Gazebo penguin 43200-32 User manual

0
ZZZ-212.43200-32.1127-15.GP.EN.HER.doc HER-HP
43200-32
10’x10’ GAZEBO
ASSEMBLY INSTRUCTIONS
Two or more adults required for assembly
[e-mail]

1
ZZZ-212.43200-32.1127-15.GP.EN.HER.doc HER-HP
Before you assemble the Gazebo
It is important that this gazebo be anchored on a solid base with the provided screws.
Otherwise, please ensure that you use anchors sufficient for your surface.
The gazebo should not be installed adjacent to trees or a sloped roof. Snow and ice may
slide onto the gazebo and cause it to collapse.
Step 1:
Assemble beams “A” and “B” using center plate “F”, securing tightly with 8 bolts “Pp”. Lay out the
assembled beams in a rectangle and join at each corner with a corner plate “E”, again securing tightly
with 8 bolts “Pp”.
Step 2:
For each leg “G”, attach foot plate “H” using 3 bolts “Pp”.
A
A
B
B

2
ZZZ-212.43200-32.1127-15.GP.EN.HER.doc HER-HP
Step 3:
Have someone lift the beam assembly and attach each leg “G” into a corner, securing each using 4
bolts “Pp”. Repeat until all four legs are in place.
Step 4:
Install middle joint cover
“J” at each of the 4 beam
junctions, using 4 screws
“Qq” each.
Install corner cover “I” at
each of the corners,
using 4 screws “Qq”
each.

3
ZZZ-212.43200-32.1127-15.GP.EN.HER.doc HER-HP
Step 5:
Attach mounting brackets “O” and “P” to rafters “M” and “N” respectively. Use threaded hole about 8”
from end of rafter.
Lift central hub “L” to a height of about 110” (2.79m) at the center of the gazebo. (Caution: this part
may be heavy, use support as needed)
Attach one end of rafter “M” to the hub using 2 bolts “Pp”. Attach other end with mounting bracket to
the corner of the beam assembly with 2 bolts “Pp”. Use the set of holes closest to the inside. Repeat
with remaining “M” rafters.
Similarly, attach one end of rafter “N” to the hub using 2 bolts “Pp”. Attach other end with mounting
bracket to the beam assembly with 2 screws “Qq”. Use the set of holes closes to the inside. Repeat
with remaining “N” rafters.
Step 6:
Once all rafters are in place, install top
cap “K” over central hub “L”. Use flat
washers and acorn nuts “Vv” to secure
tightly.
Pp
Pp

4
ZZZ-212.43200-32.1127-15.GP.EN.HER.doc HER-HP
Step 7:
Install the flashings “Q” and “R” onto
the beam assembly, using screws
“Qq” on the inside. The notched end
of a flashing will always go in a
corner of the gazebo.
Step 8:
Install the curtain rails “T” on the inside of the beam assembly using bolts “Pp”.
Pp

5
ZZZ-212.43200-32.1127-15.GP.EN.HER.doc HER-HP
Step 9:
Slide the indicated polycarbonate
panels into the spaces between the
rafters, using the top groove of each
rafter. Ensure the side meant to face
the sun is on the outside. Use a
rubber hammer to carefully tap each
panel into the grooves.
Step 10:
Insert the middle roof joints in between the rafters and slide them up under the polycarbonate panels.
Tap lightly to ensure the panel is fully in the slot. Seen from above, most of the joint as well as the
drain holes should be beneath the roof panels.

6
ZZZ-212.43200-32.1127-15.GP.EN.HER.doc HER-HP
Step 11:
Slide the remaining polycarbonate roof panels in the lower groove of the rafters and into the lower slot
of the roof joints. Tap to make sure panels fit securely and do not extend past the ends of the rafters.
Step 12:
Starting from any end,
install all edgings, with
end caps “Gg” or “Hh” at
each junction or corner
respectively. Use bolts
“Pp” to secure.

7
ZZZ-212.43200-32.1127-15.GP.EN.HER.doc HER-HP
Step 13:
Install the upper
crossbars on the interior
of the roof using bolts
“Pp”, following the
shaped ends and letters.
Do not tighten bolts
immediately; install
loose and tighten once
all crossbars are in
place.
Repeat this step with the
lower crossbars.
Step 14:
a) Secure each foot plate into
the ground using screws “Rr”
and washers “Tt”.
b) Use lag shields (Ss) if
needed for harder surfaces.
Pp
Pp
Pp

8
ZZZ-212.43200-32.1127-15.GP.EN.HER.doc HER-HP
Step 15:
Install the screen curtains “Ww” in the interior groove of the curtain rails, using the provided hooks.
Install the privacy curtains “Xx” in the exterior groove of the rails. Once the hooks are in, use curtain
rail caps “Uu” to close ends of curtain rails.
Note that both curtains are packaged and
ordered in sets of 2 panels, each set
covering half the gazebo.
IMPORTANT NOTES:
Make sure all screws and bolts are tight.
If conditions are windy, you may have to add
cable guides at the corners.
Ww
Xx
Ww/Xx
Ww/Xx

