Galvin Engineering 49920 User manual

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Document No.: 001.00.30.22
Version 1, 7 October 2022, Page 1of 4
Washing Machine Taps
PRODUCT CODES:
- 49920 (Vandal Resistant)
- 49924 (Vandal Resistant)
- 49820 (Vandal Resistant)
- 48785 (Stirling)
SPECIFICATIONS
−Vandal resistant handle featuring a locking ring to secure the handle to the spindle which may only be
removed using the key provided. (Vandal Resistant)
−Chrome plate finish for easy cleaning and added durability.
−Handle and button not included, have to be ordered separately. (Stirling)
IMPORTANT: All taps are tested in accordance with AS/NZS 3718 and leave our premises in
good working order.
TECHNICAL DATA
Inlet
½” BSP - Female
Outlet
¾” BSP - Male
Headwork
Jumper Valve
Working Pressure Range (kPa)
Min
50
Max
500
Working Temperature Range (°C)
Min
5
Max
80
Nominal Flow Rate (LPM)
N/A
Finish
Chrome
NOTE: Galvin Specialised continually strive to improve their products. Specifications may change without
notice.
TOOLS REQUIRED
−Power drill
−Spanner
−Hex key
−Thread tape

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 1, 7 October 2022, Page 2of 4
PRE-INSTALLATION - MOUNTING DETAILS
Wall Spud
−Wall spuds must be 15BSP MI and protrude from the finished wall by no more than 15mm
Note: In some situations a male thread connection on the tap may be more suited. If so, please
contact Galvin Specialised on 1300 514 074.
INSTALLATION
IMPORTANT: Galvin Specialised products must be installed in accordance with these installation
instructions and in accordance with AS/NZS 3500, the PCA and your local regulatory requirements. Water
and/or electrical supply conditions must also comply to the applicable national and/or state standards.
Failing to comply with these provisions shall void the product warranty and may affect the performance of
the product.
1. Fit washing machine body
−Fit the washing machine body assembly to the
spud and fasten with a spanner.
−We recommend using thread tape or
equivalent to ensure the connection does not
leak.
−DO NOT tighten the body by using the top
assembly.
2. Fit handle
−Ensure the spindle is in the closed position
then fit bonnet and handle
−Secure the handle using the “C” circlip and
locking ring.

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 1, 7 October 2022, Page 3of 4
3.Testing
−Once temperature indicator is fitted, check the operation of the unit and inspect for any leaks.
TROUBLESHOOTING
PROBLEM
CAUSE
RECTIFICATION
Taps are dripping water
Jumper valves are worn or damaged
Replace jumper valve
Tap seat is damaged
Refurbish tap seat using a
reseating tool.
Water is leaking from spindle
O-ring on jumper valve spindle is
damaged or worn
Replace o-ring
Water is not flowing from tap
Water is turned off
Turn water on
Spindle is difficult to turn
Build up of scale on spindle, spindle
worn or o-ring has been damaged
Remove jumper valve, clean and
regrease. Replace o-ring.
Complete SBA may need to be
replaced.
Handle is loose
Screw has come loose
Tighten locking ring
SERVICE AND MAINTENANCE
1. Turn off the water supply and turn on the tap handle to drain water from the bodies.
2. Remove the temperature indicator from the handle.
3. Remove the handle from the tap.
4. Unscrew the top assembly from the body.
5. Check the o-ring on the spindle and the
jumper valve for wear and damage.
Replace if required.
6. Clean the spindle and body of debris.
7. Place a new o-ring (if required) onto the spindle and re-grease with potable water approved grease.
8. Re-assemble top assembly. Follow the product installation guidelines for the relevant product to re-
assembly method.

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 1, 7 October 2022, Page 4of 4
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty
Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied.
Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including but
not limited to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download
from www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free
from operational defects in workmanship and materials for the warranty period as shown on the schedule in the
manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any defective
products manufactured by Galvin Engineering without charge, so long as the terms of the Manufacturer’s
warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for
breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product.