Gemini 932MHW Use and care manual

Made in Italy Rev.00 - 01/18
UK
USER AND
INSTALLER MANUAL
INSTALLATION CERTIFICATE
The undersigned qualified installer attests to have personally fitted the here described vehicle
security system following the manufacturer instructions.
................................................
..........................................................................................................................
By :
Sold on :
Type of device :
Vehicle :
ALARM KIT
932MHW
&
Siren 725W
932MHW
&
SIREN 725W
GEMINI Technologies S.r.l.
Via Luigi Galvani 12 - 21020 Bodio Lomnago (VA) - Italia
Tel. [phone] - Fax [phone]
www.gemini-alarm.com
ISO 9001Certified Company

USER MANUAL
INSTALLER MANUAL
1.0
2.0 -
5.0
11.0
12.0
13.0
14.0
- OPERATING INSTRUCTIONS...................................................................................
1.1 - Complete system arming..........................................................................................
1.2 - System arming with sensors exclusion.....................................................................
1.3 - Passive arming.........................................................................................................
1.4 - Arming delay.............................................................................................................
1.5 - System armed..........................................................................................................
1.6 - Alarm, inhibit time between alarms and alarm cycles...............................................
1.7 - System disarming.....................................................................................................
1.8 - Alarm memory...........................................................................................................
GEMINI REMOTE CONTROL 738W AND BATTERY REPLACEMENT....................
...........................................................................................
- PINOUT TABLES........................................................................................................
4.1 - 20-pin connector........................................................................................................
4.2 - 8-pin connector..........................................................................................................
- WIRING DIAGRAM.....................................................................................................
....................................
..........................................................................................
.........................................................
7.3 - Passive arming.........................................................................................................
7.4 - Door switch polarity selection...................................................................................
7.5 - Double pulse unlock.................................................................................................
...............................................
....................................................
.......................................................................
..................................................................................
...............................................................
- DELETING PROGRAMMED DEVICES...................................................................
- SYSTEM RESET......................................................................................................
- TECHNICAL SPECIFICATIONS...............................................................................
- WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT DIRECTIVE (WEEE).....
3.0
4.0
6.0
7.0
8.0
9.0
10.0
- WIRELESS SIREN 725W
- VEHICLE CODE PROGRAMMING............................................................................
- SYSTEM PROGRAMMING....................................................
7.1 - Optical signals................
7.2 - Audio signals...................................................
- SYSTEM PROGRAMMING EXAMPLE.......................
- ULTRASONIC VOLUMETRIC PROTECTION........
9.1 - Connections and positioning.............
9.2 - Sensor adjustment..................
- LEARNING NEW DEVICES......................
PAGE 02
Dear customer, thank you for choosing this GEMINI product manufactured in Italy specifically for
recreational vehicles.
Please read the present manual carefully to familiarize yourself fully with the operation of your alarm
system and do keep it for future reference.
PAGE 03
UK TABLE OF CONTENTS
For the installer.
This sign indicates that the system will operate according to the selected connections
and programming or it simply provides useful setup instructions.
!
For the user.
This sign highlights useful information.
PAGE 03
PAGE 03
PAGE 03
PAGE 04
PAGE 04
PAGE 04
PAGE 04
PAGE 04
PAGE 04
PAGE 05
PAGE 06
PAGE 06
PAGE 06
PAGE 10
PAGE 11
PAGE 12
PAGE 12
PAGE 13
PAGE 13
PAGE 03
PAGE 07
PAGE 08
PAGE 09
PAGE 09
PAGE 09
PAGE 09
PAGE 09
PAGE 09
PAGE 09
PAGE 10
PAGE 10
The following signs are used throughout the manual to emphasize important instructions or special information:
USER MANUAL
1.0 - OPERATING INSTRUCTIONS
1.1 - COMPLETE SYSTEM ARMING
1.2 - SYSTEM ARMING WITH SENSORS EXCLUSION
Press the lock button on the vehicle remote control or button
system arming is confirmed by a siren chirp and a flash of the turn indicators (if optical/acoustic signals
are enabled). The system has a 30 sec. arming delay during which the LED is ON steady.
To arm the system without arming interior protection press button “3” on the Gemini remote control.
“1” on the Gemini 738W remote control;
System arming is confirmed by a siren chirp and a flash of the turn indicators (if signals are enabled).
1.3 - PASSIVE ARMING
If programmed for passive arming, the system will automatically arm approximately 60 sec. after
ignition is switched OFF and the last door is opened and closed. Arming is confirmed by a siren chirp
and a flash of the turn indicators (if signals are enabled).
