Gazebo penguin 41215-32 User manual

ZZZ-183.41215-32.1127-15.GP.EN.HER.doc HER-HP 1
41215-32
12 X 15 SOLARIUM
ASSEMBLY INSTRUCTIONS
Two or more adults required for assembly
Base Dimensions 12’ ½”x15’6”, Largest Dimensions 13’6”x16’11” (see pg.14)
Overall Height 110’’
[e-mail]

ZZZ-183.41215-32.1127-15.GP.EN.HER.doc HER-HP 2
Before you assemble the Solarium
It is important that this solarium be installed on a solid base with the provided
screws. Otherwise, please ensure that you use anchors sufficient for your surface.
The solarium should not be installed adjacent to trees or a sloped roof. Snow and
ice may slide onto the solarium and cause it to collapse.
Tools needed:
Step ladder
#2 Phillips screwdriver (supplied)
Rubber mallet
Based on the location, decide where you would like to position the two (2) doors panels
which can slide open to the left or the right, your choice.
Slide left to open
Slide right to open

ZZZ-183.41215-32.1127-15.GP.EN.HER.doc HER-HP 3
12x15 Solarium Assembly Instructions
Step 1:
Before starting to assemble, please decide where you would like to position the door panels.
1. Stand up two regular frames (A), using two connecting pieces (E) and affix the panels (A)
together.
2. Stand up a frame meant to be next to the door (B) and a door frame (D), placing the door frame
either on the left or right, then use two connecting pieces (E) to affix the panel and door frame.
3. When assembling angled panels (A, D), you should put the two panels at 135 degree angle then
use the angled connecting pieces (I) and (J) to affix the panels together.

ZZZ-183.41215-32.1127-15.GP.EN.HER.doc HER-HP 4
Step 2:
1. Slide top door rail (F) into wheels of sliding door.
2. Slide lower door rail (G) into the plastic guide of the sliding door (C).
3. Use bold (Bb) to affix the plastic stoppers (H) one on each end of top door rail (F).
4. Use screw (Oo) to affix upper door rail end caps (Nn) one on each end of top door rail (F).
Step 3: Please note the sliding door should be installed from the inside of the solarium.
1. Place a bolt (Ww) and washer (Gg) through the top door rail (F) and door frame, and place a female
bolt (Cc-2) from the other side. Once all are inserted, tighten them all securely.
2. Secure the bottom door rail (G), using a bolt (Cc) with a washer (Gg).
3. Paying careful attention to whether it is the left (Dd-L) or right (Dd-R) latch, use bolt (Bb) to affix
the door latch onto the frame.
Repeat steps 2 and 3 for the second door.
Ww
Ww

ZZZ-183.41215-32.1127-15.GP.EN.HER.doc HER-HP 5
Step 4:
1. Attach roof rafters (L) to the central hub (N) using bolt (Bb).
2. Use screw (Z) to affix the rafters (L) onto the top of panels going through the metal piece attached
to the rafter (L).
Note: Rafters must be affixed where panels connect to each other.
Step 5:
Use the same method to assemble roof rafters (K) for the angled panels. The rafters (K) should be
affixed to the mounting bracket using the hole that will be furthest away from the corner of the
unit.
Note: Do not tighten the bolts right away as you may have to adjust the angle when inserting the PC
roof panels.

ZZZ-183.41215-32.1127-15.GP.EN.HER.doc HER-HP 6
Step 6:
Use nut (Hh) and washer (Gg) to affix the top cap (M) to the central hub (N).
Step 7:
First remove the protective layer from the PC roof panels, then insert them (Y, Aa, Ll, Qq) into the
roof rafters according to the below drawing instructions.
Note: the side that had the protective layer should be face down.
K
TOP VIEW

ZZZ-183.41215-32.1127-15.GP.EN.HER.doc HER-HP 7
Step 8:
After inserting the upper PC panels, insert the aluminum middle roof joints (O, P, Q, Pp) into the
roof rafters. The below drawing view is from inside the solarium looking up.
Note: the drain holes on the aluminum middle roof joints (O, P, Q, Pp) should be at the bottom.
Step 9:
After the installation on the middle roof joints complete, insert the bottom PC roof panels (Jj, Kk,
Mm, Rr) according to below drawing. They should overlap about two inches under the upper PC
roof panels and into the aluminum middle roof joints.
Before
After
Before
After
TOP VIEW

