Galvin Engineering Ezy-Drink 35188X User manual

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 1, 25th October 2022, Page 1of 3
Ezy-Drink®SS Remote Drinking Bubbler Tap
Mouth Guard and Stem
PRODUCT CODES:
- 35188X
SPECIFICATIONS
−Bubbler Mouth Guard is designed to operate at full mains pressure.
−The rubber mouthguard is resistant to fungal and bacterial attack and has a high resistance to sunlight.
−Stainless Steel construction
IMPORTANT: All Ezy-Drink®remote bubbler taps are tested in accordance with AS/NZS 3718 and leave
our premises in good working order.
TECHNICAL DATA
Inlet
½” BSP - Male
Outlet
Rubber mouthguard
Headwork
N/A
Working Pressure Range (kPa)
Min
50
Max
500
Working Temperature Range (°C)
Min
5
Max
60
Nominal Flow Rate (LPM)
N/A
Finish
Stainless Steel/Rubber
NOTE: Galvin Specialised continually strive to improve their products. Specifications may change without
notice.
TOOLS REQUIRED
−Power drill
−Spanner or adjustable crescent

© Galvin Engineering Pty Ltd
Version 2, 12th July 2022, Page 2of 3
Product Installation Guidelines
Version 1, 25th October 2022, Page 2of 3
PRE-INSTALLATION - MOUNTING DETAILS
−If the mounting holes do not already exist, mark out and drill
the holes in the bench/trough, as shown in rough-in
dimensions.
Note: Before installation, all lines must be flushed.
We recommend that a line strainer be installed prior to drinking
taps to eliminate any foreign material.
INSTALLATION
IMPORTANT: Galvin Specialised products must be installed in accordance with these installation instructions and in
accordance with AS/NZS 3500, the PCA and your local regulatory requirements. Water and/or electrical supply conditions
must also comply to the applicable national and/or state standards. Failing to comply with these provisions shall void the
product warranty and may affect the performance of the product.
1. Disassemble Mouthguard Outlet
−Remove back nut and cup washer from the
mouthguard outlet assembly
2. Fit Mouthguard Outlet
−Ensure the sealing rubber washers are placed
underneath the mouthguard outlet.
−Fit the mouthguard outlet into the trough.
Rough-In Dimensions
*Only drill Ø2.5mm hole if anti-
rotation pin (not supplied) is
required.

© Galvin Engineering Pty Ltd
Version 2, 12th July 2022, Page 3of 3
Product Installation Guidelines
Version 1, 25th October 2022, Page 3of 3
3. Secure Mouthguard Outlet
−Secure the mouthguard outlet underneath with the supplied cup washer and back nut.
−Use thread tape/sealant when connecting mains water.
−Once fitted, test for leaks and correct operation.
TROUBLESHOOTING
PROBLEM
CAUSE
RECTIFICATION
Inconsistent flow
Blocked outlet
Remove outlet and clean
Water is not flowing from outlet
Water is turned off
Turn on water
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty Ltd.
With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied. Galvin
Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including but not
limited to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download from
www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free from
operational defects in workmanship and materials for the warranty period as shown on the schedule in the
manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any defective
products manufactured by Galvin Engineering without charge, so long as the terms of the Manufacturer’s
warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for
breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product.