Heat & Glo Tonic SLR-C User manual

1
Heat & Glo • Tonic Decorative Front Instructions • 2143-904 Rev. C • 5/16
Tonic Decorative Front
Model: SLR-C, SLR-D
Installation Instructions
Leave this manual with party responsible for use
and operation.
CAUTION! Risk of Cuts or Abrasions. Wear protective
gloves and safety glasses during installation. Sheet metal
edges are sharp.
Figure 2. Bracket Engagement
Figure 1. Location of Shoulder Bolts
WARNING! Risk of Fire! Combustible materials MUST
NOT overlap or be placed under a decorative front.
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of
burns from the hot viewing glass is provided
with this appliance and shall be installed for
the protection of children and other at-risk
individuals.
SHOULDER
BOLTS
Figure 3. Mesh Installed.
SLIDE DOWN
CONTENTS:
• Decorative Front Assembly
(Mesh brackets afxed to back side for shipment)
• Shoulder Bolts (4)
• Mesh screen assembly
Verify and remove contents from packaging before
beginning installation.
Installation Instructions
1. Install the four shoulder bolts, two per side, as shown
in Figure 1.
Note: The bolts should be threaded in 2 full turns only.
2. Remove mesh brackets from back side of decorative
front assembly. Discard screws.
3. Align mesh brackets onto the threaded section of the
shoulder bolts on each side of the replace and slide the
bracket down as shown in Figure 2.
4. Tighten bolts securely on each side of replace.
5. Place lower section of framed mesh assembly into ap-
pliance opening. Center the assembly between the
shoulder bolts and hang it on to the brackets as shown
in Figure 3.

Heat & Glo • Tonic Decorative Front Instructions • 2143-904 Rev. C • 5/16
2
6. Install the door into the replace opening. Note the
orientation of the door brackets. The slots in the
bracket will only line up with the shoulder bolts in the
replace if the door is installed correctly. See gure 4.
7. Push the front toward the replace, ensuring it ts
tightly to the nish material.
A
B
D
C
EF
Figure 5. Dimensions of Tonic Decorative Front.
Table 1. Dimensions of Tonic Decorative Front
(TON-SLR-**)
DIMENSION TON-SLR-**
ATop of decorative front to bot-
tom of appliance. 26-3/8 in. 670 mm
BBottom of decorative front to
bottom of appliance. 6-7/8 in. 175 mm
CInside dimension of decorative
front (width). 39 in. 991 mm
DOutside dimension of decora-
tive front (width). 44-1/2 in. 1130 mm
EInside dimension decorative
front (height). 13 in. 330 mm
FOutside dimension of decora-
tive front (height). 19-1/2 in. 495 mm
Figure 4. Bracket Engagement with Bolts
Please contact your Heat & Glo dealer with any
questions or concerns.
For the location of your nearest Heat & Glo dealer,
please visit www.heatnglo.com.
Heat & Glo, a brand of Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
www.heatnglo.com
Cleaning Instructions for Fronts
Use a microber cloth and Windex® Original Glass
Cleaner or 03M003 Stove Bright® Glass Cleaner to clean
the front immediately after installation to remove acids
deposited by the installer or technician. Spray the cleaner
onto the microber cloth and carefully wipe the entire
surface. The front should be cleaned in this manner
annually by the homeowner to remove ngerprints or
other contaminants. Once oxidation of the paint pigment
has occurred, cleaning will not restore the original color.