Frico Tiger User manual

Tiger 2-15 kW
Original instructions
EN This product is only suitable for well insulated spaces or occasional use.
SE Denna produkt är endast lämpad för välisolerade utrymmen eller sporadisk användning.
NO Dette produktet er bare egnet for velisolerte rom eller sporadisk bruk.
FR Ce produit ne peut être utilisé que dans des locaux bien isolés ou de manière occasionnelle.
DE Dieses Produkt ist nur für gut isolierte Räume oder für den gelegentlichen Gebrauch geeignet.
NL Dit product is uitsluitend geschikt voor goed geïsoleerde plaatsen of voor incidenteel gebruik.
FI Tämä tuote soveltuu ainoastaan hyvin eristettyihin tiloihin tai satunnaiseen käyttöön.
RU Прибор пригоден к применению в местах с достаточной степенью теплоизоляции или для периодического обогрева.
PL Ten produkt jest odpowiedni tylko do sporadycznego użytku lub do stosowania w dobrze izolowanych pomieszczeniach.
ES Este producto está indicado únicamente en lugares abrigados o para una utilización puntual.
DK Dette produkt er kun egnet til godt isolerede rum eller lejlighedsvis brug.
....8
EN .... 10 SE .... 12
NO .... 14 FR ....16 DE
....18
NL ....20 FI ....22 RU .... 24 PL .... 26 ES
....28
DK
5
kW
C
1
0

A
B
C
°C
0
1
A
B
C
°C
A
[mm]
B
[mm]
C
[mm]
TIG21, TIG31, TIG51,
TIG33, TIG53
290 450 390
TIG93 350 530 480
A
[mm]
B
[mm]
C
[mm]
TIG153 410 510 530
Tiger 2 - 9 kW Tiger 15 kW
SE: Väggfäste för förvaring av Tiger 2-15 kW
NO: Veggkonsoll for lagring av Tiger 2-15 kW
FR : Console murale pour rangement du Tiger 2-15 kW
DE: Wandhalterung für Tiger 2-15 kW (bei
Nichtgebrauch)
NL: Muurbeugel voor opslag van Tiger 2-15 kW
FI: Seinäkannake Tiger 2-15 kW:n säilytykseen
RU: Настенная скоба для подвески моделей
Tiger 2-15кВт при хранении
PL: Uchwyt ścienny do zawieszenia nagrzewnic
Tiger 2-15 kW
ES: Soporte mural para el almacenamiento de
Tiger 2-15 kW
DK: Vægbeslag til ophængning af Tiger 2-15 kW
HxWxD
[mm]
220400 LT22406 45x128x40
Wall bracket for storage of Tiger 2-15 kW
C
1
0
2
Tiger 2-15 kW
Fig. 1
SE: Återställning överhettningsskydd
NO: Tilbakestille overopphetingsvernet
FR: Réinitialisation de la protection anti-surchauffe
DE: Zurücksetzen des Überhitzungsschutzes
NL: Resetten van de oververhittingsbeveiliging
FI: Ylikuumenemissuojan palauttaminen
RU: Перезапуск защиты от перегрева
PL: Resetowanie zabezpieczenia przed przegrzaniem
ES: Reajustar la protección contra el
sobrecalentamiento
DK: Nulstilling af overophedningsbeskyttelsen
Resetting the overheat protection

Wiring diagrams
3
Tiger 2-15 kW
∼
∼
2
2
1
1
2a
2a
1a
1a
°C
°C
°C
°C
2
2
1
1
2kW
2kW
3kW
3kW
3kW
3kW
2 kW
2 kW
M
M
LN
Tiger 2 / 3 kW 230V~
230V~
21
∼
°C
M
2
1
LL L
123
Tiger 15 kW 230V3~/400V3~
400V 3~ / 230V 3~
12
400V 3~
230V 3~
400V 3~
°C
Tiger 5 kW 230V~
Item
number
Type Cable IEC60309
271734 TIG21 4G1,5x1,8m CEE7
