Galvin Engineering GalvinCare CP-BS Lead Safe 121.35.64.00 User manual

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 1, 2 February 2022, Page 1of 4
GalvinCare®CP-BS Lead Safe™ Mental Health
Anti-Ligature ShowerRose 100mm Bolting Plate
PRODUCT CODES:
- 121.35.64.00
SPECIFICATIONS
−The GalvinCare®Vandal Resistant Shower Rose 65 provides anti-vandalism and anti-ligature features.
−Used extensively in high risk, high security applications such as prisons, correctional facilities, and
detention centres.
−Designed for maximum protection against vandalism.
−Constructed from heavy duty components and comes complete with special tamper resistant screws.
−For use with high pressure plumbing systems between 150 & 500kPa.
−Special consideration may be required when used with low water pressure systems and components.
−Chrome plate finish.
−*
IMPORTANT: All GalvinCare®Vandal Resistant Shower Roses are tested in accordance with AS/NZS
3662 and leave our premises in good working order.
*As ‘lead free’ is not currently defined by low in Australia and New Zealand, we have based our definition of Lead Safe™ on the requirements of s1417 of the USA’s Safe Drinking Water Act
(SDWA) and the relevant US standards NSF61 / NSF372. The SDWA defines ‘lead free’ as “not more than a weighted average of 0.25% lead when used with respect to the wetted surface of
pipes, pipe fittings, plumbing fittings and fixtures”.
TECHNICAL DATA
Inlet
 BSP - Female
Outlet
Shower Rose
Headwork
N/A
Working Pressure Range (kPa)
Min
150
Max
500
Working Temperature Range (°C)
Min
5
Max
70
Nominal Flow Rate (LPM)
6.6
Finish
Chrome
NOTE: Galvin Engineering continually strive to improve their products. Specifications may change without
notice.

© Galvin Engineering Pty Ltd
Version 3, 2 February 2022, Page 2of 4
Product Installation Guidelines
Version 1, 2 February 2022, Page 2of 4
PRE-INSTALLATION
MOUNTING DETAILS HOLE CENTRES
−The rough in details show correct fitment of the Vandal
Resistant Shower unit.
−A 60mm X 60mm wall cutout with a depth of a least 12mm is

−Recommended installation height above floor

INSTALLATION
INSTALLATION COMPLIANCE: Galvin Engineering products must be installed in accordance with these
installation instructions and in accordance withAS/NZS 3500, the PCA and your local regulatory requirements.
Water and/or electrical supply conditions must also comply to the applicable national and/or state standards.
Failing to comply with these provisions shall void the product warranty and may affect the performance of the
product.
IMPORTANT: Whilst our product designs take into account a broad range of installation types and surfaces,
it is important that surfaces which fixtures are mounted to are flat and free from defect. Additionally, ensure
any protruding connecting thread is square to the wall so that the outlet sits flat against the wall when installed,
ensuring that there are no gaps between the wall and outlet. This is especially important when installing
product ranges that havebeen designed for correctional and healthfacilities, where special attention is required
to minimise ligature points and areas for concealment of contraband. In addition to ensuring the products are
fitted securely and in accordance with the following instructions, consideration shall be given to the use of non-
pick mastics such as BASF Sonolastic “Ultra” to ensure a high quality and safe installation.
1. Fit rawlnuts
−Drill holes as detailed in the mounting details.
−Push the four supplied rawlnuts into the drilled
holes in the wall.
2. Align shower body and plate
- Align the shower body and plate onto the holes.
Ensuring to apply sealant to create a water tight
seal between plate and wall.



























© Galvin Engineering Pty Ltd
Version 3, 2 February 2022, Page 3of 4
Product Installation Guidelines
Version 1, 2 February 2022, Page 3of 4
3. Secure the faceplate
- Secure the face plate with the provided M6
Button Head Post Torx Screw.
4. Connect Water supply from the back
−From the back of the wall connect the water
supply. Ensuring to apply thread tape or sealant
to create a water tight seal.
TESTING
−Turn on water supply, inspect the tap and check for any leaks.
Note: Never operate without a flow restrictor, as GalvinCare®Vandal Resistant
Shower Rose will deliver full mains pressure with unrestricted flow.




Version 3, 2 February 2022, Page 4of 4
Product Installation Guidelines
Version 1, 2 February 2022, Page 4of 4
TROUBLESHOOTING
PROBLEM
CAUSE
RECTIFICATION
Shower is dripping water
Head-works are worn or
damaged
Remove and inspect the head-works,
remove debris and/or replace head parts
if damaged
Inconsistent flow
Blocked flow restrictor
Remove flow regulator from body and
remove debris. Install an inline strainer
to stop further blockages.
Leak from behind body
Insufficient sealant
Apply more sealant
Water is not flowing from tap
Water is turned off
Turn on water
Rate of flow inadequate
The flow restrictor may not be
satisfactory due to inadequate
supply pressure
Remove flow restrictor and replace with
a flow restrictor of different capacity to
suit (available from Galvin Engineering)
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty
Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied.
Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including but
not limited to the implied warranties of merchantability and fitness for a particular purpose.

from www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free
from operational defects in workmanship and materials for the warranty period as shown on the schedule in

defective products manufactured by Galvin Engineering without charge, so long as the terms of the

The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for
breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product.