ZZZ-183.41215-32.1127-15.GP.EN.HER.doc HER-HP 8
Step 10:
Once the PC roof is complete, use aluminum edging ( S, U, W, Ss) to surround the edges of PC roof,
and using bolt (Bb) and roof joint (R), tighten securely.
Step 11:
Once the installation of the edging complete, start affixing the roof cross bars (T, V, X, Tt) using bolt (Ff).
Affix the top cross bars (Uu) onto the roof rafter (L) using bolt (Ff).

ZZZ-183.41215-32.1127-15.GP.EN.HER.doc HER-HP 9
Step 12:
Inside each of the panels (A, B), push two plastic plugs (Ii) into the ground, and then screw down
the panels using two screws (Ee) for each panels.
Special notes:
1. To remove windows (08-219), pull 1 pin out of the lock position and push the frame to the end
of the track, then ease the window out of the tracks one side at a time.
2. To remove screening panel, first remove windows, then unscrew the 2 screws at the top
corners of the screen frame.
3. Note that this unit is not waterproof. For best protection against rain, close the windows of
each frame with the outside window in the center, and the inside window at the top.
(2)
(1)

ZZZ-183.41215-32.1127-15.GP.EN.HER.doc HER-HP 10
12X15 Solarium
DESCRIPTION
QTY
DRAWING
DESCRIPTION
QTY
DRAWING
08-129-32
REGULAR
FRAME
A
10
08-130-32
FRAME NEXT TO
DOOR B
(with extra holes)
2
08-131-32
SLIDING DOOR
C
2
08-132-32
SLIDING DOOR
FRAME
D
2
08-133-32
CONNECTING
PIECE
E
12
08-136-32
TOP DOOR RAIL
F
2
08-137-32
BOTTOM
DOOR RAIL
G
2
08-138-32
PLASTIC
STOPPER
H
4
08-139-32
135° ANGLED
OUTSIDE
CONNECTOR
I
8
08-140-32
135° ANGLED
INSIDE
CONNECTOR
J
8
08-141-32
ROOF RAFTER
K
8
08-142-32
ROOF RAFTER
L
6
08-179-32
TOP CAP
M
1
08-178-32
CENTRAL HUB
N
1
08-145-32
MIDDLE
ROOF JOINT
O
4
08-146-32
MIDDLE ROOF
JOINT
P
4
08-147-32
MIDDLE ROOF
JOINT
Q
4
08-148-32
ROOF RAFTER
CAP
R
14

ZZZ-183.41215-32.1127-15.GP.EN.HER.doc HER-HP 11
DESCRIPTION
QTY
DRAWING
DESCRIPTION
QTY
DRAWING
08-149-32
EDGING
S
4
08-150-32
ROOF CROSS
BAR
T
4
08-151-32
EDGING
U
4
08-152-32
ROOF CROSS
BAR
V
4
08-153-32
EDGING
W
4
08-154-32
ROOF CROSS
BAR
X
4
08-155
(24 ¼”X42 ¼”)
TOP ROOF
LEFT PANEL
Y
4
08-156-32
SCREW
Z
28
08-157
(24 ½”x46 ½”)
TOP ROOF
CORNER
PANEL
Aa
4
08-158-32
BOLT
Bb
54
08-161-32
BOLT
Cc
12
08-165-32
RIGHT DOOR
LATCH
Dd-R
2
08-169-32
LEFT DOOR
LATCH
Dd-L
2
08-167-32
SCREW
Ee
24
08-168-32
BOLT
Ff
18
08-187
WASHER
Gg
39
08-189-32
ACORN NUT
Hh
3
08-193
PLASTIC PLUG
Ii
24