If programmed for passive arming, interior protection is excluded.
Opening a door during the 60-second passive arming countdown will cause the
procedure to interrupt; it will resume once the door is closed.
Exclusion of sensors is bound to each single arming cycle. They will be reset upon next
arming.
• FIAT DUCATO ‘11
• FORD TRANSIT ‘14
• RENAULT MASTER ‘10
›
›
›
Sensors can be excluded via the vehicle original remote control on the following vehicles:
To exclude the sensors via the vehicle original remote control, proceed as follows:
• Lock the vehicle via the vehicle original remote control.
• Wait at least 5 sec., and press the lock button again.
• Exclusion is confirmed by 1 low-pitched chirp.
THIS CONFIRMATION TONE CANNOT BE EXCLUDED.
but before the end of the arming delay,
NB:

1.4 - ARMING DELAY
There is a 30 sec. delay from the time the system is armed to allow you to leave the vehicle without
triggering an alarm: it will be signaled by the LED turned ON steady.
PAGE 04 PAGE 05
If an alarm event has occurred while you were away from your vehicle, it will be signaled, when you
disarm the sytem, by 5 siren chirps and 5 flashes of the turn indicators. Alarm causes and relative LED
signals are listed in the next paragraph.
3.8 - ALARM MEMORY
The LED memory allows to identify the last alarm event signaled by 5 siren chirps and 5 turn indicator
flashes when the system is disarmed.
Turn ignition key “ON” and count the number of flashes. The status LED will flash according to the last
alarm detected prior to disarming (see table below).
The flash sequence is repeated 3 times; to interrupt turn ignition key “OFF”.
The table below lists the various alarm causes and relative number of LED flashes.
LED FLASHES ALARM CAUSES ALARM
CYCLES
10
10
1
1
0
10
0
10
10
10
Ignition attempt (+15/54)
Boot tamper
Volumetric or external sensor
Wireless magnetic contacts or
opening detectors
Wireless infrared sensors (PIR)
Wire tampering
Door tamper
Bonnet tamper
LED ON (1 second)LED OFF (2 seconds)
1.6 - ALARM, NEUTRAL TIME BETWEEN ALARMS AND ALARM CYCLES
Alarm events are signaled by optical/acoustic signals
Each alarm event can generate up to 10 cycles for
each input and for each arming cycle. One alarm cycle lasts for 30 sec.
. Once the alarm ceases, there is a 5 sec. time-
interval before another alarm can be triggered.
1.5 - SYSTEM ARMED
After the arming delay the system is fully armed and ready to detect any alarm event. The LED will start
flashing to confirm the armed status.
1.7 - SYSTEM DISARMING
Press the unlock button on the vehicle original remote control or button
flashes of the turn indicators (if signals
are enabled).
“2” on the Gemini 738W
remote; system disarming is confirmed by 2 siren chirps and 2
INSTALLER MANUAL
The wireless waterproof digital siren with back-up battery has a transceiver which operates at a
frequency of approx. 2.45 GHz. The 3-wire siren, which also manages the bonnet switch, connects
directly to the vehicle battery with no wires to be routed from the engine compartment (siren and
bonnet switch) to the control unit inside the cabin. Use the supplied metal bracket and screws to mount
the siren to a suitable metal surface in the engine bay, away from heat sources and moving parts.
• The L-bracket can be attached on the long or short side (Fig.1).
• Face the siren speaker downward so as to avoid water damage (Fig.2).
Drill a hole using a
3mm drill bit.
Fig.1
3.0 - WIRELESS SIREN 725W
2.0 - GEMINI REMOTE CONTROL 738W AND BATTERY REPLACEMENT
If the right connections have been made, the vehicle doors will lock/unlock when pressing
the arming/disarming buttons.
1234
1234
YES
NO
CORRECT installation examples
INCORRECT installation examples
1
2
34
1
2
3
4
123
4
1
2
3
4
Fig.2
BUTTON 1:
TOTAL SYSTEM ARMING
(and door lock)
BUTTON 3:
PARTIAL ARMING
(door lock + sensor exclusion)
BUTTON 2
SYSTEM DISARMING
(and door unlock)
:
If the LED blinks 3 times at the press of a button, the battery is weak and must be replaced as follows:
ON OFF
4
4
1
12
23
3
Use only 23AE batteries.
Risk of explosion if battery is replaced by an incorrect type.
Discard used batteries properly in special dedicated containers.
ATTENTION:
!

