fantastic furniture Java Buffet 3 Door User manual

Version 1.0
Java
Buet 3 Door
fantasticfurniture.com.au
Required
Two People

fantasticfurniture.com.au Page 2
Warning: Ensure the wall strap is attached
to avoid serious injury
To avoid any serious or fatal injury, a wall strap has been provided with
this product to prevent toppling. We strongly recommend that this
product is permanently fixed to the wall or other suitable surface. Fixing
of what fixing device to use.
Rattan
Rattan is a natural material that will respond to humidity in the
environment. Low humidity may cause the rattan to shrink.
High humidity may cause the rattan to absorb moisture and expand,
causing the weaving to look loose and wavy.
This is a natural phenomenon and not a defect.
Looks like you’ve found
your Fantastic!
Love it? Share it!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!
Fantastic buy! Share how it looks at home on Instagram
for your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture

Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
!Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
!The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
!Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
!Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
!Never use any glue until you are certain that the parts belong together.
!Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
!If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
!Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au Page 3

Parts list
Carton 1:
1 x Bottom Panel (P2)
4 x Legs (P9)
Carton 2:
1 x Top Panel (P1)
2 x Side Panels (P3)
1 x Left Divider Panel (P4)
1 x Right Divider Panel (P5)
3 x Shelves (P6)
1 x Back Panel (P7)
3 x Doors (P8)
Top Panel (P1)
What you need
to assemble the product
Other tools you need
Flat Head Screwdriver;
Phillips Head Screwdriver;
Mallet;
Hammer
fantasticfurniture.com.au
Page 4
Left Divider
Panel (P4)
Right
Divider
Panel (P5)
Shelf (P6)
Shelf (P6)
Shelf (P6)
Back Panel
(P7)
Door (P8)
Door (P8)
Door (P8)
Leg (P9)
Leg (P9)
Leg (P9)
Leg (P9)
Side Panel
(P3)
Bottom Panel (P2)
Side Panel
(P3)

fantasticfurniture.com.au
Page 5
Hardware Pack
16 x Cam Bolts
(H1)
16 x Cam
Nuts (H2)
16 x Dowels
(H3)
3 x Handles
(H4)
10 x Screws 16mm
(H6)
12 x Flat Washers
(H9)
8 x Spring
Washers (H10)
6 x Screws 28mm
(H11)
1 x Allen Key
(H12)
4 x Felt Feet
(H5)
8 x Bolts 55mm
(H8)
6 x Back Panel
Connectors (H7)
2 x Screws 25mm
(H14)
12 x Screws 12mm
(H15)
2 x Wall Straps
(H13)
12 x Screws 17mm
(H16)
6 x Hinges
(H17)
6 x Stoppers
(H19)
12 x Shelf Pins
(H18)
12 x Screws 12mm
(H20)

Step 1
Page 6fantasticfurniture.com.au
You will need
Attach 1 x felt foot (H5) onto each leg (P9) as shown.
Step 2
You will need
8 x Bolts
55mm (H8)
Attach 1 x leg (P9) onto bottom panel (P2) using 2 x bolts (H8), 2 x spring washers (H10)
and 2 x flat washers (H9).
Tighten the bolts with allen key (H12).
Repeat this step for the other 3 x legs (P9).
With assistance, turn the assembled frame over.
(P9)
4 x Felt Feet
(H5)
X4
H5
8 x Flat
Washers (H9)
8 x Spring
Washers (H10)
1 x Allen Key
(H12)
(P9)
H12
H8
H9
H10
(P2)
(P2)
(P9)
(P9)
(P9)
(P9)
Required
Two People

Step 3
Page 7fantasticfurniture.com.au
You will need
Step 4
You will need
(P2)
Screw 8 x cam bolts (H1) into top panel (P1), using a phillips head screwdriver.
Attach 3 x stoppers (H19) onto top panel (P1) with 6 x screws (H20) as shown,
tightening with a phillips head screwdriver.
8 x Cam Bolts
(H1)
Phillips Head
Screwdriver
8 x Cam Bolts
(H1)
Phillips Head
Screwdriver
Screw 8 x cam bolts (H1) into bottom panel (P2), using a phillips head screwdriver.
Attach 3 x stoppers (H19) onto bottom panel (P2) with 6 x screws (H20) as shown,
tightening with a phillips head screwdriver.
H1
6 x Screws
12mm (H20)
3 x Stoppers
(H19)
H1
H1
H1
H1
H1
H1
H1 H20
H19
H20
H19 H20
H19
(P2)
(P1)
H1
H1
H1
H1
H1
H1
H1
H20
H19
H20
H19
H1
H20
H19
(P1)
6 x Screws
12mm (H20)
3 x Stoppers
(H19)

Step 5
Page 8fantasticfurniture.com.au
You will need
H3
Mallet
16 x Dowels
(H3)
(P3)
Step 6
You will need
Insert 4 x dowels (H3) into each panel (P3, P4, P5) as shown.
Use a mallet to gently tap the dowels into place if needed.
X2
(P4) (P5)
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
Flat Head
Screwdriver
8 x Cam Nuts
(H2)
Position the panels (P3 x 2, P4, P5)
onto bottom panel (P2) as shown.
Ensure the grooves on
2 x side panels (P3) align with the
grooves on bottom panel (P2).
Insert 8 x cam nuts (H2) into
panels (P3 x 2, P4, P5).
Rotate the cam nuts so the arrow
faces incoming cam bolts.
Using a flat head screwdriver
turn clockwise to lock.
(P3) H2
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
(P2)
H2
H2
H2
H2
H2
(P3)
(P4)
(P5)
Laminated
edge

