Fisher-Price SWING 'N MEALS 79739 User manual

w
w
w.
fi
s
he
r
-p
r
i
c
e
.
c
o
m
Model Number: 79739
Please keep this instruction sheet for future reference, as it contains important information.
Read all instructions BEFORE assembly and USE of product.
Adult assembly is required.
Tool needed for assembly: Phillips Screwdriver (not included).
Requires three “D” (LR20) alkaline batteries for swing operation (not included).
Maximum weight limit for swing use: 25 lbs. (11.35 kg)
IMPORTANT! The maximum weight limit for use as a swing is 25 lbs.
If your child weighs less than 25 lbs., but is really active and appears
to be able to climb out of the swing, immediately discontinue its use.
Product features and decorations may vary from the photos above.
Swing ‘n
Meals
™
It’s a swing. It’s a two-position high chair.
Use it as a traditional swing to soothe and entertain baby with
head-to-toe swinging motion and then convert it to a high chair!
Swing High Chair
79739b-0920.qrk 10/25/01 11:11 PM Page 1

Warnings
Consumer Information
2
Swing
•To prevent falls when using the swing, never use with an active child who may
be able to climb out of the seat.
•Never leave child unattended.
•To prevent serious injury or death from falls or sliding out, always use the
restraint system. Never rely on the tray to restrain child.
High Chair
Prevent serious injury or death from falls or sliding out.
•The child should be secured in the high chair at all times by the restraining sys-
tem. The restraint belts must be adjusted to fit your child snugly. The tray is not
designed to hold the child in the chair.
•Always keep child in view while in the high chair.
•Never leave child unattended.
•It is recommended that the product is used as a high chair only by children
capable of sitting upright unassisted.
WARNING
Occasionally a consumer may experience a problem with one of our products. If this should happen please call us, toll-free, rather
than return this product to the store. Usually we can solve the problem on the telephone or by sending you replacement parts.
Please call Fisher-Price®Consumer Relations, toll-free at 1-800-432-KIDS,8AM - 6 PM EST Monday through Friday. Hearing-impaired
consumers using TTY/TDD equipment, please call 1-800-382-7470.
Or, write to: Fisher-Price®Consumer Relations, 636 Girard Avenue, East Aurora, New York 14052.
79739b-0920.qrk 10/25/01 11:11 PM Page 2

Parts
3
Rear Leg with
Housing
Rear Leg with
Motor Housing
Rear Base
Front Base
2 Front Legs
Large High
Chair Tray
Small Swing Tray
Reversible Pad
Seat Frame
Seat
This package contains small parts in
its unassembled state.
Adult assembly is required.
CAUTION
#8 x 11/4" Screw – 2
SHOWN ACTUAL SIZE
79739b-0920.qrk 10/25/01 11:11 PM Page 3

Assembly
4
•Place the front base on a flat surface.
•Position a front leg so that the tapered end is downward,
as shown.
•While pressing the button on one of the front legs, insert it
into the front base. Push down on the front leg until the
button “snaps” into the hole in the front base.
•Repeat this procedure to assemble the other front leg to
the front base.
Front Base
Tapered End
Tapered End
Front Legs
IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use
if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts.
•While standing on the front base, pull the front legs up.
The front legs should remain secured to the front base.
If you can remove the front legs, you have not assembled
them correctly to the front base. Reread and repeat
assembly step 1.
•Position the rear leg with housing so that the hub is inward.
•While pressing the upper button on front leg, insert it into
the rear leg with housing slot, as shown. Push the front leg
until the button “snaps” into the hole in the rear leg with
housing.
•Repeat this procedure to assemble the rear leg with motor
housing to the other front leg.
•Pull the front legs down to be sure they are secure in the
housings. If you can remove them, you have not assembled
them correctly. Please re-read and repeat this assembly step.
•Pull both rear legs out until they “snap” into place.
Press
Button
Press
Button
Hubs
Rear Leg
with
Housing
Slot
Rear Leg
with
Motor
Housing
Front
Legs
Press
Buttons
Front Legs Pull Up
Pull Up
Pull
Rear
Leg Pull
Rear
Leg
Front Base
1
2
3
4
79739b-0920.qrk 10/25/01 11:11 PM Page 4