4.0 - PINOUT TABLES
-1-
-2-
-3-
-4-
-5-
-6-
-7-
-8-
-9-
-10-
-11-
-12-
-13-
-14-
-15-
-16-
-17-
-18-
-19-
-20-
-----
-----
-----
-----
GREEN-BROWN
GREEN
BROWN
BLACK
RED
BLACK marked “G”
LIGHT BLUE-GREY
LIGHT BLUE
PINK
GREEN-BLACK
GREEN
BLUE
WHITE-BLACK
YELLOW-BLACK
-----
-----
WIRE FUNCTIONPOSITION WIRE COLOUR
15A
+
12 V
Battery
8A
MAX !
BLACK marked “M”
GROUND
POSITIVE
BLACK marked “R”
ORANGE**
ORANGE**
Output - turn indicators
BLACK marked “G”
+30
Ignition
BLACK marked “H”
BLACK marked “H”
Engine immobilizer
5.0 - WIRING DIAGRAM
Before carrying out
electrical connections,
disconnect the negative
battery terminal and re-
connect again after
completion.
!
20-PIN CONNECTOR
-----
-----
-----
-----
Positive/negative input - door switches
DO NOT CONNECT
DO NOT CONNECT
LED negative output
LED positive output
Ignition
CAN BUS (CAN-H) signal
CAN BUS (CAN-L) signal
Positive output - system armed (+A)
Negative input - external sensors
Negative input - bonnet switch (for pairing purposes)
Optical pulse signals (Hazard)
Lock command (1.5 sec.* negative pulse when pressing
remote control button “1” or “3”)
Unlock command (1.5 sec.* negative pulse when
pressing remote control button “2”)
-----
-----
Negative input - external sensors
Positive/negative input - door switches
GREEN-BLACK
GREEN-BROWN
CAN BUS signal
LIGHT BLUE-GREY (CAN-H)
PAGE 06 PAGE 07
LIGHT BLUE (CAN-L)
Lock command (negative)
Unlock command (negative)
WHITE-BLACK
YELLOW-BLACK
Positive output - system armed (+A)
PINK
Ground
Siren output
Positive supply
Positive output - turn indicators
Engine immobilization
Siren output
Engine immobilization
Positive output - turn indicators
-1-
-2-
-3-
-4-
-5-
-6-
-7-
-8-
BLACK marked “M”
-----
BLACK marked “R”
ORANGE
BLACK marked “H”
-----
BLACK marked “H”
ORANGE
WIRE FUNCTIONPOSITION WIRE COLOUR
8-PIN CONNECTOR
BLUE*
HAZARD
(optical pulse signals)
In this case, DO NOT connect
the alarm ORANGE wires to
the turn indicators.
For complete information regarding connections, please refer to your vehicle wiring
diagram.
(See available diagrams in the restricted area of our website: www.gemini-alam.com).
*If “ feature is enabled (par. 8.0), lock/unlock pulse time will be 0.5 sec.
instead of 1.5 sec.
Double pulse unlock”
Turn indicators connections: Select ONLY one of the following connections :
BLUE wire
ORANGE wires
:ONLY
.
:
Optical signals activated by connection to the Hazard switch will turn ON during an alarm
condition
turn indicator flashes for all optical signaling functions (factory enabled).
*
**
!
BLACK
(RED taped end)
5A
We recommend
adding
a 5A fuse
Bonnet switch
WIRELESS SIREN
725W
BLACK
(-)
BLACK
(+)
GREEN
Bonnet switch
(Ground to pair devices)
Red
Black
Brown
Green
Do not connect
STATUS LED
Button function not applicable
for this product version.

PAGE 08 PAGE 09
6.0
help you understand the coding procedure, here below is an example illustrating the configuration
procedure. In this case the code to be entered is 1-0-3.
- VEHICLE CODE PROGRAMMING
The system must be configured according to the specific vehicle model on which it is to be installed.
To
Press the vehicle remote control lock/unlock buttons to make sure the alarm system works properly.
If needed, disconnect the 8-pin connector and reconnect it after a few seconds.
A separate leaflet, included in the alarm packaging, lists all the available vehicles (codes
are updated at packaging time).
Up-to-date information on supported vehicle models can be found in the restricted area
of our website: .www.gemini-alarm.com
The alarm has an indicator LED that signals any wrong vehicle code inserted.
The code must range between 100 and 235 otherwise the LED on the unit blinks
repeatedly and the procedure is interrupted.
The previously inserted code remains stored.
The procedure is also invalidated if the LED blinks more than 10 times. In this case
there is no optical warning, the procedure is simply interrupted.
In either case, repeat the whole procedure.
!
!
Connect the wiring harness connectors to the corresponding alarm connectors.
Press and hold the button shown below until the LED lights up.
