Galvin Engineering Ezy-Wash TF81HJS Instruction sheet

Version 1, 3 August 2017, Page 1 of 5
Version 2, 3 August 2017, Page 1 of 5
Ezy-Wash® Pre-Rinse Tapware
PRODUCT CODE:
- TF81HJS
- TF81HJP
TF81HJS TF81HJP
SPECIFICATIONS
 Galvin Specialised recommends the installation of strainers and pressure reducing valves prior to installing
the pre-rinse unit to ensure clean consistent water supply. Debris or poor water quality could cause the
trigger to seize or fail to seal.
 This pre-rinse unit has a 6 star WELS rating, the Pot Filler attachments are 0 star to allow fast pot filling.
TECHNICAL DATA
Inlet ½” BSP – Male
Outlet TF81HJS Trigger Spray
TF81HJP Trigger Spray & Pot Filler
Headworks TF81HJS Jumper Valve
TF81HJP Jumper Valve
Working Pressure Range (kPa) Min 100
Max 500
Working Temperature Range (°C) Min 5
Max 65
Nominal Flow Rate (LPM) TF81HJS 3.5
TF81HJP 15
Finish Chrome
NOTE: Galvin Specialised continually strives to improve their products. Specifications may change without
notice. Higher temperature or pressures could result in premature failure and void the manufacturer’s warranty.
TOOLS REQUIRED
 Adjustable spanner
 Hex key
 Power drill

Version 1, 3 August 2017, Page 2 of 5
Version 2, 3 August 2017, Page 2 of 5
PRE-INSTALLATION
Body:
 If the mounting hole does not already exist,
mark out and drill the hole in the bench, as
shown.
 This model is a single inlet unit requiring a hole
diameter of 23 to 26mm. Ensure 70mm
minimum between wall and hole center as
shown “A”.
 Maximum bench thickness is 50mm.
Wall Bracket:
 Mark out the three (3) holes for mounting the
wall bracket assembly at a height of between
430mm min - 520mm max directly up from the
bench. Cut out or drill as shown in the image.
(Supplied fasteners may not be suitable for the
mounting surface. If this is the case, suitable
fasteners will need to be sourced by the
installer)
Note: We recommend the wall bracket is installed
at the maximum of 520mm. The wall bracket can be
mounted lower at a height of up to 90mm below the
circlip. However, the further it is mounted away
from the circlip, the more the stability of the unit is
compromised.
MOUNTING DETAILS
TF81HJS – Assembly
TF81HJP - Assembly

Version 1, 3 August 2017, Page 3 of 5
Version 2, 3 August 2017, Page 3 of 5
INSTALLATION
INSTALLATION COMPLIANCE: Galvin Specialised products must be installed in accordance with these
installation instructions and in accordance with AS/NZS 3500, the PCA and your local regulatory requirements.
Water and/or electrical supply conditions must also comply to the applicable national and/or state standards.
Failing to comply with these provisions shall void the product warranty and may affect the performance of the
product.
1. Measure and cut support rod
 Measure the distance between the wall mounting
surface and the centre line of the drilled hole in
the bench/trough (dimension “A”).
 Take dimensions “A” and subtract 16mm. This is
the required length of the support rod (Required
support rod length = A-16mm).
 Cut the support rod accordingly; ensure the
threaded end is NOT cut off.
Note: Distance “A” must be no less than 70mm.
The support rod length can be 70mm min. to 285mm
max. (If it is more than 285mm, an extension support
rod must be purchased)
2. Fit wall bracket
 Secure the wall bracket to the wall.
 Supplied fasteners may not be suitable for
the mounting surface. If this is the case,
suitable fasteners will need to be sourced.
Note: The wall bracket must be mounted with three
screws for stability and strength. This is critical
and failure to do this may void the warranty.
3. Fit support rod
 If pot filler kit (TF81HJP) has been purchased, it
must be attached to the pre-rinse unit prior to
fitting the support rod to the riser. Refer to the
installation instruction supplied with the pot
filler.
 Screw support rod into the riser hook and
ensure it is not fully tightened.
4. Fit upper riser to lower riser
 Remove protective cap from upper riser
spindle.
 Fit the upper riser to the lower riser, ensure
the sealing o-rings are inside the spindle.
 Tighten with new supplied grub screw.
 It is critical that the grub screw point
locates accurately into hole recess of
mating part. Failure to do so may result in
damage and/or failure of the unit.

Version 1, 3 August 2017, Page 4 of 5
Version 2, 3 August 2017, Page 4 of 5
TF81HJS TF81HJP
TF80H-S TF80HJP
5. Fit pre-rinse riser assembly
1. Fit compression nut to support rod, followed
by the compression cone and locate the
support rod into wall bracket.
2. Fit the pre-rinse riser assembly through the
drilled hole on the bench.
6. Secure pre-rinse assembly
 Secure pre-rinse assembly with the supplied
flanged back nut; ensure the sealing rubber
washer is placed underneath the pre-rinse
body flange.
TF81HJS TF81HJP
7. Secure support rod
1. Fasten support rod securely against riser.
2. Tighten compression nut on wall bracket to
secure the support rod. The rod is now rigid.
8. Test unit
 Once all fittings have been tightened
securely, connect the unit to the mains
water.
 Turn on water and test the unit for any
leaks.

Version 2, 3 August 2017, Page 5 of 5
WARNINGS
For optimum performance it is recommended that the isolation or mains taps are turned off whilst the unit is
not in use (overnight etc.), so that the unit is not under mains pressure when unsupervised. Flood damage
may occur if a failure occurs whilst the unit is under mains pressure (warranty is void in this instance).
Galvin Specialised recommends that the handpiece is periodically serviced by a qualified plumber.
IMPORTANT:
To seal the hose this unit uses Loctite 577 which is a thread sealant approved for use with potable water
(AS/NZS 4020). If hose is to be removed for maintainance purposes, reseal the joints with Loctite 577, or
an equivalent sealant compliant with AS/NZS 4020. Do not use thread tape to seal the hose connections, as
this may cause the hose nut to become loosened over time and leak.
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty
Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied.
Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including but
not limited to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download from
www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free from
operational defects in workmanship and materials for the warranty period as shown on the schedule in the
manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any defective
products manufactured by Galvin Engineering without charge, so long as the terms of the Manufacturer’s
warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for
breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product