Assembly
5
•Place the rear base on a flat surface, as shown.
•While pressing the buttons on each side of the rear base, fit
the rear legs onto the rear base. Push the rear legs down
until the buttons on the rear base “snap” into the holes in
each rear leg.
Rear Base
Front
Base
Rear
Legs
•While standing on the rear base, pull the rear legs up.
They should remain secured to the rear base. If you can
remove the rear legs, you have not assembled them cor-
rectly to the rear base. Re-read and repeat assembly step 5.
•Set the frame assembly aside for Assembly step 8.
Press
Buttons
Rear Legs
Pull Up
Pull Up
Rear Base
5
•Position the seat frame on a
flat surface.
•Fit the hole in the seat hubs
onto the seat frame tubes.
•Press the upper buttons on
the seat frame tubes and
slide the seat down.
•Press the middle buttons on
the seat frame tubes and slide the seat down.
•Press the lower buttons on the seat frame tubes and slide
the seat down.
•The seat should be touching the footrest.
7
6
Seat
Hub
Seat Frame Tubes
Press Upper
Button
Press Middle
Button
Press Lower
Button
Press Lower
Button
Press Middle
Button
Press Upper
Button
Seat
Hub
79739b-0920.qrk 10/25/01 11:11 PM Page 5

Assembly
6
Hubs
Seat Frame Tubes
Plastic
Housing
Press Buttons
8
•Insert a screw into each hub
and each seat frame tube.
•Tighten the screws with a Phillips screwdriver. Do not
over-tighten.
Seat Frame Tubes
Hubs
Insert Screws
9
#8 x 11/4" Screw – 2
Shown Actual Size
•Decide which side of the reversible pad you will use. One
side of the pad has a soft, cotton material with ruffle (for
swing use); the other side is a wipeable vinyl material (for
high chair use).
•Fit the pocket on the back of the reversible pad onto the
seat back.
•Insert the crotch restraint through the large rectangular
opening in the pad.
10
Crotch
Restraint
Pad
•Position the frame assembly so that the curved, front base
is towards you.
•Fit the seat frame tubes into the hubs on the frame
assembly.
•Press the upper buttons on the seat frame tubes and insert
them into the hubs on the frame assembly until they “snap”
into place. Make sure you hear a “snap” on both sides.
•Fit the waist restraints through the smaller slots in the
reversible pad.
•Fasten the fasteners on the sides of the reversible pad to
the back of the seat.
•Fit the bottom edge of the reversible pad around the bot-
tom edge of the seat.
Assembly is now complete.
IMPORTANT! Before first-time use, please read and under-
stand how to install batteries, setup, use, store and care
for Swing ‘n Meals™.
11
Waist Restraints
Fastener Fastener
79739b-0920.qrk 10/25/01 11:11 PM Page 6