271737 TIG31 3G1,5x1,8m CEE7
Item
number
Type Cable IEC60309
271752 TIG153-0 400V3~ 4G4x1,8m CP 432-6
271753 TIG15323 230V3~ 4G10x1,8m -
Item
number
Type Cable IEC60309
271742 TIG51 3G2,5x1,8m -

Wiring diagrams
4
Tiger 2-15 kW
°C
321
LLL
321
LLL
N
2
1
2a1a
°C
M
∼
2
1
400V 3~400V 3N~
2
2a
Tiger 3 / 5 / 9 kW 230V3~/400V3(N)~
230V 3~
Item
number
Type Cable IEC60309 230V-outlet
socket at
the rear
271739 TIG33-0 400V3~
4G1,5x1,8m CP 416-6 -
271745 TIG53-0 400V3~
271749 TIG93-0 400V3~
271740 TIG3323 230V3~ 4G1,5x1,8m CP 316-9 -
271747 TIG5323 230V3~
271751 TIG9323 230V3~ 4G2,5x1,8m CP 332-9 -
271738 TIG33 400V3N~
5G1,5x1,8m CP 416-6 Type F
271743 TIG53 400V3N~
271748 TIG93 400V3N~
271741 TIG33B 400V3N~
5G1,5x1,8m CP 416-6 Type E271746 TIG53B 400V3N~
271750 TIG93B 400V3N~
EN: 230V-outlet socket at the rear
SE: 230V-uttag på baksidan
NO: 230V uttak på baksiden
FR: Sortie de 230V à l’arrière
DE: 230V Steckdose
FI: 230V pistoke takana
NL: 230V-uitgang aan de achterkant
RU: Розетка 230В~ сзади
PL: Z tyłu gniazdo 230 V
ES: Toma de 230 V en la parte trasera
DK: 230V udtag på bagsiden

5
Tiger 2-15 kW
Item no Type Output
steps
[kW]
Airow
[m³/h]
Sound
power*1
[dB(A)]
Sound
pressure*2
[dB(A)]
∆t*3
[°C]
Motor
[W]
Voltage
[V]
Amp.
[A]
Weight
[kg]
271734 TIG21*50/2 240 47 33 25 17 230V~ 8,1 5,7
271737 TIG31 0/2/3 280 57 42 32 28 230V~ 13 6,0
271738 TIG33 0/1,5/3 280 57 42 32 28 400V3N~*44,4 6,3
271740 TIG3323 0/1,5/3 280 57 42 32 28 230V3~ 7,6 6,3
271742 TIG51 0/3,4/5 480 56 42 32 30 230V~ 22 6,7
271743 TIG53 0/2,5/5 480 56 42 32 30 400V3N~*47,2 6,7
271747 TIG5323 0/2,5/5 480 56 42 32 30 230V3~ 14,5 6,7
271748 TIG93 0/4,5/9 720 65 51 38 48 400V3N~*413 10
271751 TIG9323 0/4,5/9 720 65 51 38 48 230V3~ 26 10
271752 TIG153-0 0/7,5/15 1120 66 52 41 65 400V3~ 22 16
271753 TIG15323 0/7,5/15 1120 66 52 41 65 230V3~ 37,5 16
*1) Sound power (LWA) measurements according to ISO 27327-2: 2014, Installation type E.
*2) Sound pressure (LpA). Conditions: Distance to the unit 3 metres. Directional factor: 2. Equivalent
absorption area: 200 m².
*3) ∆t = temperature rise of passing air at maximum heat output.
*4) Also available without neutral and are then called TIG33-0, TIG53-0 and TIG93-0. These models do not
have the 230V socket on the reverse and are equipped with P416-6 connectors.
*5) Also available as TIG21CH, supplied with plug for Switzerland.
Tiger 2-9: Approved for 220V/1ph/60Hz and 380V/3ph/60Hz. Product performance for 220V/1ph/60Hz and
380V/3ph/60Hz will differ from stated data.
Technical specications Tiger 2-15 (IP44)
EN: Output steps
SE: Effektsteg
NO: Effekttrinn
FR: Puissances
DE: Abgabestufen
FI: Tehoportaat
NL: Capaciteit
RU: Ур. мощности
PL: Stopnie mocy
ES: Niveles de potencia
DK: Effekttrin
EN:Airow
SE: Luftöde
NO:Luftstrøm
FR: Débit d’air
DE: Luftmenge
FI: Ilmavirta
NL: Luchtstroom
RU: Расх.возд.
