fantastic furniture Tiffany User manual

Version 1.2
Tiffany
fantasticfurniture.com.au
Queen Bed

fantasticfurniture.com.au Page 2Page 2
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture
fantasticfurniture.com.au
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!

Assembly checklist
Useful information
Read through the instructions carefully
before you begin.
Identify and lay out all of the components
before you begin assembly.
! Never use power tools unless specifically instructed. They can damage your components or
hardware if used incorrectly.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Periodically check and re-tighten all fasteners. Check the product care label or website for
product care instructions.
! Never use any glue until you are certain that the parts belong together.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they will be
used as they may not fit through a door once assembled.
! Always use a soft surface (such as carpet or cardboard) when assembling your product to
avoid scratching or damaging the surface of the product.
! The most common mistakes made during assembly are using the wrong hardware or getting
components back to front.
Unless instructed, do not fully tighten screws
until the item is fully assembled.
Make sure you have all the required tools.
Never use power tools unless instructed.
! Please see page 2 for any safety requirements or weight restrictions.
Page 3
fantasticfurniture.com.au

What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
Headboard
(P1)
Wing
(P2-L)
Wing
(P2-R)
Footboard
(P3)
Footboard Leg (P6)
Headboard Leg (P5)
Side Rail (P4)
Side Rail (P4)
Timber Cross Rail
(P9)
Centre Rail (P7)
Support Leg (P8)
Support Leg (P8)
fantasticfurniture.com.au Page 4
28 x End Connectors (P10) 14 x Centre Connectors (P11)
28 x Slats (P12)
Footboard (P3) ; 2 x Side Rail (P4) ; 2 x Headboard Leg (P5) ; 2 x Footboard Leg (P6) ;
Parts list
Box 1 :
Centre Rail (P7) ; 2 x Support Leg (P8) ; Timber Cross Rail (P9) ; End Connectors (P10) ;
Centre Connectors (P11) ; Hardware Pack.
Headboard (P1) ; Wing (P2-L) ; Wing (P2-R) ; Slats (P12)
Box 2 :
(Bolt)
8 x M8 x 18mm
(H1)
1 x M5 (Allen Key)
(H2)
(Bolt)
4 x M8 x 45mm
(H3)
(Washer)
10 x M8 x 19mm
(H4)
(Bolt)
6 x M8 x 25mm
(H5)
(Large Screw)
4 x M4 x 51mm
(H6)
(Small Screw)
2 x M4 x 32mm
(H8)
1 x 40 x 20mm
(H7)
(Felt Pad)
Hardware pack

Step 1
You will need
Allen Key
(H2)
4 x Washers M8
(H4)
4 x Bolts 45mm
(H3)
(P1)
(P2-R)
(P1)
(P2-L)
(H3)
(H2) (H4)
Attach wings (P2-L ; P2-R) to the headboard (P1) with 4 x washers (H4) and
4 x bolts 45mm (H3) by using allen key (H2) as shown.
Step 2
(P1)
(P5)
(P5)
Attach 2 x headboard legs (P5) to the bottom of headboard (P1) as shown.
fantasticfurniture.com.au Page 5

Step 3
You will need
4 x Large Screws 51mm
(H6)
Phillips head
Screwdriver
(not provided)
(P3)
(P6)
(H6)
Attach 2 x footboard legs (P6) to the bottom of footboard (P3)
with 4 x large screw 51mm (H6) by using phillips head screwdriver (not provided).
Step 4
You will need
8 x Bolts 18mm
(H1) (H2)
Allen Key
(P3)
(P4)
(P4)
(P1)
(H1)
(H2)
fantasticfurniture.com.au Page 6
Install the bolts (H1) to the brackets by using allen key (H2) as shown, do not tighten the
bolts and keep them 8mm loose. Then attach 2 x side rails (P4) to headboard (P1) and
footboard (P3) by slotting the bracket on the side rails (P4) over the bolt as shown.
No need to tighten bolts until step 8.

Step 5
You will need
2 x Washers M8
(H4)
2 x Bolts 25mm
(H5)
Phillips head
Screwdriver
(not provided)
(H5)
(H4)
(P7)
(P8)
Attach 2 x support legs (P8) to the centre rail (P7) using 2 x bolts (H5) and 2 x washers (H4)
as shown.
Step 6
You will need
4 x Washers M8
(H4)
4 x Bolts 25mm
(H5)
Phillips head
Screwdriver
(not provided)
(H4) (H5)
(P7)
(P7)
(P1)
(P3)
(P4)
(P4)
Adjust to be 10mm gap from floor
to the bottom of support legs.
Slot the centre rail (P7) into the headboard (P1) and footboard (P3).
Rotate bolts (H5) by using phillips head screwdriver (not provided) to the headboard (P1)
and footboard (P3). No need to tighten bolts until step 8.
fantasticfurniture.com.au Page 7

Step 7
You will need
28 x End
Connectors
(P10)
14 x Centre
Connectors
(P11)
28 x Slats
(P12) Push 2 end connectors (P10), 2 pcs slats (P12)
and a centre connector (P11) together.
(P10) (P10)
(P11)
(P12) (P12)
Insert the full slat into the side rail and centre rail one by one.
Sometimes it makes it easier to line up the
hole if you press down in the middle of the
slat to flatten it out.
fantasticfurniture.com.au Page 8
1
2
3

Repeat for every bed slat until finished.
Step 8
(P9)
(H7)
(P7)
(P9)(H8)
(H2) Make sure small
screw is tightened.
Make sure the inner space is square.
Attach the felt pad (H7) to the centre of centre rail (P7).
Then attach the timber cross rail (P9) to the centre of side rails (P4) by using 2 x screws (H8).
Now tighten all the bolts on the centre rail (P7) and tighten bolts on
the headboard (P1) and footboard (P3).
fantasticfurniture.com.au Page 9
4
Felt Pad
1 x 40 x 20mm
(H7)
You will need
2 x Small Screws 32mm
(H8)
(H2)
Allen Key
Phillips head
Screwdriver
(not provided)

Step 9
Job complete!
In the interest of our environment please dispose
of all packaging thoughtfully.
fantasticfurniture.com.au Page 10