Useful Information
www.fantasticfurniture.com.au PAGE 3
Read through the instructions carefully
before you begin.
Identify and lay out all of the components
before you begin assembly.
! Never use power tools unless specifically instructed. They can damage your components or
hardware if used incorrectly.
! If you are having any difficulties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Periodically check and re-tighten all fasteners. Check the product care label or website for
product care instructions.
! Never use any glue until you are certain that the parts belong together.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they will be
used in as they may not fit through a door once assembled.
! Always use a soft surface (such as carpet or cardboard) when assembling your product to
avoid scratching or damaging the surface of the product.
! The most common mistakes made during assembly are using the wrong hardware or getting
components back to front.
Unless instructed, do not fully tighten screws
until the item is fully assembled.
Make sure you have all the required tools.
Never use power tools unless instructed.

4 x Hinges
(H17)
24 x Timber
Screws
(H18)
1 x Double
Ended
Screws
(H19)
Left Drawer
Side
(P18)
Right
Drawer Side
(P19)
Drawer Back
(P21)
Drawer
Base
(P20) Drawer
Front
(P17)
Top Panel
(P1)
Back
Panels
(P13)
Side
Panel
(P7)
Side
Panel
(P7)
Bottom
Panel
(P2)
Left
Divider
(P3)
Adjustable
Shelf Panel
(P6)
Shelf Panel
(P5)
X-crossing
Board
(P8)
LR Leg
(P11)
RR Leg
(P12)
RF
Leg
(P10)
LF Leg
(P9)
Right
Divider
(P4)
Left
Door
(P15)
Right
Door
(P16)
Support
Leg
(P14)
16 x Dowels
(H1)
16 x Small
Dowels
(H2)
4 x Long
Screws
(H12)
8 x Small
Screws
(H5)
26 x Cam
Bolts
(H3)
26 x Cam
Nuts
(H4)
4 x Small
Cam Nuts
(H11)
4 x Small
Cam Bolts
(H10)
5 x Plastic
Glides
(H14)
3 x Handles
(H15)
6 x Round
Head Bolts
(H16)
1 x CL Runner
Tracks
(H6)
1 x CR Runner
Tracks
(H7)
1 x DL
Runners
(H8)
1 x DR
Runners
(H9)
6 x Inside
Hexagonal
Screws
(H13)
1 x Allen
Key
(H20)
8 x Shelf
Pin
(H21)
LF : Left Front
LR : Left Rear
RF : Right Front
RR : Right Rear
What you need
to assemble the product
Other tools you need
Flat head screwdriver; Phillips head
screwdriver; Hammer
Parts list
Box 1:Top Panel (P1);
Bottom Panel (P2);
Left Divider (P3);
Right Divider (P4);
Shelf Panel (P5);
Adjustable Shelf Panel (P6);
Side Panel (P7); X- crossing Board (P8)
LF Leg (P9); RF Leg (P10); LR Leg (P11);
RR Leg (P12); Back Panel (P13);
Support Leg (P14);
Left Door (P15); Right Door (P16);
Drawer Front (P17); Left Drawer Side (P18);
Right Drawer Side (19); Drawer Base (P20);
Drawer Back (P21);
www.fantasticfurniture.com.au PAGE 4
DO NOT USE
2 x Rubber
Stickers
(H22)

(P1)
(P3)
(P4)
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H5
H5
H5
H7
H6
H5
H6
CL
H5
H7
CR
H5
(P12)
(P11)
(P10)
(P9)
H3 H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
Attach 4 x Cam Bolts (H3) into Dividers (P3, P4).
Attach 1 x CL Runner Tracks (H6) and 1 x CR Runner Tracks (H7)
to Dividers (P3, P4) with 4 x Small Screws (H5).
Tighten the cam bolts and screws using a Phillips head screwdriver.
Attach 10 x Cam Bolts (H3) into Top Panel (P1).
Attach 12 x Cam Bolts (H3) into Legs (P9, P10, P11, P12).
Tighten Cam Bolts using a Phillips head screwdriver.
22 x Cam Bolts
(H3)
You will need
Step 1
Phillips head
screwdriver
www.fantasticfurniture.com.au PAGE 5
1 x CL Runner
Tracks (H6)
1 x CR Runner
Tracks (H7)
You will need
Step 2
4 x Small
Screws (H5)
Phillips head
screwdriver
4 x Cam Bolts
(H3)