Battery Installation Battery Tips
7
•Locate the battery compartment on the plastic housing.
•Using a coin, press the tab on the battery compartment
door and remove it.
•Insert three, new “D” (LR20) alkaline batteries as shown in
the battery compartment.
•Replace the battery compartment door.
•Do not mix old and new batteries.
•Do not mix different types of batteries: alkaline, standard
(carbon-zinc) or rechargeable (nickel-cadmium).
•Remove the batteries during long periods of non-use.
Always remove exhausted batteries from the product.
Battery leakage and corrosion can damage this product.
Dispose of exhausted batteries properly.
•Do not dispsose of batteries in a fire.The batteries may
explode or leak.
•Never short circuit the battery terminals.
•Non-rechargeable batteries are not to be recharged.
•Only batteries of the same or equivalent type as
recommended in the Battery Installation instructions are
to be used.
•If removable rechargeable batteries are used, they are only
to be charged under adult supervision.
•Rechargeable batteries are to be removed from the toy
before they are charged.
•If you use a battery charger, it should be examined regularly
for damage to the cord, plug, enclosure and other parts.
Do not use a damaged battery charger until it has been
properly repaired.
-
+
SHOWN ACTUAL SIZE
1.5V x 3
“D” (LR20)
Battery
Compartment
Door
Hint: We recommend using alkaline batteries for longer
battery life.
Hint: When swinging motion becomes noticeably slower,
remove the batteries and replace them with three, new “D”
(LR20) alkaline batteries.
79739b-0920.qrk 10/25/01 11:11 PM Page 7

Swing and High Chair Use
8
Swing High Chair
IMPORTANT! Before each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use
if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts.
79739b-0920.qrk 10/25/01 11:11 PM Page 8

•Lift the seat and then press the buttons on the back side
of the seat tubes to release the seat .
•Lift the seat again .
B
Converting from Swing to High Chair
High Chair Setup and Use
9
1
Prevent serious injury or death from
falls or sliding out.
•The child should be secured in the
high chair at all times by the restrain-
ing system. The restraint belts must
be adjusted to fit your child snugly.
The tray is not designed to hold the
child in the chair.
•Always keep child in view while in
the high chair.
•Never leave child unattended.
•It is recommended that the product is
used as a high chair only by children
capable of sitting upright unassisted.
WARNING
Seat Tube
Press
Seat
Tube
Button
Lift
Lift
•Continue to lift the seat until it rotates forward . The
notches in the hubs will align with the plastic ridge on the
seat frame tubes.
•Again, lift the seat until it “snaps” into place.The seat is
now in the lower high chair position.
2
•For the upper high chair position, simply press the buttons
on the front side of the seat frame tubes and lift the seat
until it “snaps” into place.
3
Press
Seat
Tube
Button
B
79739b-0920.qrk 10/25/01 11:11 PM Page 9

•Pull the footrest forward.
•Locate the lock knobs on each end of the footrest.
•Pull the lock knobs down and then slide them out .The
lock symbol should be visible on both lock tab.The
footrest locks for high chair use.
•Check to be sure the seat is secure for high chair use:
- Push the seat bottom down with your hand. The seat
should not move.
- Push the footrest back.The footrest should not move.
Swing 'n Meals™is now ready for high chair use.
To tighten the waist restraints:
•Feed the anchored end of the waist restraint up through the
buckle to form a loop .
•Pull the free end of the waist restraint .
•Repeat this procedure to tighten the other waist restraint.
To loosen the waist restraints:
•Feed the free end of the waist restraint up through the
buckle to form a loop .
•Enlarge the loop by pulling on the end of the loop toward
the buckle.
•Pull the anchored end of the waist restraint to shorten the
free end of the waist belt .
•Repeat this procedure to loosen the other waist restraint.
High Chair Setup and Use
10
4
Lock Knob
Pull
Down
Push
Out
The child should be secured in the
product at all times by the restraining
system. The restraint belts must be
adjusted to fit your child snugly. The
tray is not designed to hold the child in
the chair.
WARNING
Restraint Use
•Place your child in the seat.
•Pull the crotch restraint up between your child’s legs and
fasten both waist restraints to the crotch restraint. Make
sure you hear a“snap” on both sides.
5
Hint: Choose which side of the reversible pad you would like
to use. Refer to assembly steps 10 and 11 (on page 6) to attach
the pad.
Tighten Loosen
Anchored End
Buckle
Buckle
Anchored End
Free End
Free End
Footrest
Lock
Knob
Waist Restraint Waist Restraint
Crotch Restraint
79739b-0920.qrk 10/25/01 11:11 PM Page 10