fantastic furniture HAYMAN User manual

HAYMAN
Cabinet 2 Door
TEMPERED GLASS SHOULD ALWAYS BE HANDLED WITH CARE
www.fantasticfurniture.com.au
Version 1.0

Enjoy
Your purchase from
Australia’s Best Value Furniture Store
www.fantasticfurniture.com.au PAGE 2

Assembly checklist
Useful Information
www.fantasticfurniture.com.au PAGE 3
Read through the instructions carefully
before you begin.
Identify and lay out all of the components
before you begin assembly.
! Never use power tools unless specifically instructed. They can damage your components or
hardware if used incorrectly.
! If you are having any difficulties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Periodically check and re-tighten all fasteners. Check the product care label or website for
product care instructions.
! Never use any glue until you are certain that the parts belong together.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they will be
used in as they may not fit through a door once assembled.
! Always use a soft surface (such as carpet or cardboard) when assembling your product to
avoid scratching or damaging the surface of the product.
! The most common mistakes made during assembly are using the wrong hardware or getting
components back to front.
Unless instructed, do not fully tighten screws
until the item is fully assembled.
Make sure you have all the required tools.
Never use power tools unless instructed.

Top Panel
(P1) Right Side
Panel
(P3)
Left Side
Panel
(P2)
Shelf Panel
(P5)
Shelf Panel
(P14)
Bottom Panel
(P6)
Rail
(P4)
Right Door
(P11)
Left Door
(P10)
Support Leg
(P12)
Back Panel
(P8)
Rail
(P9)
Divider
(P7)
10 x Dowels
(H1)
18 x Timber
Screws
(H5)
4 x Hinges
(H6)
2 x Magnetic
Bars
(H7)
16 x Cam Bolts
(H3)
16 x Cam Nuts
(H4)
2 x Handles
(H11)
2 x Bolts
(H12)
4 x
Screws
(H13)
4 x Screws
(H8)
What you need
to assemble the product
Other tools you need
Flat head screwdriver;
Phillips head screwdriver;
Parts list
Box 1: Top Panel (P1); Left Side Panel (P2);
Right Side Panel (P3); Rail (P4);
Shelf Panel (P5); Bottom Panel (P6);
Divider (P7); Back Panels (P8);
Rail (P9); Left Door (P10);
Right Door (P11); Support Leg (P12);
Back Panel (P13); Shelf Panel (P14);
www.fantasticfurniture.com.au PAGE 4
DO NOT USE
8 x Shelf Pins
(H10)
2 x Magnetics
(H9)
2 x Long Screws
(H2)
1 x Screw
(H15)
1 x Safety
Strap
(H14)
2 x Washers
(H16)
Safety
Strap Set
Back Panel
(P13)

This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
www.fantasticfurniture.com.au PAGE 5
Step 1
2 x Cam Nuts
(H4)
Flat head
screwdriver
Insert 4 x Dowels (H1) into Side Panels (P2, P3).
Attach 8 x Cam Bolts (H3) into Side Panels (P2, P3) as shown.
4 x Dowels
(H1)
You will need
8 x Cam Bolts
(H3)
Phillips head
screwdriver
Step 2
You will need
2 x Cam Bolts
(H3)
Phillips head
screwdriver
H3
H1
H3
H4
H3
H3 H3
H3
H3
H3 H3
H1
(P2)
(P4)
(P4)
(P6)
(P3)
Attach 2 x Cam Bolts (H3) into Rail (P4) as shown.
Insert 2 x Cam Nuts (H4) into the holes of Bottom Panel (P6).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Rail (P4) to Bottom Panel (P6), then tighten the cam nuts.
Bottom is flash.
H1
H3
H4

