Galvin Engineering Ezy-Drink 85326X Instruction sheet

Version 3, 31 May 2019, Page 1of 4
Ezy-Drink®Lead Free Remote Bottle Filler
PRODUCT CODES:
-85326X
SPECIFICATIONS
−Lead Free stainless steel construction
IMPORTANT: All Ezy-Drink®remote Bottle Fillers are tested in accordance with AS/NZS 3718 and leave our
premises in good working order.
Inlet
1/2” BSP - Female
Outlet
Stainless Steel Gooseneck
Headwork
N/A
Working Pressure Range (kPa)
Min
30
Max
1000
Working Temperature Range (°C)
Min
2
Max
65
Nominal Flow Rate (LPM)
N/A
TOOLS REQUIRED
−Power drill
−Wrench
−2mm Hex Key (provided)
−Screwdriver
PRE-INSTALLATION - MOUNTING DETAILS
−If the mounting holes do not already exist, mark out and drill the holes in the bench/trough, as shown in the
rough-in dimensions.
Note: Before installation, all lines must be flushed. We recommend that a line strainer be installed prior to drinking
taps to eliminate any foreign material.
37
268
228
LOCKING
SCREW
SEALING
O RING
34
90
G 1/2"
Rough-In Dimensions

Version 3, 31 May 2019, Page 2of 4
INSTALLATION
IMPORTANT: Galvin Engineering products must be installed in accordance with these installation instructions
and in accordance with AS/NZS 3500, the PCA and your local regulatory requirements. Water and/or electrical
supply conditions must also comply to the applicable national and/or state standards. Failing to comply with
these provisions shall void the product warranty and may affect the performance of the product.
1. Fit Stem
−Drill hole in bench/trough as shown in
rough-in dimensions.
−Fit O-Ring to the groove underneath the
stem.
−Fit stem through the drilled hole
ensuring the O-Ring has seated
properly.
2. Fit Locking Nut
−Fit and Tighten locking nut until it stops (roughly 8mm
below the bench/trough).
3. Fit thumb screws
−Fit thumb screws into the threaded holes on the locking nut and tighten until the stem is securely
mounted on the bench/trough.

Version 3, 31 May 2019, Page 3of 4
4. Fit Bottle Filler
−Fit bottle filler into stem ensuring it is seated correctly.
−Turn the bottle filler to the desired position.
−Once positioned, fit and tighten grub screw. The bottle filler should no longer turn.
5. Test
−Test installation and check for leaks.

Version 231 May 2019, Page 4of 4
TROUBLESHOOTING
PROBLEM
CAUSE
RECTIFICATION
Inconsistent flow
Blocked top assembly
Remove top assembly and clean
Water is not flowing from
bottle filler
Water is turned off
Turn on water
Installation is leaking
Incorrectly installed
Disassemble and follow the installation
instructions above ensuring the O-
Rings are positioned correctly.
Installation loose
Locking screws underneath
haven’t been adequately
tightened.
Follow step 3 of the installation guide
and ensure the screws are tight enough
to avoid movement of the installation.
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty
Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied.
Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including
but not limited to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download
from www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free
from operational defects in workmanship and materials for the warranty period as shown on the schedule in
the manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any
defective products manufactured by Galvin Engineering without charge, so long as the terms of the
Manufacturer’s warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy
for breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product.