Step 7
Page 9fantasticfurniture.com.au
Step 8
Unfold and slide back panel (P7)
into the groove of panels (P2, P3 x 2).
(P2)
(P3)
(P3)
(P7)
You will need
Flat Head
Screwdriver
8 x Cam Nuts
(H2)
Required
Two People
With assistance,
position top panel (P1) onto
panels (P3 x 2, P4, P5).
Ensure the grooves on
the top panel (P1) align with the grooves
on the 2 x side panels (P3).
Insert 8 x cam nuts (H2) into panels (P3 x 2, P4, P5)
and lock by turning clockwise using a flat head screwdriver.
(P1)
H2
(P3)
(P4)
(P5)
(P3)
H2
H2
H2
H2 H2
H2
H2

Step 9
Page 10fantasticfurniture.com.au
You will need
Step 10
You will need
If necessary, gently adjust the top panel (P1) sideways in either direction
until XX and YY are equal.
Holding it in place, fix 6 x back panel connectors (H7) to assembled unit with 6 x screws (H6)
as shown, using a phillips head screwdriver.
Fasten back panel (P7) to divider panels with 4 x screws (H6), using a phillips head screwdriver.
Phillips Head
Screwdriver
10 x Screws
16mm (H6)
6 x Back Panel
Connectors (H7)
XX
YY
XX = YY
Required
Two People
(P7)
XX
YY
(P1)
H6
H6
H6
H6
H7
H7
H7
H7
H7
H7
(P1)
(P1)
(P7)
(P7)
H7
H7
H6
Insert 12 x shelf pins (H18) into desired holes in panels (P3 x 2, P4, P5).
Use a mallet to gently tap them into place if needed.
Place 3 x shelves (P6) onto shelf pins (H18).
12 x Shelf Pins
(H18)
(P6)
(P6)
(P6)
(P3)
(P4)
(P3)
(P5)
H18 H18
H18
H18
H18
H18 H18
H18
H18
Mallet

Step 11
Page 11fantasticfurniture.com.au
You will need
Step 12
You will need
Insert 2 x hinges (H17) onto each door (P8),
attach with 4 x screws (H15),
tightening using a phillips head screwdriver.
Attach 3 x handles (H4) to doors (P8) with 6 x screws (H11),
tightening using a phillips head screwdriver.
Phillips Head
Screwdriver
12 x Screws
12mm (H15)
6 x Hinges
(H17)
6 x Screws
28mm (H11)
X3
3 x Handles
(H4)
(P8)
H11
H15
H15
H17
H17
H15
H17 (P8)
H4
Phillips Head
Screwdriver
12 x Screws
17mm (H16)
Attach doors onto assembled unit as shown.
Fix 6 x hinges (H17) onto panels (P3) and (P5) with 12 x screws (H16),
tightening using a phillips head screwdriver.
H16
(P8)
H17
(P3)
(P3)
(P5)

Page 12fantasticfurniture.com.au
TO ADJUST YOUR DOORS TO MAKE THE GAPS MORE EVEN (OPTIONAL).
STEP 1
Open the door.
gap too large gap too small
STEP 2a MOVE DOOR OUT STEP 2b MOVE DOOR IN
STEP 3a MOVE DOOR LEFT STEP 3b MOVE DOOR RIGHT
STEP 2
STEP 3
Top panel
Side
panel
Door
Slightly pull the hinge forward. Slightly push the hinge back.
Slightly turn the screw clockwise
to make the gap smaller.
Slightly turn the screw
counterclockwise to make the gap
larger.
Adjust the door panel to be flush
with side panel and top panel edge.
Slightly loosen the screw indicated
and adjust the hinge to the desired
position (see step 2a & 2b), then
tighten the screw with a phillips
head screwdriver.
Adjust the gap between door panel
and side panel.
Slightly loosen or tighten
the screw indicated and adjust
the hinge to the desired position
(see step 3a & 3b).
Door
Side
panel
Top panel
Top panel
DoorDoor
Door
Door
Top panel Top panel
Side
panel
Side
panel
Door
Top panel
Side
panel Top panel
Door
Top panel
Door
Top panel
Door
Top panel
Door
Side
panel
Side
panel

Step 13
Page 13fantasticfurniture.com.au
You will need
Step 14
You will need
Fasten 2 x wall straps (H13) on top panel (P1)
with 2 x screws (H14) and 2 x flat washers (H9),
tighten using a phillips head screwdriver.
2 x Flat
Washers (H9)
2 x Screws
25mm (H14)
Phillips Head
Screwdriver
2 x Wall Straps
(H13)
(P1)
H13
H9
H14
(P1)
We strongly recommend that
this product is permanently fixed to
the wall or other suitable surface.
2 x Flat
Washers (H9)
Phillips Head
Screwdriver
Two People
Seek advice from a qualified
trades person on how to
attach this wall strap to
your specific wall.
Screw and wall plug are not included.
Please use appropriate fixtures for your wall.
With assistance, move the buet to the final position.
Attach the wall straps to the wall with the appropriate fixtures.
Make sure they are firmly attached and secure.
Wall
H13
H9

Step 15
Page 14fantasticfurniture.com.au
Job complete!
In the interest of our environment please dispose
of all packaging thoughtfully.