PL: Wydajność powietrza
ES: Caudal de aire
DK: Luftmængde
EN: Soundpower
SE: Ljudeffekt
NO:Lydeffekt
FR: Puissance acoustique
DE: Schallleistung
FI: Ääniteho
NL: Geluidsvermogen
RU: Мощность звука
PL: Moc akustyczna
ES: Potencia acústica
DK: Lydeffekt
EN: Sound pressure
SE: Ljudtryck
NO:Lydtrykk
FR: Pression acoustique
DE: Schalldruck
FI: Äänenpaine
NL: Geluidsdruk
RU: Звуковое давление
PL: Ciśnienie akustyczne
ES: Presión acústica
DK: Lydtryk
EN: Motor
SE: Motor
NO:Motor
FR: Moteur
DE: Motor
FI: Moottori
NL: Motor
RU: двигатель
PL: Silnika
ES: Motor
DK: Motor
EN: Voltage
SE: Spänning
NO:Spenning
FR: Tension
DE: Spannung
FI: Jännite
NL: Voltage
RU: Напряжение
PL: Napięcie
ES: Tensión
DK: Spænding
EN: Amperage
SE: Ström
NO:Strøm
FR: Intensité
DE: Strom
FI: Virta
NL: Stroomsterkte
RU: Сила тока
PL: Natężenie
ES: Intensidad
DK: Strømstyrke
EN: Weight
SE: Vikt
NO:Vekt
FR: Poids
DE: Gewicht
FI: Paino
NL: Gewicht
RU: Вес
PL: Masa
ES: Peso
DK: Vægt

6
Tiger 2-15 kW
NO:
*1) Målinger av lydeffekt (LWA) i henhold til ISO 27327-2: 2014, Installasjon type E.
*2) Lydtrykk (LpA). Betingelser: Avstand til aggregat 3 meter. Retningsfaktor: 2. Ekvivalent absorpsjonsareal:
200 m².
*3) ∆t = temperaturøkning på gjennomstrømmende luft ved maksimal varmeeffekt
*4) Finnes også uten nulleder og har da typebetegnelse TIG33-0, TIG53-0 og TIG93-0. Disse modellene har
ikke 230 V uttak på baksiden og er utstyrt med P416-6-kontakter.
*5) Fås også som TIG21CH, utstyrt med sveitsisk støpseltype.
Tiger 2-9: Godkjent for 220 V/1-fase/60 Hz og 380 V/3-fase/60 Hz. Produktytelse for 220 V/1-fase/60 Hz og
380 V/3-fase/60 Hz avviker fra angitte data.
FR:
*1) Mesures de la puissance acoustique (LWA) selon la norme ISO 27327-2 : 2014, Installation de type E.
*2) Pression acoustique (LpA). Conditions : Distance de l’appareil : 3 mètres. Facteur directionnel : 2. Surface
d’absorption : 200 m².
*3) ∆t = augmentation de température sous une puissance maximale.
*4) Egalement disponible sans neutre. Leurs références sont alors TIG33-0, TIG53-0 et TIG93-0. Ces modèles
ne disposent pas de la prise 230 V à l’arrière mais sont équipés des connecteurs P416-6.
*5) Également disponible sous la référence TIG21CH, doté d’un cordon avec che pour la Suisse.
Tiger 2-9 : Compatible avec une alimentation 220 V/monophasée/60 Hz ou 380 V/triphasée/60 Hz. Les
performances du produit avec une alimentation 220 V/monophasée/60 Hz ou 380 V/triphasée/60 Hz peuvent
différer des données indiquées.
DE:
*1) Schallleistungsmessungen (LWA) gemäß ISO 27327-2: 2014, Installationstyp E.
*2) Schalldruck (LpA). Bedingungen: Abstand zum Gerät: 3 Meter. Richtungsfaktor: 2. Entsprechende
Absorptionsäche: 200 m². .
*3) ∆t = Temperaturanstieg bei maximaler Heizleistung.
*4) Auch ohne Nullleiter erhältlich und heißen dann TIG33-0, TIG53-0 und TIG93-0. Diese Modelle haben
keinen 230-V-Anschluss auf der Rückseite und sind mit P416-6-Steckern versehen.
