Galvin Engineering 656512 Instruction sheet

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 1, 6th July 2022, Page 1of 5
SS Vandal Resistant D/F Plate Assembly
for Pneumatic Inwall Cistern w/ CP BS
Raised Buttons
PRODUCT CODES
- 656512
SPECIFICATIONS
−Face plate assembly features pneumatic dual flush push activation buttons for CIST19-PNEU-2 Slim-
Line Inwall Cistern.
−2mm thick, Vandal resistant stainless steel faceplate.
TECHNICAL DATA
Activation
Push Button
Connections
Pneumatic
Hose Length
3 metres
Finish
Polished
NOTE: Galvin Engineering continually strive to improve their products. Specifications may change without
notice.
MOUNTING DETAILS
If a cut out is required, refer to the face plate position and cut out details below.
- The push button can be positioned as preferred but consideration should be given to ensure it is easily
accessible for children and adults.
- A 70mm x 140mm x 80mm cut out is required in the wall to fit the two push buttons. Drill two holes 160
mm from centres as shown for two nylon wall plugs 8 X 40 (NWP8).

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 1, 6th July 2022, Page 2of 5
DIMENSIONS

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 1, 6th July 2022, Page 3of 5
INSTALLATION
INSTALLATION COMPLIANCE: Galvin Engineering products must be installed in accordance with these
installation instructions and in accordance with your local regulatory requirements. Water and/or electrical supply
conditions must also comply to the applicable national and/or state standards. Failing to comply with these
provisions shall void the product warranty and may affect the performance of the product.
Assemble the push buttons and faceplate.
- Insert the pneumatic push buttons into the
faceplate and fasten together using hex nuts.
- Ensure the rubber washers are placed in
between the faceplate and the hex nuts.
Connect the pneumatic tubes to the push
buttons.
- Connect one end of the air tube to the push
button and the other end to the cistern.
- Ensure the tube is connected to the correct
button (half or full flush).
- Check if the connections are tight and secure.
- Check if both buttons are operational and
check the air tubes for leaks
1.
2.

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 1, 6th July 2022, Page 4of 5
Mount the faceplate.
- Install nylon wall plugs as shown.
- Apply a thin bead of silicon on the edge of cut out
- Mount the faceplate to the wall using the two
countersunk torx screws.
- Ensure the screws are securely tightened and
the faceplate is mounted flush to the wall.
Check for correct operation.
3.
4.

Product Installation Guidelines
Version 1, 6th July 2022, Page 5of 5
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty
Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied.
Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including
but not limited to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download
from www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free
from operational defects in workmanship and materials for the warranty period as shown on the schedule in
the manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any
defective products manufactured by Galvin Engineering without charge, so long as the terms of the
Manufacturer’s warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy
for breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product.
TROUBLESHOOTING
PROBLEM
CAUSE
RECTIFICATION
Cistern does not flush
No air supplied from air pump
Check air tube for leaks
Replace air pump if damaged
Faulty Push Button
Replace damaged push button
Incorrect connections
Check all connections
NON-SERVICEABLE PRODUCTS INFORMATION
Push Button, Air Pump, Face Plate
These items are non-serviceable products. If damaged, they must be replaced.
If there appears to be any problems with these items, please contact Galvin Engineering.
Note: Before attempting to replace any of these items check that you have access to re-run the
connection leads. If you do not have access or you have any doubts, please contact Galvin Engineering
for advice before commencing replacement.