Galvin Engineering Ezy-Drink TD25XEB User manual

Version 214 April 2021, Page 1of 5
Version 2, 23rd March, Page 1of 5
Ezy-Drink®GalvinClear SS316 Remote Electronic
Drinking Bubbler Metal Tap - Battery
PRODUCT CODES:
- TD25XEB
SPECIFICATIONS
−Piezo button activation
−Stainless steel construction
IMPORTANT: All Ezy-Drink®remote bubbler taps are tested in accordance with AS/NZS 3718 and leave
our premises in good working order.
TECHNICAL DATA
Inlet
 BSP - Female
Outlet
Metal mouthguard
Headwork
Piezo Activation
Working Pressure Range (kPa)
Min
50
Max
500
Working Temperature Range (°C)
Min
5
Max
60
Nominal Flow Rate (LPM)
1.7
Solenoid
Input Voltage
6 V DC
Power Consumption
-
Connection
Inlet
- Female
Outlet
- Male
Pressure Range
(kPa)
Min
50
Max
500
Temperature
(°C)
Min
5
Max
60
Finish
Stainless Steel
NOTE: Galvin Specialised continually strive to improve their products. Specifications may change without
notice.

Version 2, 23rd March 2021, Page 2of 5



 















PRE-INSTALLATION
MOUNTING DETAILS –ROUGH IN DIMENSIONS
MOUNTING DETAILS –OVERALL DIMENSIONS
Controller programming is locked. If specific changes need to be made, contact Galvin Specialised.
If the mounting holes do not already exist, mark out and drill the holes in the bench/trough, as shown in rough-
in dimensions.
Note: Supplied flexi hose length is 250mm long.
Note: Before installation, all lines must be flushed. We recommend that a line strainer be installed prior to drinking
taps to eliminate any foreign material.
 
BUBBLER
PIEZO
BUTTON

Version 2, 23rd March 2021, Page 3of 5
INSTALLATION
IMPORTANT: Galvin Engineering products must be installed in accordance with these installation instructions
and in accordance with AS/NZS 3500, the PCA and your local regulatory requirements. Water and/or electrical
supply conditions must also comply to the applicable national and/or state standards. Failing to comply with
these provisions shall void the product warranty and may affect the performance of the product.
1. Fit Body & Mouthguard Outlet
−Remove the lock nut.
−Fit the body into the trough ensuring the
rubber o-ring is placed between the
trough and the body.
−Secure outlet underneath with the
supplied back nut and tighten the screws
using a 2.5mm hex key
−Take care not to over-tighten.
2. Fit Solenoid and Outlet
−Fix the solenoid in position ensuring that the
solenoid coil is not facing downwards.
−Fit the flexi hose to solenoid outlet and bubbler.
−Connect water supply to solenoid inlet.
3. Fit the Piezo Button
−Fit the piezo button and coloured washer
into the pre-drilled hole.
NOTE: Ensure the o-ring is between the
button and the coloured washer.
−Secure using the supplied nut.
4. Connect the Piezo Button to the Controller
−Connect the controller to the solenoid, piezo button
and battery pack.
Solenoid
Coil

Version 2, 23rd March 2021, Page 4of 5
5. Testing and Flow Adjustment
−Once the drinking tap has been installed and tested for leaks, the water height may be adjusted to suit
the available pressure as shown above.
−To adjust water flow
1. Remove the blanking screw.
2. Adjust the water height by turning the regulating screw.
3. Once desired height has been achieved, replace blanking screw.
Note: The full range from minimum flow to maximum flow is only ¼ turn.
Regulating Screw
Blanking Screw

Version 2, 23rd March 2021, Page 5of 5
TROUBLESHOOTING
PROBLEM
CAUSE
RECTIFICATION
Water is not flowing from
tap
Water is turned off
Turn on water
Blocked flow regulating screw
Remove regulating screw and clean
Rate of flow inadequate
The flow regulating screw may
not be adjusted correctly
Remove blanking screw and adjust flow
regulating screw as described above
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty
Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied.
Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including but
not limited to the implied warranties of merchantability and fitness for a particular purpose.
able for download
from www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free
from operational defects in workmanship and materials for the warranty period as shown on the schedule in the
y. During the warranty period, Galvin Engineering will replace or repair any defective

warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for
breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product.