fully Jarvis User manual

Jarvis L-shaped standing desk
Assembly instructions
For assembly assistance,
visit fully.com/instructions,
contact us at 888-508-3725
or [e-mail]

Thank you for choosing a Jarvis desk from Fully.

3
Cautions and use
Contact
Before starting
Specs
In the box
Assembly
Initial calibration & reset
Custom settings
Using your own desktop
4
4
5
5
6
8
21
22
23

4
Please read this manual carefully. If this desk changes hands,
please provide this manual to the new owner.
Make sure the desktop is not touching any obstacles or walls
and that no obstacles are in the desk’s path. Make sure all
cords are an appropriate length to accommodate the full
range of height adjustment.
Keep children away from the desk components. There is risk
of injury and electric shock.
Do not sit or stand on the the desk frame. Do not crawl or lie
under the desk frame.
Do not open or modify any of the components, including
the Lifting Columns, Control Box, or Handset. Doing so risks
electric shock and voids any warranty claims.
Placing objects taller than 20” underneath the desk will
obstruct the desk’s movement and may result in physical
damage.
Cautions
Voltage converters
Using a voltage converter could cause damage to the desk,
and is considered improper use. Resulting damage is not
covered by the warranty.
Verify the voltage of the Control Box as labeled to avoid
damage. Alternative voltage Control Boxes are available
from Fully.
Use & liability
This Jarvis height adjustable desk has electric motors and
is designed for use in dry work environments only.
This Jarvis desk is adjustable so it can be positioned at an
optimal ergonomic height. Any extracurricular use is at
user’s own risk.
Under no circumstances does the manufacturer accept
warranty claims or liabilityclaims for damage caused by
improper use or handling of the desk frame.
Jarvis is a registered trademark of Fully, LLC.
All rights reserved.
North America
Portland, Oregon
888-508-3725
[e-mail]
fully.com
Europe
Ghent, Belgium
[e-mail]
fully.eu/contact
fully.eu
Contact

5
On a padded or carpeted area, take all of the items out of
your Jarvis frame box and confirm that nothing is missing.
Reference the included parts listings on page 6.
Before starting
If you are using your own desktop, refer to page 16 for
instructions before beginning assembly.
Using your own desktop
Tools
3mm
Hex Wrench
4mm
Hex Wrench
Phillips Screwdriver
(not included)
5mm
Hex Wrench

6
Parts
*Not to scale
Side Leg x2
C
PCorner LegCenter Rail x4 O
Foot x2
D
Control Box
FLeg Cable x2 GPower Cable HE Memory Handset
Center Rail Support
M
Noise Attenuation
Pad x10
AB
Desktop Washer x16
Y
Crossbar x2
R
Mending Plate x2
QCable Clip x15 S
Frame End Frame End with Capture
Plate
Corner Frame End-A Corner Frame End-B
I J K L
Corner Bracket
N
Left Side Bracket
B
Right Side Bracket
A
Wood Screw x24
T
ULarge Machine Screw x4 Medium Machine Screw x12 Small Machine Screw x14 Thick Machine Screw x8 V W X
Noise Attenuation
Grommet x10 (Extra)
AC
Box 1
Box 2
AA Desktop Screw x16
for all other work surfaces
ZDesktop Screw x16
for bamboo work surfaces

7
*Not to scale
Large Desktop Small Desktop
AD AE Desktop Screw x16
(Extra)
AF
Desktop boxes(2)

8
1
Lay the two pieces of your desktop down on a padded surface (tops down) as shown in the image that matches
how you want your desk positioned.
Next, decide whether you want the Memory Handset on your right or left. (The Handset placed on your left during
assembly will be on the right once the desk is flipped over, and vice versa.)
The following instructions show the assembly of a desk as shown in configuration 2 below: the smaller desktop will
be on the left, and the Handset will be on the right (mounted to the larger desktop). We’ll point out the steps where
you’ll need to make adjustments for other orientations.
=
1 1
=
3 3
=
4 4
=
2 2

9
J
W
C
Jx4
W
C
x1
3
2
W
I
C
x4
W
C
x1
I
4 mm
4 mm

10
4
A
V
2
Ax2
V
24 mm
B
V
3
Bx2
V
3
5
4 mm