Galvin Engineering Ezy-Drink Lead Safe 170.81.13.01 Instruction sheet

Version 1, 12th March 2020 Page 1of 4
Ezy-Drink®Lead Safe™ Remote Push
Button Drinking Tap
PRODUCT CODES:
- 170.81.13.01
SPECIFICATIONS
Drinking taps are designed to operate at full mains pressure.
The rubber mouthguard is resistant to fungal and bacterial attack and has a high resistance to sunlight.
Adjustable built-in flow restrictor.
Made from Lead Safe™DR brass
IMPORTANT: All Ezy-Drink®remote bubbler taps are tested in accordance with AS/NZS 3718 and leave
our premises in good working order.
As ‘lead free’ is not currently defined by low in Australia and New Zealand, we have based our definition of Lead Safe™ on the requirements of s1417 of the USA’s Safe Drinking Water Act
(SDWA) and the relevant US standards NSF61 / NSF372. The SDWA defines ‘lead free’ as “not more than a weighted average of 0.25% lead when used with respect to the wetted surface of
pipes, pipe fittings, plumbing fittings and fixtures”.
TECHNICAL DATA
Inlet
½” BSP - Female
Outlet
Rubber mouthguard
Headwork
Push Button
Working Pressure Range (kPa)
Min
50
Max
500
Working Temperature Range (°C)
Min
5
Max
60
Nominal Flow Rate (LPM)
1.7
Finish
Chrome
NOTE: Galvin Specialised continually strive to improve their products. Specifications may change without
notice.
TOOLS REQUIRED
Power drill
Spanner or adjustable crescent
Screw driver

v
Version 1, 12th March 2020 Page 2of 4
190 MAX
28
33
ROUGH-IN DIMENSIONS
OUTLETINLET BODY
THISDRAWINGISTHEPROPERTYOFGALVINENGINEERINGANDSHALLBERETURNEDONDEMAND.ITMUSTNOTBEREPRODUCED,COPIEDORCOMMUNICATEDTOANYOTHERPARTYNORBEUSEDFORANYPURPOSEOTHERTHANSTATEDINTHEPARTICULARENQUIRYORDERORCONTRACTWITHWHICHITISUSED.
FORM07-03.13
TD15C
AS/NA
1047g
WEIGHT:
FINISH
MATERIAL:#
CCOPYRIGHTRESERVED:
APPD
DATE
DESCRIPTION
REV
NOTTOSCALE
IFINDOUBTASK
DRAWINGNO
SHEET1OF1
SCALE
MANUFACTUREDTO:
ISSUED APPD
CKD DRN
TITLE
410VICTORIARDMALAGAWAABN:78008719382
±1.0
±0.05
±0.1
.XX
REVISION:
.X
X
TOLERANCES
UNLESSOTHERWISESTATED
ALLDIMENSIONSINMM
27.0
PRE-INSTALLATION - MOUNTING DETAILS
If the mounting holes do not already exist, mark out and drill
the holes in the bench/trough, as shown in rough-in
dimensions.
Note: Supplied flexi hose length is 225mm long.
Maximum distance between outlet and push button is 180mm.
Note: Before installation, all lines must be flushed.
We recommend that a line strainer be installed prior to drinking
taps to eliminate any foreign material.
ROUGH-IN DIMENSIONS
INSTALLATION
IMPORTANT: Galvin Specialised products must be installed in accordance with these installation instructions
and in accordance with AS/NZS 3500, the PCA and your local regulatory requirements. Water and/or electrical
supply conditions must also comply to the applicable national and/or state standards. Failing to comply with these
provisions shall void the product warranty and may affect the performance of the product.
1. Disassemble Handle and Mouthguard Outlet
Remove the push button and dress flange from
the inlet body.
Do not remove the whole top assembly
Remove back nut and cup washer from the
mouthguard outlet assembly
2. Fit Inlet Body & Mouthguard Outlet
Ensure the sealing rubber washers are placed
underneath the inlet body and mouthguard outlet.
Fit the inlet body and mouthguard outlet into the trough.
Fit washer, flange & locknut onto inlet body and hand
tighten.
180 MAX
INLET BODY
MOUTHGUARD
OUTLET

v
Version 1, 12th March 2020 Page 3of 4
3. Secure Inlet Body and Mouthguard Outlet
Tighten the screws on the inlet body as shown.
Do not overtighten.
Secure the mouthguard outlet underneath with the
supplied cup washer and back nut.
4. Fit handle
Position and fit the handle and grub screw as shown.
Tighten firmly using the supplied hex key.
5. Fit Flexi-hose
Fit flexi-hose to mouthguard outlet and inlet body
as shown.
6. Testing
Once the drinking tap has been installed and tested for
leaks, the water height may be adjusted to suit the
available pressure.
To adjust water flow
1. Remove the blanking screw .
2. Adjust the water height by turning the regulator screw
.
3. Once desired height has been achieved, replace
blanking screw.
Note: The full range from minimum flow to maximum flow is
only ¼ turn.
Water
Supply

v
Version 1, 12th March 2020 Page 4of 4
TROUBLESHOOTING
PROBLEM
CAUSE
RECTIFICATION
Inconsistent flow
Blocked top assembly
Remove top assembly and clean
Water is not flowing from
tap
Water is turned off
Turn on water
Blocked flow regulating screw
Remove flow regulating screw and
clean
Continuous flow
Top assembly loose or
internally obstructed or
damaged
Remove top assembly, clean with water
and re-grease spindle if required
Rate of flow inadequate
The flow regulating screw may
not be adjusted correctly
Remove blanking screw and adjust flow
regulating screw as described above
Button hard to press
The mains pressure may be
too great
Reduce to below 500kPa (70PSI). Re-
grease spindle if required
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty
Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied.
Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including
but not limited to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download
from www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free
from operational defects in workmanship and materials for the warranty period as shown on the schedule in
the manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any
defective products manufactured by Galvin Engineering without charge, so long as the terms of the
Manufacturer’s warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy
for breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product.