ZZZ-183.41215-32.1127-15.GP.EN.HER.doc HER-HP 12
DESCRIPTION
QTY
DRAWING
DESCRIPTION
QTY
DRAWING
08-195
(47”x47 ½”)
BOTTOM ROOF
CORNER PANEL
Jj
4
08-196
(46 ¼”x43”)
BOTTOM ROOF
LEFT PANEL
Kk
4
08-197
(24 ¼”x42 ½”)
TOP RIGHT
ROOF PANEL
Ll
4
08-198
(46 ¼”x43”)
BOTTOM ROOF
RIGHT PANEL
Mm
4
08-134-32
UPPER DOOR
RAIL END CAP
Nn
4
08-135-32
SCREW
Oo
4
08-170-32
MIDDLE ROOF
JOINT
Pp
2
08-172
(41 ¼”x42 ¼”)
TOP ROOF
CENTER PANEL
Qq
2
08-171
(41 ¼”x43”)
BOTTOM ROOF
CENTER PANEL
Rr
2
08-173-32
EDGING
Ss
2
08-174-32
ROOF CROSS
BAR
Tt
2
08-175-32
TOP ROOF
CROSS BAR
Uu
2
12-037-32
FEMALE BOLT
Cc-2
12
12-047-32
BOLT
Ww
12
(M5*15mm)

ZZZ-183.41215-32.1127-15.GP.EN.HER.doc HER-HP 13
AVAILABLE REPLACEMENT PARTS
DESCRIPTION
DRAWING
DESCRIPTION
DRAWING
08-219-32
PVC WINDOW
(in frame)
85-417-S
ROUND SPLINE
FOR SCREENING
10-493
PVC WINDOW
(replacement
material only)
11-572-32
BOTTOM PLASTIC
PANEL (for wall
panels)
85-417-P
ROUND SPLINE
FOR PVC
WINDOW
11-822-32
BOTTOM PLASTIC
PANEL (for doors)
15-123-32
PIN FOR PVC
WINDOW
15-097-32
DOOR WHEEL
ASSEMBLY
13-033
PC WINDOW (for
sliding door)
10-458
REPLACEMENT
WEATHERSTRIP
124”
12-046-32
MOSQUITO
SCREEN (in
frame)
15-124-32
MOUNTING
BRACKET FOR
RAFTER (K)
85-014
REPLACEMENT
SCREENING (no
frame)
15-125-32
MOUNTING
BRACKET FOR
RAFTER (L)

ZZZ-183.41215-32.1127-15.GP.EN.HER.doc HER-HP 14

ZZZ-183.41215-32.1127-15.GP.EN.HER.doc HER-HP 15
MAINTENANCE NOTES
1. In case of a defective or damaged part, or for any other questions concerning the
product, please contact the manufacturer directly.
2. Please have the parts list and part numbers on hand when ordering or requesting
replacement parts.
3. The product should not be installed adjacent to trees or a sloped roof. Snow and ice
may slide onto the roof and cause it to collapse.
4. While the product is designed for 4 seasons use, the roof must be kept free of
accumulation of snow.
ONE YEAR LIMITED WARRANTY
This product has been designed and manufactured to meet the highest standards of quality and
durability. Subject to the Conditions for Exercising the Warranty and the Limitations on the
Warranty set forth below, it is warranted to be free of material and manufacturing defects for a
period of one year from the date of purchase. Should the product become damaged, or the
warranty period has expired, please contact Gazebo Penguin Customer Service Department for
a complete schedule of replacement parts and prices.
CONDITIONS FOR EXERCISING THE WARRANTY
In order to properly exercise your warranty, please comply with the following:
Carefully inspect the contents of the carton for missing or damaged components.
Should you discover damaged or missing parts, do not return the product to the
place of purchase, but contact Gazebo Penguin Customer Service Department at the
numbers listed below:
Montreal: [phone] Elsewhere: 1-800-737-7174
NOTE: Damages/missing parts must be reported within 30 days of delivery.
LIMITATIONS ON THE WARRANTY
1. The product is not warranted against damages due to vandalism, abuse, falling or
thrown objects, or accumulation of snow.
2. The product is not warranted against damages due to extreme weather conditions,
such as thunderstorms, hail, strong wind or snow storms, or any other acts of God.
3. The product is only warranted in the event it is installed in accordance with the Gazebo
Penguin’s written instructions enclosed with the product.
4. The product is not warranted in the event it has been improperly anchored.
5. We reserve the right to replace or repair any defective product or parts at our discretion.