www.fantasticfurniture.com.au PAGE 6
4 x Cam Nuts
(H4)
Flat head
screwdriver
You will need
Step 3
4 x Cam Nuts
(H4)
Flat head
screwdriver
You will need
Step 4
Insert 4 x Cam Nuts (H4) into the holes of Bottom Panel (P6) and Rail (P9).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Bottom Panel (P6) and Rail (P9) to Left Side Panel (P2), then tighten the cam nuts.
Put Back Panel (P13) into the groove of Bottom Panel (P6) and Rail (P9).
Insert 4 x Cam Nuts (H4) into the holes of Bottom Panel (P6) and Rail (P9).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push Right Side Panel (P3) into place and tighten the cam nuts.
(P2)
(P9)
(P6)
H4
H4
H4
H4
(P2)
(P9)
(P13)
(P6)
(P3)
H4
H4
H4
H4

www.fantasticfurniture.com.au PAGE 7
Put Back Panel (P8) into the groove of Side Panels (P2, P3) and Rail (P9).
H1
H2
H2
H13
H13
H1
4 x Screws
(H13)
Phillips head
screwdriver
You will need
Step 5
Step 6 (P8)
(P2)
(P3)
(P2)
(P7)
(P6)
(P12)
(P3)
2 x Dowels
(H1)
2 x Long
Screws
(H2)
Insert 2 x Dowels (H1) into the holes of Divider (P7).
Attach Divider (P7) to Bottom Panel (P6) with 2 x Long Screws (H2).
Attach Support Leg (P12) to Bottom Panel (P6) with 4 x Screws (H13) as shown.

(P7)
H4
H1
H4
H4
H4
H4
Insert 4 x Dowels (H1) into the holes of Side Panels (P2, P3).
Insert 6 x Cam Nuts (H4) into the holes of Side Panels (P2, P3) and Divider (P7).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Top Panel (P1) and tighten the cam nuts.
(P1)
(P2)
(P3)
4 x Screws
(H8)
www.fantasticfurniture.com.au PAGE 8
2 x Magnetics
(H9)
H9
6 x Cam Nuts
(H4)
You will need
Step 8
Flat head
screwdriver
Attach 6 x Cam Bolts (H3) into Top Panel (P1) as shown.
Attach 2 x Magnetics (H9) to Top Panel (P1) with 4 x Screws (H8).
(P1)
H3
H3
H3
H3
H3
H3
6 x Cam Bolts
(H3)
Phillips head
screwdriver
You will need
Step 7
H8
H8
H8
H8
H9
4 x Dowels
(H1)
H1

Attach 4 x Hinges (H6) and 2 x Magnetic Bars (H7) to Doors (P10, P11) with 10 x Timber Screws (H5) .
(P11)
(P10)
(P3)
(P2)
(P10)
(P11)
www.fantasticfurniture.com.au PAGE 9
H5
H6
H6
H5
Phillips head
screwdriver
You will need
Step 10
4 x Hinges
(H6)
2 x Magnetic
Bars (H7)
10 x Timber
Screws (H5)
Phillips head
screwdriver
8 x Timber
Screws (H5)
You will need
Step 9
H5
H7
H11
H11
H5
H5 H12
H12
H5 H5
H5 H5
H5
Attach Left Door (P10) to Left Side Panel (P2)
and Right Door (P11) to Right Side Panel (P3) with 8 x Timber Screws (H5).
Tighten screws using a Phillips screwdriver.
Attach 2 x Handles (H11) to Doors (P10, P11) with 2 x
Bolts (H12).
2 x Handles
(H11)
2 x Bolts
(H12)
H5
H7

(P5)
(P2)
(P14)
www.fantasticfurniture.com.au PAGE 10
Insert 8 x Shelf Pins (H10) into the holes of Side Panels (P2, P3) and Divider (P7) as shown.
Insert Shelf Panels (P5, P14) into the cabinet.
You will need
8 x Shelf Pins
(H10)
Step 11
H10
H10
(P1)
Phillips head
screwdriver
1 x Safety
Strap (H14)
1 x Screw
(H15)
You will need
Step 12
1 x Washer
(H16)
We strongly advise that you use
the wall safety strap provided to
prevent the unit toppling
Use 1 x Screw (H15) and 1 x Washer (H16) to
connect 1 x Safety Strap (H14) on Top Panel (P1).
H14
H15
H16