Galvin Engineering Safe-Cell 50150 Instruction sheet

Version 1, 30 August 2018, 1 of 4
Safe-Cell® Prison Basin Set
PRODUCT CODE:
- 50150
SPECIFICATIONS
 The Safe-Cell® Timeflow Push Button Valve is used in prisons, detention centres, high risk institutions,
sporting facilities, schools and public area applications
 Once activated, this timed flow product will allow water to flow for approximately 15 seconds*
 Designed for easy bench installation (maximum thickness 10mm)
 Time is based on set at 500kPa, 4LPM @ 22˚C. Time is affected by temperature, flow rate and pressure
 Chrome plate finish
Note: This is a single temperature product, so if warm water is required this needs to be premixed prior to
reaching the valve. This can be done by using a CliniMix® Thermostatic Mixing Valve.
IMPORTANT: All Safe-Cell® prison taps are tested in accordance with AS/NZS 3718 and leave our
premises in good working order.
TECHNICAL DATA
Inlet ½” BSP – Male
Outlet Dome Outlet
Headwork Time flow cartridge
Working Pressure Range (kPa) Min 100
Max 500
Maximum Working Temperature (°C) Min 5
Max 70
Nominal Flow Rate (LPM) 2.55
Construction Brass
Finish Chrome
NOTE: Galvin Engineering continually strive to improve their products. Specifications may change without
notice.
TOOLS REQUIRED
 Power drill
 Spanner or adjustable crescent

Version 2, 30 August 2018, 2 of 4
PRE-INSTALLATION
MOUNTING DETAILS
 If the mounting holes do not already exist, mark out and drill the holes in the bench/trough, as shown
in rough-in dimensions.
Note: Supplied flexi hose length is 450mm long. Maximum distance between outlet and push button
adjustment is 420mm.
INSTALLATION
INSTALLATION COMPLIANCE: Galvin Engineering products must be installed in accordance with these
installation instructions and in accordance with AS/NZS 3500, the PCA and your local regulatory
requirements. Water and/or electrical supply conditions must also comply to the applicable national and/or
state standards. Failing to comply with these provisions shall void the product warranty and may affect the
performance of the product.
IMPORTANT: Whilst our product designs take into account a broad range of installation types and surfaces,
it is important that surfaces which fixtures are mounted to are flat and free from defect. This is especially
important when installing product ranges that have been designed for correctional and health facilities, where
special attention is required to minimise ligature points and areas for concealment of contraband. In addition
to ensuring the products are fitted securely and in accordance with the following instructions, consideration
shall be given to the use of non-pick mastics such as BASF Sonolastic “Ultra” to ensure a high quality and
safe installation.
22
4
15.0
15.0
22
4
420 MAX
BENCH / TROUGH
FLOW DIRECTION
22
70
PUSH BUTTON ASSEMBLY
WATER HOSE 15F R/CONE
1/2"BSP
HEX W/ELBOW x 450mm LONG
1/2"BSP
1/2"BSP
ISOLATING/
REGULATING
BALL VALVE
BASIN OUTLET 175
22

Version 2, 30 August 2018, 3 of 4
1. Fit push button & basin outlet
 Fit the push button and basin outlet into the bench.
 Ensure the sealing o-ring is placed underneath the
push button and outlet body and the anti-rotation pin
locates properly.
 Secure underneath with the supplied cup washer and
back nut.
2. Assemble valve body
 Assemble the valve body to the push
button.
 Ensure to apply thread tape for sealing.
Take care not to over-tighten.
3. Fit flexi hose
 Connect water supply to isolation valve inlet.
4. Testing
 Push the button and ensure that there is
flow from the outlet.
 Inspect the tap and check for any leaks.
 Adjust flow with isolation valve, so
required flow is achieved

Version 1, 30 August 2018, 4 of 4
Version 1, 30 August 2018, 4 of 4
TROUBLESHOOTING
PROBLEM CAUSE RECTIFICATION
Inconsistent
flow
Blocked flow restrictor Remove isolation valve, remove flow restrictor & clean
with water
Dirt in the top assembly cartridge Remove cartridge, clean with water and re-grease
spindle if required.
Continuous
flow
Top assembly cartridge loose or
internally obstructed or damaged.
Remove cartridge, clean with water and re-grease
spindle if required.
Water is not
flowing from
tap
Supply not on Turn water on
Blocked flow restrictor Remove flow regulator from tap and remove debris.
Install an inline strainer to stop further blockages.
Rate of flow
inadequate
The flow restrictor may not be
satisfactory due to inadequate supply
pressure
Remove flow restrictor and replace with a flow restrictor
of different capacity to suit (available from Galvin
Engineering)
Button hard
to press The mains pressure may be too great Reduce to below 500kPa (70PSI), re-grease spindle if required
In the absence of a legal or industry definition of anti-ligature or ligature resistant products, when we use these terms, we are referring to
products that are designed and manufactured with the intention of reducing the risk of ligature attachment to the product(s).
Galvin Engineering Pty Ltd will always endeavour to design and test our anti-ligature product(s) to reduce the risk of product ligature attachment that may result in
serious injury or death.
Whilst all reasonable measures are taken at the time of design, the anti-ligature design of the products are not intended to and will not:
a. Replace protective measures that need to be taken in the specific circumstances of usage;
b. Substitute the need for supervision of those who may be at risk;
c. Protect and or prevent those at risk against any self-harm instances that may occur when installed; and
d. Protect and or prevent injury when the risks where unknown to us at the time of the design of the product(s).
Galvin Engineering Pty Ltd does not offer and does not represent or warrant that any product(s) for sale that are ligature-free.
Therefore, Galvin Engineering will not be liable for any claims, loss, or damages arising from ligature attachment on our products. It is the purchaser's responsibility
to ensure that products purchased and installed are suitable for the environments in which they are installed, and suitable supervision and protective measures are
in place to protect those at risk.
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty
Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied.
Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including but
not limited to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download
from www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free
from operational defects in workmanship and materials for the warranty period as shown on the schedule in
the manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any
defective products manufactured by Galvin Engineering without charge, so long as the terms of the
Manufacturer’s warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for
breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product.