fully Jarvis User manual

Jarvis crank-powered standing desk
Assembly instructions
For assembly assistance,
visit fully.com/howtojarvis
or call 888-508-3725
or email [e-mail]

Thank you for choosing a Jarvis desk from Fully.
1

Cautions & Use
Make sure the desk top is not in contact with any
obstacles or walls.
Make sure the desk top is not touching any walls. Make
sure all cords are an appropriate length to accommo-
date the full range of height adjustment.
Do not sit or stand on the desk frame. Do not crawl or
lie under the desk frame.
Do not place any objects taller than 25” underneath the
desk.
Be careful to not pinch your hand when using the handle.
The desk height is adjustable so that it can be
positioned at the most ergonomically suitable height.
Any other operation is at user’s own risk.
Under no circumstances does the manufacturer
accept warranty claims or liability claims for damages
caused from improper use or handling of the desk
frame.
Please read this manual carefully. If this desk is resold,
please provide this manual to the new owner.
2

In the box
3
left lifting column
1L
right lifting column
1R
feet x2
2
left side bracket
3L
right side bracket
3R
frame ends x2
4
center rails x2
5
hand crank
6
crank sleeve
8
driving rod sleeves x2
9
adapter plate
11
crank spring
12
wood screw x12
M5x16
14
large machine screw x16
M6x14
15
medium machine screw x12
M6x10
16
small machine screw x2
M5x10
17
driving rod
10
crank washer x2
13
right side crank rod
7R
left side crank rod
7L

4
Tools
On a padded or carpeted
area, take all of the items
out of your Jarvis frame box,
and confirm that nothing is
missing.
Before Starting
Pro Tip
Wood Screws:
Pointy End
Machine Screws:
Flat End
6mm wrench
included
3mm hex key
included
5mm hex key
included
#2 Philips Screwdriver
provide your own

step 1
Insert the left lifting column (Part 1L - Labeled “L”) into the frame end (Part 4) as shown below.
To secure the frame end to the leg, thread four (4) of the large machine screws (Part 15) into
the holes as shown, but do not tighten them all the way.
Once all four screws are in place, tighten completely.
step 2
Select the left side bracket (Part 3L - Labeled “L”). The two tabs on the side bracket will slot
into the frame end (Part 4), around the lifting column (Part 1L).
Use two of the medium machine screws (Part 16) to secure the side bracket. As before, don’t
tighten all the way until both screws are in place.
5
step 3
Repeat Steps 1–2 for the right leg, frame end, and side bracket.
Assembly
1L
4
3L
1L
4

6
step 4
Lay your desk top on your
padded workspace with the
underside facing up, and the
front of the desk top towards
you.
Place the right leg assembly
(with “R” labels) on the desk
top to your left, with the frame
end pointing towards you.
(Once you flip your desk over,
this will become the right side,
and the world will make sense
again.)
If the pre-drilled holes have
metal inserts, you will need to
use the machine screws pack-
aged with the Jarvis desk top
to secure the frame; otherwise
use five (5) wood screws
(Part 14) to attach the leg
assembly to the desk top.
Insert all five screws part way.
Once they are in place, tighten
them all completely.
step 5
Slide the center rails (Part 5) all the way into the frame end
attached to the desk top, so that the midpoint mark is facing
up, and the cut-out slots are facing inwards.
Slide the left leg assembly (with “L” labels) onto the other end
of the center rails (your right-hand side), and the entire frame
should now fit onto the desk top.
correct center rail orientation
3R
1R
Pro Tip
Wood Screws: Pointy End
Machine Screws: Flat End
5
3L
1L
front edge of Jarvis desk top
4
3R
1R

step 6
Secure the left leg assembly
with the remaining screws.
Again, if the pre-drilled holes
have metal inserts, you will
need to use the machine
screws packaged with the desk
top to secure the frame; other-
wise use five (5) wood screws
(Part 14).
Insert all five screws part way.
Once they are in place, tighten
them all completely.
step 7
Center the labeled midpoints
on both center rails (Part 5)
between the two frame ends
(Part 4), and use eight (8) of
the medium machine screws
(Part 16) to lock the center rails
down firmly.
Warning: Skipping this step
may result in stability issues.
7

setscrew too tight
setscrew just right
8
step 8
Assemble the driveshaft by
sliding the two driving rod
sleeves (Part 9) over each end
of the driving rod (Part 10).
The sleeves have setscrews
pre-inserted on both ends.
Do not tighten setscrews until
step 9. Make sure these set-
screws are lined up with each
other and are loose enough (as
shown) to allow the driving rod
to slide into the sleeve com-
pletely.
If the rod will not go past a
setscrew, loosen the setscrew
a little with the 3mm hex key.
step 9
Place the assembled driveshaft
between the two rod ends ex-
tending from the lifting columns.
Slide the sleeves onto these
rod ends completely, and make
sure all setscrews are facing up
and lined up with each other as
shown.
If the driveshaft does not easily
line up with both rod ends you
can use the included wrench to
rotate one of the rod ends into
alignment.
Once the driveshaft is installed
on both sides, tighten all four
setscrews to lock them in place.
Note: Do not over tighten the
setscrews. Stop once they make
contact with the rods and no
longer turn easily.
10
9 9
10
9

9
Right side hand crank: Insert
the long crank rod (160mm -
Part 7R) into the crank socket
on the right lifting column
(marked “R”) and be sure the
raised notches go inside the
leg.
Left side hand crank: Insert the
short crank rod (125mm - Part
7L) into the crank socket on
the left lifting column (marked
“L”) and be sure the raised
notches go inside the leg.
step 10
Decide whether you want the hand crank to be on the left side or right side of the desk.
step 12
Orient the crank sleeve (Part 8) so that its setscrew is closest to the leg and pointing up, and
slide it onto the crank rod.
Slide the crank (Part 6) all the way into the crank sleeve, making sure that the pin on the hand-
crank rod lines up with the notch in the crank sleeve as shown, and fit the plastic arch-shaped
crank bushing onto the crank sleeve.
Note: the hand crank cannot be attached directly to the desk top!
step 11
Slide a crank spring washer
(Part 13), then the crank spring
itself (Part 12), then the second
washer onto the crank rod, as
shown.
Using the two (2) wood screws (Part 14), attach the adapter plate (Part 11) making sure that
the “R” or “L” label matches your chosen orientation. If you have a Jarvis desk top, use the
widely-spaced pre-drilled holes for this purpose.
right-hand crank setup left-hand crank setup
3R 3L
7R
7L
11 11
crank bushing
12
13
13
7R
8
6
8

step 13
Attach the plastic crank bushing to the adapter plate (Part 11) using the two (2) small machine
screws (Part 17). Tighten the set screw on the crank sleeve.
10
step 14
Loosely attach the feet (Part 2) to the bottom of the lifting columns with four (4) large machine
screws (Part 15) per foot. Once all the screws are in place, tighten them down the rest of the way
in an X pattern.
step 15
Double check that all screws everywhere on the desk are tight.
step 16
With a friend, lift the desk, and carefully flip it onto its feet being careful not to put weight on
the hand crank. Then adjust the pre-installed leveling glides on the feet (Part 2) as needed.
Collapsable Handle
Slide and rotate the hand
crank under the desk for
convenient crank storage
Caution: Pinching hazard. Please be careful not
to pinch your hand when flipping the handle.
2 2
11
17

Desks, chairs & things
to keep you moving
90.014.01.0499v.d