*5) Auch erhältlich als TIG21CH mit Stecker für die Schweiz.
Tiger 2-9: Zugelassen für 220V/1ph/60Hz und 380 V/3ph/60 Hz. Die Produktleistung für 220V/1ph/60Hz und
380 V/3ph/60 Hz weicht von diesen angegebenen Daten ab.
FI:
*1) Äänitehon (LWA) testausmenetelmät standardin ISO 27327-2: 2014 mukaan, asennustyyppi E.
*2) Äänenpaine (LpA). Mittausjärjestelyt: Etäisyys laitteeseen 3 m. Suuntaavuuskerroin 2. Ekvivalentti
absorptioala: 200 m².
*3) ∆t = läpivirtaavan ilman lämpötilan nousu suurimmalla lämpöteholla.
*4) Saatavana myös ilman nollajohdinta, jolloin tyyppi on TIG33-0, TIG53-0 ja TIG93-0. Näissä malleissa ei ole
230 V~ pistorasiaa takapuolella.
*5) Saatavana myös TIG21CH-versio, jossa on Sveitsin markkinoille tarkoitettu pistotulppa.
Tiger 2-9: Hyväksytty myös 220 V/1-v/60 Hz ja 380 V/3-v/60 Hz syöttöjännitteille. Kojeiden suoritusarvot
220 V/1-v/60 Hz ja 380 V/3-v/60 Hz syöttöjännitteillä poikkeavat yllä ilmoitetuista tiedoista.
SE:
*1) Ljudeffekt (LWA), mätningar enligt ISO 27327-2: 2014, Installationstyp E.
*2) Ljudtryck (LpA). Förutsättningar: Avstånd till aggregat 3 meter. Riktningsfaktor: 2. Ekvivalent
absorptionsarea 200 m².
*3) ∆t = temperaturhöjning på genomgående luft vid maximal värmeeffekt.
*4) Finns även utan nolla och har då typbeteckningarna TIG33-0, TIG53-0 och TIG93-0. Dessa modeller saknar
230V-uttag på baksidan och är försedda med anslutningsdon P416-6..
*5) Finns även som modell TIG21CH, försedd med en kabel med ett schweiziskt don.
Tiger 2-9: Godkänd för 220V/1ph/60Hz och 380V/3ph/60Hz. Produktprestanda för 220V/1ph/60Hz och
380V/3ph/60Hz skiljer sig från redovisade värden.

7
Tiger 2-15 kW
NL:
*1) Metingen van het geluidsvermogen (LWA) volgens ISO 27327-2: 2014, installatietype E.
*2) Geluidsdruk (LpA). Condities: Afstand tot de unit 3 meter. Richtingsfactor: 2. Equivalent absorptiegebied:
200 m².
*3) ∆t = Temperatuurstijging van de passerende lucht op maximale verwarming.
*4) Ook verkrijgbaar zonder nul en wordt dan TIG33-0, TIG53-0 en TIG93-0 genoemd. Deze modellen
beschikken niet over een 230V-stopcontact aan de achterkant, maar zijn voorzien van P416-6 connectoren.
*5) Ook verkrijgbaar als TIG21CH, geleverd met snoer met stekker voor Zwitserland.
Tiger 2-9: Goedgekeurd voor 220V/1-fase/60Hz en 380V/3-fase/60Hz. Productprestaties voor 220V/1-
fase/60Hz en 380V/3-fase/60Hz wijken af van de gespeciceerde data.
RU:
*1) Мощность звука (LWA) измерена в соответствии с ISO 27327-2: 2014, Тип установки E.
*2) Звуковое давление (LpA). Условия: Расстояние до прибора 3 метра. Фактор направленности 2.
Эквивалентная площадь звукопоглощения 200 м2.
*3) ∆t = подогрев потока при максимальной мощности.
*4) возможно исполнение без нейтрали и тогда модели маркируются соответственно TIG33-0,
TIG53-0 и TIG93-0. У этих моделей на задней стороне нет розетки 230В, имеют шнур с 5-и полюсной
вилкой P416-6 европейского образца.
*5) Можно заказать модель TIG21CH с кабелем и вилкой по стандарту для Швейцарии.