The LED will start flashing after 3 to 4 seconds; count the flashes.
In this case press the button at the 1st flash which corresponds to number “1”.
After 4 seconds, the LED will flash for the second time.
Press the button at the 10th flash which corresponds to number “0”.
After 4 more seconds, the LED will flash for the third and last time.
Press the button at the 3rd flash which corresponds to number “3”.
Release the button, the LED
will switch OFF.
Press
Press
Press
1st FLASH
10th FLASH
3rd FLASH
3-4 seconds
When the last digit is entered, the alarm system “repeats” the entered code:
• 1 FLASH +
• 10 FLASHES +
• 3 FLASHES
A SHORT PAUSE
A SHORT PAUSE
7.1
.
- OPTICAL SIGNALS
This function activates the optical signals (turn indicator flashes) that confirm system
arming/disarming
If the vehicle already has optical lock/unlock signals, the turn indicators alarm flashes
should be disabled.
7.2
7.3
7.4 -
.
Opening a door during the 60-second passive arming countdown
by the
- ACOUSTIC SIGNALS
- PASSIVE ARMING
DOOR SWITCH POLARITY SELECTION
This function activates the acoustic signals (siren chirps) that confirm system arming/disarming
This function arms the system 60 sec. after ignition is switched OFF and the last door is opened and
closed. will cause the procedure to
interrupt; it will resume once the door is closed
This function modifies the alarm input signal (positive or negative) according to the signal generated
door switch.
.
!
DOUBLE PULSE UNLOCK QUICK ACTIVATION:
NB:
- Disconnect the alarm system power supply and ground the Green/Black wire.
- Connect the alarm power supply; 3 quick high-pitched chirps will confirm operation.
- Remove the Green/Black wire from ground.
To reset the default setting, repeat the above steps; 1 low-pitched chirp will confirm the operation.
7.5 - D
If this feature is enabled, 2 unlocking pulses will be supplied to unlock all doors at the same time.
This is useful in case separate actions are required to open the driver door and then the other doors.
OUBLE PULSE UNLOCK
7.0 - SYSTEM PROGRAMMING
The table below applies to the system programmed in “standard configuration”.
Every time you enter in programming mode, the alarm system resets to the default settings.
SELECTABLE FUNCTIONS STATUS LED FLASHES
Enabled
Disabled
Disabled
Enabled
Disabled
Arming/disarming optical signals
Arming/disarming acoustic signals
System passive arming
Door input - positive
Double pulse unlock
S
Alack of power during electrical system maintenance, will not affect the programming.
8.0 - SYSTEM PROGRAMMING EXAMPLE
To enter in programming mode proceed as follows:
• With the alarm system disarmed, turn ignition key “ON”.
• Wait approx. 2 sec. for the LED to light up.
• While the LED is ON, press remote control button “ON”.
Press Gemini remote control button “ ” to enable programmable functions and button
“ ” to disable them.
ON
OFF

PAGE 10 PAGE 11
In both cases, the system will move on to the next function.
Repeat the above steps to enable or disable the other functions.
When the last function is programmed, in addition to the confirmation tone, to
the system gives 2 low-pitched chirps, 1 high-pitched chirp and
indicate the end of
the programming procedure, the
turn indicators flash twice.
A quick a low pitched chirp and 2 flashes of the turn indicators will confirm the
system is in programming mode.
high-pitched chirp, long
Beep
Boop
To the functions press once the
.
A quick high-pitched chirp will confirm operation.
The LED will flash according to the selected
function (from 1 to ).
enable “ON”
BUTTON
5
OR
To the functions press once the
.
A long low-pitched chirp will confirm operation.
The LED will flash according to the selected
function (from 1 to ).
disable “OFF”
BUTTON
5
ON OFF
9.0
9.1
13.2
cells
To check the sensitivity level proceed as follows
• With the alarm system disarmed, roll down the front window approx. 20 cm.
• Close all doors, bonnet and boot and arm the system.
• During the arming delay introduce an object in the cabin through the window and move it around;
the status LED will turn off to
• I is too high or too low, readjust the trimmer and repeat the above procedure
- ULTRASONIC VOLUMETRIC PROTECTION
- CONNECTIONS AND POSITIONING
- SENSOR ADJUSTMENT
Insert the WHITE connector in the “W” marked socket.
Insert the RED connector in the “R” marked socket.
Install the ultrasonic sensor on the top part of the windshield internal pillars, away from the air
vents and point them towards the center of the rear window.
sensor :
• Set the trimmer to an intermediate position (medium sensitivity).
signal a presence.
f the sensitivity level .