(P5)
(P4)
(P3)
H4 H4
H4
H4
H2
H2
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
Insert 4 x Small Dowels (H2) and 4 x Cam Nuts (H4) into the holes of Shelf Panel (P5) as shown.
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Dividers (P3, P4) to Shelf Panel (P5),
then tighten the cam nuts using a Flat head screwdriver.
www.fantasticfurniture.com.au PAGE 6
4 x Small
Dowels (H2)
You will need
Step 3
4 x Cam Nuts
(H4)
Flat head
screwdriver
(P2)
(P10)
(P9)
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
H1
H1
H4
H4
H1
H1
Insert 4 x Dowels (H1) into Bottom Panel (P2).
Insert 2
x Cam Nuts (H4) into place as shown.
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Legs (P9, P10) to Bottom Panel (P2),
then tighten the cam nuts using a Flat head screwdriver.
Opposite back panel slot
face toward bottom
PVC banding
You will need
Step 4
2 x Cam Nuts
(H4)
4 x Dowels
(H1)
Flat head
screwdriver

(P7)
(P2)
(P7)
Insert 4 x Dowels (H1) into Bottom Panel (P2).
Insert 2
x Cam Nuts (H4) into the holes of Bottom Panel (P2) as shown.
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Legs (P11, P12) to Side Panels (P7),
then tighten the cam nuts using a Flat head screwdriver.
www.fantasticfurniture.com.au PAGE 7
You will need
Step 6
2 x Cam Nuts
(H4)
4 x Dowels
(H1)
Flat head
screwdriver
(P10)
(P9)
H4
Insert 8 x Cam Nuts (H4) into Side Panels (P7).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Side Panels (P7) to Legs (P9, P10),
then tighten the cam nuts using a Flat head screwdriver.
8 x Cam Nuts
(H4) Flat head
screwdriver
You will need
Step 5
H4
(P2)
(P7)
(P7)
(P11)
(P12)
H14
H1
H1
H4
H4
H4
H4
H4
H4
H4

(P13)
(P11)
(P12)
(P3)
(P4)
(P7)
(P7)
Slide Back Panels (P13) into the slot at back of unit as shown,
ensuring panels fit into groove in Bottom Panel (P2).
(P3)
(P4)
H13
H2
H2
H13
H13
H20
H13
H13
H13
1 x Allen
Key (H20)
6 x Inside
Hexagonal
Screws (H13)
You will need
Step 7
Step 8
www.fantasticfurniture.com.au PAGE 8
Groove facing up
Insert 4 x Small Dowels (H2) into Dividers (P3, P4).
Attach Dividers (P3, P4) and Side Panels (P7) to Bottom Panel (P2) with
6 x Inside Hexagonal Screws (H13) using Allen Key (H20).
Attach Support Leg (P14) to Bottom Panel (P2) with 1 x Double Ended Screws (H19),
then hammer 5 x Plastic Glides (H14) on Legs (P9, P10, P11, P12) and Support Leg (P14).
5 x Plastic
Glides (H14)
1 x Double Ended
Screws (H19)
Hammer
(P2)
(P14)
(H19)
H14
H14
H14
H14
H14
4 x Small
Dowels (H2)

H1 H1
H1 H1
H1
H1
H1 H1
(P3)
(P4)
www.fantasticfurniture.com.au PAGE 9
You will need
Step 10
10 x Cam Nuts
(H4)
8 x Small
Dowels (H2)
Flat head
screwdriver
Insert 8 x Dowels (H1) into Legs (P9, P10, P11, P12).
You will need
Step 9
8 x Dowels
(H1)
(P7)
H4
H2
H4
H4
H2
H2
H2
H4
H4
H4
H4
(P1)
Insert 8 x Small Dowels (H2) into Dividers (P3, P4) and Side Panels (P7).
Insert 10 x Cam Nuts (H4) into the holes of Dividers (P3, P4) and Legs (P9, P10, P11, P12).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Top Panel (P1) and tighten the cam nuts using a Flat head screwdriver.

(P17)
(P20)
(P18)
(P18)
(P19)
(P19)
H11
H11
H11
H11
(P17)
H10 H10
H10 H10
Slide Drawer Base (P20) into the groove
in Drawer Sides (P18) and (P19).
Insert 4 x Small Cam Nuts (H11) into the holes of Drawer Sides (P18, P19).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push
Drawer Sides (P18, P19) into place and tighten the cam nuts using a Flat head screwdriver.
PAGE 10www.fantasticfurniture.com.au
You will need
4 x Small Cam
Nuts (H11)
Step 12
Step 13
Flat head
screwdriver
Screw 4 x Small Cam Bolts (H10) into Drawer Front (P17) with a Phillips head screwdriver.
Phillips head
screwdriver
4 x Small Cam
Bolts (H10)
You will need
Step 11