Tiger 2-9: Одобрены для работы при 220В/1ф/60Гц и 380В/3ф/60Гц. Технические характеристики будут
отличаться от указанных в таблице.
PL:
*1) Pomiary mocy akustycznej (LWA) zgodnie z normą ISO 27327-2: 2014, Instalacja typu E.
*2) Ciśnienie akustyczne (LpA). Warunki: Odległość do urządzenia 3 m. Współczynnik kierunkowy: 2.
Powierzchnia absorpcji: 200 m².
*3) ∆t = przyrost temperatury przy maksymalnej mocy grzewczej.
*4) Występują także w wersjach bez przewodu zerowego, oznaczonych TIG33-0, TIG53-0 i TIG93-0. Te modele
nie mają z tyłu gniazda 230 V i są wyposażone w złącza P416-6.
*5) W Szwajcarii występuje także jako model TIG21CH dostarczany z kablem z wtyczką.
Tiger 2-9: Produkt zatwierdzony dla zasilania 220 V/1 faza/60 Hz i 380 V/3 fazy/60 Hz. Wydajność produktu
dla zasilania 220 V/1 faza/60 Hz i 380 V/3 fazy/60 Hz będzie się różnić od podanych danych.
ES:
*1) Mediciones de potencia acústica (LWA) de conformidad con ISO 27327-2: 2014, Instalación de tipo E.
*2) Presión acústica (LpA). Condiciones: 3 metros de distancia a la unidad. Factor direccional: 2. Área de
absorción equivalente: 200 m².
*3) ∆t = incremento de la temperatura derivado del paso del aire a la potencia caloríca máxima..
*4) También disponible sin neutro y entonces se llaman TIG33-0, TIG53-0 y TIG93-0. Estos modelos no tienen
la toma de corriente de 230 V en la parte trasera sino que están equipados con los conectores del tipo
P416-6.
*5) También está disponible la versión TIG21CH, suministrada con un cable con enchufe para Suiza.
Tiger 2-9: Puede utilizarse a 220V/1ph/60Hz y 380V/3ph/60Hz. Los datos técnicos para 220V/1ph/60Hz y
380V/3ph/60Hz son diferentes a los aquí indicados.
DK:
*1) Lydeffektmålinger (LWA) i henhold til ISO 27327-2: 2014, Installationstype E.
*2) Lydtryk (LpA). Forhold: Afstand til enheden; 3 meter. Retningsfaktor: 2. Tilsvarende absorberingsområde:
200 m².
*3) ∆t = temperaturstigning i passerende luft ved maksimal varmeeffekt.
*4) Også tilgængelig uden nul, og betegnes da TIG33-0, TIG53-0 og TIG93-0. Disse modeller har ikke
230 V-udtag på bagsiden og er udstyret med P416-6-stik.
*5) Også tilgængelig som TIG21CH, som leveres med ledning og stik til Schweiz.
Tiger 2-9: Godkendt til 220 V/1-faset/60 Hz og 380 V/3-faset/60 Hz. Produktets ydeevne for 220 V/1-faset/60
Hz og 380 V/3-faset/60 Hz vil afvige fra de anførte data.

°C
0
1
°C
0
1
8
Tiger 2-15 kW
EN
Installation and operating instructions
Output is set via the output selector,
for steps see Technical specications.
Built-in thermostat with setting
range 5–35°C.
Control
The unit is equipped with mechanic thermostat
room temperature control and can be used as
a local space heater according to Ecodesign
Regulation (EU) 2015/1188.
Tiger 15 kW
Mode selector:
0: Control of heat only (fan blows
continuously)
1: Control of fan speed and heat
Tiger 2–9 kW
Output is set via the output selector, for
steps see Technical specications.
Built-in thermostat with setting range
5–35°C.
The built-in thermostat controls fan speed and
heat, or heat only. The choice is made with the
mode selector. When operating with heat only
the fan blows constantly and the thermostat
only controls the heat output.
Output
steps TIG33 400V3N~ TIG53 400V3N~ TIG93~ 400V3N~
1/2 16 A 16 A 16 A
1/1 11.7 A 8.8 A 3 A
Start-up
When the unit is used for the rst time or after
a long period of non-use, smoke or an odour
may result from dust or dirt which has collected
on the element. This is completely normal and
disappears after a short time.
