Galvin Engineering GalvinAssist CP User manual

Product Installation Guidelines
© Galvin Engineering Pty Ltd
Version 1, 25th May 2022, Page 1of 6
GalvinAssist®CP Hand Shower Kit W/-900 x 32
SS Hygienic G/Rail, ClevaCare Shw & CliniLever Tap
PRODUCT CODES:
- CLEVAKIT1CP
SPECIFICATIONS
- CP Brass swing arm with stainless steel spring.
- Supplied with stainless steel fasteners.
- Finished in bright chrome plate for easy cleaning and added durability.
IMPORTANT: All Galvin Engineering taps are tested in accordance with AS/NZS 3718 and leave our
premises in good working order.
TECHNICAL DATA
Inlet
½” BSP –Female
Outlet
Handheld Shower
Headwork
Ceramic Cartridge
Working Pressure Range (kPa)
Min
150
Max
500
Working Temperature Range (°C)
Min
5
Max
55
Nominal Flow Rate (LPM)
8.24
Finish
Chrome
NOTE: Galvin Specialised continually strive to improve their products. Specifications may change
without notice.
TOOLS REQUIRED
−Power drill
−Spanner or adjustable crescent
−Hex Key
−Thread Tape

© Galvin Engineering Pty Ltd
Version 1, 1 June 2022, Page 2of 6
Product Installation Guidelines
Version 1, 25th May 2022, Page 2of 6
PRE-INSTALLATION
MOUNTING DETAILS
−If the mounting holes do not already exist, mark out and drill the holes as shown in rough-
in dimensions.
For Tapware
Wall body
−Wall body must be G5/8” FI and body should be
between 0 and 15mm behind the finished
wall surface.
0 to 15mm
G 5/8”

© Galvin Engineering Pty Ltd
Version 1, 1 June 2022, Page 3of 6
Product Installation Guidelines
Version 1, 25th May 2022, Page 3of 6
INSTALLATION
INSTALLATION COMPLIANCE: Galvin Engineering products must be installed in accordance with these
installation instructions and in accordance with AS/NZS 3500, the PCA and your local regulatory
requirements. Water and/or electrical supply conditions must also comply to the applicable national and/or
state standards. Failing to comply with these provisions shall void the product warranty and may affect the
performance of the product.
1. Top Flange
Mark the height of the top flange centre point by
measuring vertically 2275mm above the floor. Then
measure approximately 150mm horizontally to the
left or right (depending on the position of the
shower recess) of the centre of the existing supply
fitting. Drill 2 holes Ø8 x 50mm deep, 38mm
horizontally apart to suit the top flange.
2. Bottom Flange
Mark the position of the bottom flange’s centre point
400mm below the top flange’s centre point. Then mark
the two holes for mounting the bottom flange in a
similar manner to the top flange.
Note: The bottom flange is mounted in a vertical
orientation.
Important: the functionality of this product relies on the
accuracy of the vertical alignment between the top and
bottom flanges.
3. Mount the shower arm
Attach both the wall flanges using the plastic star
plugs and self-tapping screws supplied (these
fasteners may not be appropriate for all wall
materials. If this is the case, other fastening
systems will have to be sourced by the installer).
4. Attach the hose
When fitting the inlet hose, lay the arm against the wall
in the preferred ‘resting’ position, then tighten the
hose. The arm will tend to return to this position when
not in use.
38
DRILL 2 HOLES
Ø8x50 DEEP
2275mm ABOVE
THE FLOOR

© Galvin Engineering Pty Ltd
Version 1, 1 June 2022, Page 4of 6
Product Installation Guidelines
Version 1, 25th May 2022, Page 4of 6
Clevakit typical installation
Conforming to AS1428.1-2009
5. Check Shower for operation and leaks
Check the hose is securely connected. Turn on
water supply. Once installation is completed, the
unit must be tested for any leaks.
Notes:
1. To comply with backflow prevention
standards, the hand spray must hang at least
55mm above the floor providing an ‘air-gap’. If
the hand piece lies on the floor, then an
appropriate backflow prevention device must
be installed.
2. Shown is a Clevakit typical installation
conforming to AS1428.1-2009.
For Tapware
6. Fit spindle assembly
−Remove handle and flange from cartridge
assembly. Unscrew the ¼ turn ceramic head
part from the threaded sleeve assembly and
screw ceramic cartridge into the valve body by
hand, tighten using a 17mm spanner.
−Refit threaded sleeve and spindle.
The ¼ turn ceramic head part MUST be fitted into
the wall body prior to refitting the threaded
sleeve and spindle. DO NOT tighten cartridge by
using the spindle or the threaded sleeve.
7. Fit wall flange
−Ensure o-ring is fitted to the bottom of the
wall flange, and then hand-tighten the wall
flange onto the threaded sleeve.

© Galvin Engineering Pty Ltd
Version 1, 1 June 2022, Page 5of 6
Product Installation Guidelines
Version 1, 25th May 2022, Page 5of 6
8. Fit handle
−Ensure the spindle is in the closed
position and firmly press the lever handle
onto the spindle in the desired
orientation.
−Check operation of lever handle. It
should turn freely for a full ¼ turn.
−Secure the handle in position using the
supplied washer and stainless-steel cap
screw.
9.Fit water temperature indicator & Test
−Once the lever handle is secure; fit the
appropriate water temperature indicator.
−Check the operation of the unit and inspect
for any leaks.
TROUBLESHOOTING
PROBLEM
CAUSE
RECTIFICATION
Water is not flowing or
inconsistent flow
Shower arm is blocked with
debris.
Remove debris from shower arm.
Leak from hose
connection
Hose connection loose
Check wall coupling locates properly with
hose connection.
Taps are dripping water
Ceramic discs are worn or
damaged
Remove and inspect SBA. Remove
debris and/or replace SBA if damaged.
Tap seat is damaged
Refurbish tap seat using a reseating tool.
Water is leaking from
spindle
O-ring on jumper valve spindle
is damaged or worn
Replace o-ring
Water is not flowing from
tap
Water is turned off
Turn on water
Aerator or flow regulator is
blocked by debris
Remove aerator and/or flow regulator
from tap and remove debris. Install an
inline strainer.
Spindle is difficult to turn
Build up of scale on spindle,
spindle worn or o-ring has
been damaged
Remove cartridge sleeve, clean and
regrease. Replace o-ring. Complete SBA
may need to be replaced.
Handle is loose
Screw has come loose
Tighten handle screw
Flange does not screw
down onto wall surface
Wall bodies are set too far out
Re-position tap bodies

© Galvin Engineering Pty Ltd
Version 1, 1 June 2022, Page 6of 6
Product Installation Guidelines
Version 1, 25th May 2022, Page 6of 6
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin
Engineering Pty Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties,
express or implied. Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties,
express or implied, including but not limited to the implied warranties of merchantability and fitness for a
particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for
download from www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the
product is free from operational defects in workmanship and materials for the warranty period as shown
on the schedule in the manufacturer’s warranty. During the warranty period, Galvin Engineering will
replace or repair any defective products manufactured by Galvin Engineering without charge, so long as
the terms of the Manufacturer’s warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive
remedy for breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any
incidental, special or consequential damages, including without limitation, lost profits or the cost of
repairing or replacing other property which is damaged if this product does not work properly, other
costs resulting from labour charges, delays, vandalism, negligence, fouling caused by foreign material,
damage from adverse water conditions, chemical, electrical or any other circumstances over which
Galvin Engineering has no control. This warranty shall be invalidated by any abuse, misuse,
misapplication, improper installation or improper maintenance or alteration of the product.