ULTRASONIC
CELLS
CONNECTIONS
SENSITIVITY
ADJUSTMENT
To carry out the operation successfully, make sure the required electrical connections
(bonnet switch and ignition) are properly connected.
If there is no bonnet switch, ground the GREEN wire (20-pin connector, pos. 15).
To activate the code-learning mode proceed as follows:
• With the system disarmed, open the vehicle bonnet and keep it opened or ground the GREEN wire.
• Cycle ignition key - - - .
At the 4th cycle leave ignition
• A siren chirp and will confirm the system is in learn mode. The LED
will turn ON steady.
“”“”“”“”ON-OFF ON-OFF ON-OFF ON
• key “ON”.
2 flashes of the turn indicators
The “ON-OFF” cycles must be carried out within 4 sec. otherwise the procedure is
invalidated.
Do not close the bonnet otherwise all previously programmed devices will be erased as
described in the next paragraph.
10.0 - LEARNING NEW DEVICES
Storing memory is for 60 devices.
If an extra device is added, it automatically deletes the first device stored in memory.
!
!
!
!
The system is ready to receive the device codes.
Depending on which device is to be paired:
• Press twice one of the buttons on the remote control;
• Make the magnetic contact transmit twice (bring contact and magnet together and then move apart);
• Press the opening detector button twice;
•D
1.
2.
isconnect and reconnect the siren connector.
The LED will switch OFF for approx.1 sec. to confirm the device has been learned.
Repeat this same procedure to learn other devices.
Turn ignition key “OFF”.
Two low-pitched chirps and a flash of the turn indicators will confirm the end of the procedure.
The status LED will turn OFF.
Close the bonnet or remove the GREEN wire from ground (bonnet switch).
3.
4.
5.
6.

PAGE 12 PAGE 13
All devices previously programmed can be deleted. To clear memory proceed as follows:
• With the system disarmed, open the vehicle bonnet and keep it opened or ground the GREEN wire.
11.0 - DELETING PROGRAMMED DEVICES
To carry out the operation successfully, make sure the required electrical connections
(bonnet switch and ignition) are properly connected.
If there is no bonnet switch, ground the GREEN wire (20-pin connector, pos. 15).
!
• Cycle ignition key - - - .
•At the 4th cycle, leave ignition key “ON”.
• A siren chirp and will confirm the system is in delete mode.The LED
will turn ON steady.
• Close the bonnet or remove the GREEN wire from ground (bonnet switch).
• Leave the bonnet closed for at least 8 seconds to clear the memory.
“”“”“”“”ON-OFF ON-OFF ON-OFF ON
2 flashes of the turn indicators
The “ON-OFF” cycles must be carried out within 4 sec. otherwise the procedure is
invalidated.
If the bonnet is opened before 8 seconds, the devices will not be
deleted.
• The LED will switch OFF when the devices have been deleted.
• Turn ignition key “OFF”.
•Aflash of the turn indicators will confirm the end of the clearing procedure.
!
!
To reset the system proceed as follows:
• Disconnect the system.
• Short-circuit the RED and BLACK wires of the 2-pin LED connector.
• Connect the system; once the alarm system is powered, 4 acoustic signals will sound and the turn
indicators will flash 4 times.
• Remove the previously created short-circuit; the status LED will light up steady.
• Turn ignition key “ON”; reset is confirmed by the wailing of the siren for approx. 3 seconds.
• Turn ignition key “OFF”. The LED turns OFF and there are no acoustic signals.
By activating the following procedure, the system returns to the state.
This procedure must therefore only be used in case of need, before programming the
system or auto-learning the turn indicator flashes.
factory default
!
12.0 - SYSTEM RESET
13.0 - TECHNICAL SPECIFICATIONS
14.0 - WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT DIRECTIVE (WEEE)
The present device does not fall within the scope of Directive 2002/96EC on Waste Electrical and
Electronic Equipment (WEEE) as specified in art. 2.1 of L. D. No. 151 of 25/07/2005.
932MHW UNIT :
Power supply
Engine immobilizer relay contact capacity
Current draw (system armed + LED flashing)
Operating temperature range
Turn indicators relay contact capacity
Alarm cycle duration
Maximum positive current output when armed (+A)
12Vdc
15mA
-30°C => +70°C
8A @ 20°C
30 sec.
@ 12Vdc
8A @ 20°C
700mA
SIREN 725W:
Power supply
Operating temperature range
Current draw (when triggered)
Current draw (in standby)
Maximum siren output
10-15Vdc
-35°C => +80°C
1.5A @12Vdc
2.5mA @12Vdc
108dB @ 1m