9
ZZZ-212.43200-32.1127-15.GP.EN.HER.doc HER-HP
PART
QTY
DIAGRAM
PART
QTY
DIAGRAM
(11-624-32) 52 ¾”
TOP LEFT BEAM
A
4
(12-030-32)
RAFTER M
MOUNTING
BRACKET
O
4
(11-625-32) 52 ¾”
TOP RIGHT BEAM
B
4
(12-031-32)
RAFTER N
MOUNTING
BRACKET
P
4
(11-628-32)
CORNER PLATE
E
4
(11-638-32) 55 ¼”
RIGHT FLASHING
Q
4
(11-629-32)
CENTER PLATE
F
4
(11-639-32) 55 ¼”
LEFT FLASHING
R
4
(11-630-32) 81 ½”
LEG
G
4
(11-642-32) 47 ¾”
CURTAIN RAIL, 10’
SIDE
T
8
(11-631-32)
FOOT PLATE
H
4
(11-673) 30”x30”
LEFT UPPER ROOF
PANEL
V
4
(11-632-32)
CORNER COVER
I
4
(11-681) 30”x30”
RIGHT UPPER
ROOF PANEL
X
4
(11-633-32)
MIDDLE COVER
J
4
(11-646-32) 30 ¾”
LEFT MIDDLE ROOF
JOINT
Y
4
(13-034-32)
TOP CAP
K
1
(11-648-32) 30 ¾”
RIGHT MIDDLE
ROOF JOINT
Aa
4
(13-035-32)
CENTRAL HUB
L
1
(11-671) 33 1/4”x58 1/8”
LEFT LOWER ROOF
PANEL
Bb
4
(11-669-32) 83 5/8”
ROOF RAFTER
M
4
(11-672) 33 1/4”x58 1/8”
RIGHT LOWER
ROOF PANEL
Cc
4
(11-670-32) 61”
ROOF RAFTER
N
4
(11-651-32) 58 7/8”
LEFT EDGING
Dd
4

10
ZZZ-212.43200-32.1127-15.GP.EN.HER.doc HER-HP
PART
QTY
DIAGRAM
PART
QTY
DIAGRAM
(11-653-32) 58 7/8”
RIGHT EDGING
Ff
4
(08-167-32)
SCREW
Rr
12
(M6x100mm)
(11-654-32)
RAFTER CAP
Gg
4
(08-193)
PLASTIC PLUG
Ss
12
(11-655-32)
CORNER END
BRACKET
Hh
4
(08-187)
WASHER
Tt
13
(M6)
(11-656-32) 44”
LEFT LOWER
CROSSBAR
Ii
4
(11-697)
CURTAIN RAIL CAP
Uu
8
(11-658-32) 44”
RIGHT LOWER
CROSSBAR
Kk
4
(08-189-32)
ACORN NUT
Vv
1
(11-659-32) 17 ½”
LEFT UPPER
CROSSBAR
Ll
4
(13-036)
SCREEN CURTAIN
(set of 2 panels)
Ww
2
(11-661-32) 17 ½”
RIGHT UPPER
CROSSBAR
Nn
4
(13-037)
PRIVACY CURTAIN
(set of 2 panels)
Xx
2
(08-158-32)
BOLT
Pp
180
(M6x16mm)
(11-705)
CURTAIN HOOKS
80
(08-156-32)
SCREW
Qq
80
(M4x16mm)
10 mm KEY
1

11
ZZZ-212.43200-32.1127-15.GP.EN.HER.doc HER-HP

12
ZZZ-212.43200-32.1127-15.GP.EN.HER.doc HER-HP
MAINTENANCE NOTES
1. In case of a defective or damaged part, or for any other questions concerning the product, please
contact the manufacturer directly.
2. Please have the parts list and part numbers on hand when ordering or requesting replacement parts.
3. The product should not be installed adjacent to trees or a sloped roof. Snow and ice may slide onto the
roof and cause it to collapse.
4. While the product is designed for 4 seasons use, the roof must be kept free of accumulation of snow.
ONE YEAR LIMITED WARRANTY
This product has been designed and manufactured to meet the highest standards of quality and durability.
Subject to the Conditions for Exercising the Warranty and the Limitations on the Warranty set forth below, it is
warranted to be free of material and manufacturing defects for a period of one year from the date of purchase.
Should the product become damaged, or the warranty period has expired, please contact Gazebo Penguin
Customer Service Department for a complete schedule of replacement parts and prices.
CONDITIONS FOR EXERCISING THE WARRANTY
In order to properly exercise your warranty, please comply with the following:
Carefully inspect the contents of the carton for missing or damaged components. Should you discover
damaged or missing parts, do not return the product to the place of purchase, but contact Gazebo
Penguin Customer Service Department at the numbers listed below:
Montreal: [phone] Elsewhere: 1-800-737-7174
NOTE: Damages/missing parts must be reported within 30 days of delivery.
LIMITATIONS ON THE WARRANTY
1. The product is not warranted against damages due to vandalism, abuse, falling or thrown objects, or
accumulation of snow.
2. The product is not warranted against damages due to extreme weather conditions, such as
thunderstorms, hail, strong wind or snow storms, or any other acts of God.
3. The product is only warranted in the event it is installed in accordance with the Gazebo Penguin’s
written instructions enclosed with the product.
4. The product is not warranted in the event it has been improperly anchored.
5. We reserve the right to replace or repair any defective product or parts at our discretion.