Max load for the outlet socket at the rear,
depending on the selected output
General Instructions
Read these instructions carefully prior to
installation and use. Keep this manual for
future reference.
The product may only be used as set out in
the assembly and operating instructions. The
guarantee is only valid should the product be used
in the manner intended and in accordance with
the instructions.
Application
Tiger is a range of robust and compact fan
heaters for professionals with high demands.
The Tiger fan heater is portable. Tiger 2-9 kW
are intended for heating and drying areas such
as garages, workshops and shops. Tiger 15 kW
is ideal for heating and drying larger premises
such as industrial premises and workshops,
where higher outputs are required.
Protection class: IP44.
Connection
The Tiger fan heater is equipped with a
1.8 metre long connection cable.
• TIG21 and TIG31 have cords with plugs for
connection to earthed outlet sockets. TIG21
requires 10 A fuse protection, TIG31 requires
16 A fuse protection.
• TIG51 has a cable without plug.
• TIG33, TIG53, TIG93 and TIG153-0 have an
IEC60309 plug tted on the connection cable.
There is a 230V-outlet socket of type F at the
rear of TIG33, TIG53 and TIG93. The socket
gives the possibility to connect, for example,
lighting or a charger for cordless tools.
Products with 230V-outlet socket of type E are
also available for ordering.
See the introduction pages.
The fan heater must be protected by a 16 A-fuse.

9
Tiger 2-15 kW EN
Maintenance
The motor and other components are
maintenance-free. Dust and dirt may cause
overheating and danger of re. The appliance
must therefore be cleaned regularly.
Residual current circuit breaker
When the installation is protected by means of
a residual current circuit breaker, which trips
when the appliance is connected, this may be
due to moisture in the heating element. When
an appliance containing a heater element has
not been used for a long period or stored in
a damp environment, moisture can enter the
element.
This should not be seen as a fault, but is
simply rectied by connecting the appliance to
the main supply via a socket without a safety
cut-out so that the moisture can be eliminated
from the element. The drying time can vary
from a few hours to a few days. As a preventive
measure, the unit should occasionally be run
for a short time when it is not being used for
extended periods of time.
Packaging
Packaging materials are chosen with
consideration to the environment and are
therefore recyclable.
Handlingofproductatendofworking
life
This product may contain substances necessary
for the functionality of the product but
potentially dangerous for the environment. The
product should not be disposed of mixed with
general household waste but delivered to a
designated collection point for environmental
recycling. Please contact the local authority
for further details of your nearest designated
collection point.
Safety
• For all installations of electrically heated
products a residual current circuit breaker
300 mA for re protection should be used.
• Keep the areas around the air intake and
exhaust grilles free from possible obstructions!
• The unit must not be fully or partially covered as
overheating can result in a re risk!
• The unit must not be placed directly under xed
wall sockets!
• This appliance can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved. Children
shall not play with the appliance. Cleaning and
user maintenance shall not be made by children
without supervision.
• Children of less than 3 years should be kept
away unless continuously supervised.
• Children aged from 3 years and less than 8
years shall only switch on/off the appliance
provided that it has been placed or installed
in its intended normal operating position and
they have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved.
• Children aged from 3 years and less than 8
years shall not plug in, regulate and clean the
appliance or perform user maintenance.
CAUTION — Some parts of this product can
become very hot and cause burns. Particular
attentionhastobegivenwherechildrenand
vulnerable people are present.
Overheating
The fan heater is equipped with an overheat
protection. If it is deployed due to overheating,
reset as follows:
1. Disconnect the power supply.
2. Determine the cause of overheating and
rectify the fault.
3. Reset by pushing the red button on top of the
unit. Fig. 1
NOTE! All work inside the unit’s connection
area must be carried out by a qualied
technician and with the power supply
disconnected.

Mainoffice
Frico AB Tel: [phone]
Industrivägen 41
SE-433 61 Sävedalen [email protected]
Sweden www.frico.net
For latest updated information and information
   aboutyourlocalcontact:www.frico.net
Art.nr: 278365 2022-03-15 CH