Galvin Engineering Ezy-Drink 316 TDBFXEB Instruction sheet

Product Installation Guideline
Ezy-Drink GalvinClear®Remote Electronic Drinking
Tapware
PRODUCT CODES:
- TD25XEB (Drinking Bubbler) - TDBFXEB (Bottle Filler)
SPECIFICATION
-Piezo button activation
-Stainless steel construction
IMPORTANT: All Ezy-Drink®remote bubbler taps are tested in accordance with AS/NZS 3718 and leave our premises in
good working order
TECHNICAL DATA
TDBFXEB TD25XEB
Inlet 1/2” BSP - Female 1/2” BSP - Female
Outlet Bottle Filler Metal Mouthguard
Headwork Solenoid Solenoid
Working Pressure Range (kPa) Min 30 30
Max 1000 1000
Working Temperature Range (°C) Min 2 2
Max 65 65
Nominal Flow Rate (LPM) 2 2
Power supply
Type Battery Battery
Input N/A N/A
Output 6V DC 6V DC
Cable Length 40mm 40mm
Sensor
Type Piezo Piezo
Activation Piezo Button Piezo Button
Connection 6mm 2 Pin Plug 6mm 2 Pin Plug
Cable 0.165m 0.165m
Controller
Input Voltage 6V DC 6V DC
Power Consumption Standard Standard
Cable Length 0.165M 0.165M
Solenoid
Connection Inlet 1/2” BSP - Female 1/2” BSP - Female
Outlet 1/2” BSP - Male 1/2” BSP - Male
Working Pressure Range (kPa) Min 30 30
Max 1000 1000
Working Temperature Range (°C) Min 2 2
Max 80 80

Product Installation Guideline
MOUNTING DETAILS - OVERALL DIMENSIONS
TD25XEB TDBFXEB
PRE-INSTALLATION
MOUNTING DETAILS - ROUGH IN DIMENSIONS
Ø23 NOM
Ø19
PIEZO
BUTTON
BUBBLER OR
JUG FILLER
INSTALLATION
IMPORTANT: Galvin Engineering products must be installed in accordance with these installation instructions
and in accordance with AS/NZS 3500, the PCA and your local regulatory requirements. Water and/or electrical
supply conditions must also comply to the applicable national and/or state standards. Failing to comply with these
provisions shall void the product warranty and may a󰀨ect the performance of the product.
1. Fit Body & Mouthguard Outlet
-Remove the lock nut.
-Fit the body into the trough ensuring the rubber
o-ring is placed between the trough and the body.
-Secure outlet underneath with the supplied back
nut and tighten the screws using a 2.5mm hex key
-Take care not to over-tighten.
2. Fit Flexi Hose
-Fit the exi hose to solenoid as shown.

Product Installation Guideline
3. Fit the Touch Button
-Fit the touch button and coloured washer into the
pre-drilled hole.
NOTE: Ensure the o-ring is between the button
and the coloured washer.
-Secure using the supplied nut.
4. Connect the Touch Button to the Controller
-Connect the controller to the Solenoid
and the battery pack.
OPERATION
1. Turn water on 2. Turn water “OFF” 3. Auto shut “OFF”
SET WATER FLOW DURATION
1. Press button 4x 2. Wait 5 Seconds 3. Turn water ON then OFF
4. Press button 5x 5. Water will run 6. After required ow duration
(2-180 sec) press button again
7. OK

Product Installation Guideline
SET 24/48/72 Hour Automatic Flush
1. Press button 6x 2. Wait 5 Seconds
3. Turn water ON then OFF
4. Press button 6x
5. Wait 5 secs
6. Turn water ON then OFF
7. Times for desired auto ush 8 After required ow duration
(2-180 sec) press button again.
9. 10. OK

Product Installation Guideline
Within Australia: 1300 514 074 Outside Australia: P: [phone]
F: [phone]
[email protected]
www.galvinengineering.com.au
ABN: 78 008 719 382
PERTH I SYDNEY I MELBOURNE I BRISBANE I ADELAIDE
Quality
ISO 9001
Environment
ISO 14001
Product Installation Guideline
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty Ltd. With respect
to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied. Galvin Engineering Pty. Ltd.
hereby specically disclaims all other warranties, express or implied, including but not limited to the implied warranties of
merchantability and tness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download from www.
galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free from operational defects
in workmanship and materials for the warranty period as shown on the schedule in the manufacturer’s warranty. During the
warranty period, Galvin Engineering will replace or repair any defective products manufactured by Galvin Engineering without
charge, so long as the terms of the Manufacturer’s warranty are complied with.
The remedy described in the rst paragraph of this warranty shall constitute the sole and exclusive remedy for breach of
warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or consequential damages,
including without limitation, lost prots or the cost of repairing or replacing other property which is damaged if this product
does not work properly, other costs resulting from labour charges, delays, vandalism, negligence, fouling caused by
foreign material, damage from adverse water conditions, chemical, electrical or any other circumstances over which Galvin
Engineering has no control. This warranty shall be invalidated by any abuse, misuse, misapplication, improper installation or
improper maintenance or alteration of the product.