Gemini 932 Series User manual

Made in Italy AVS: Rev 08/16
UK
USER MANUAL
932

PAGE 2
TABLE OF CONTENTS
UK
1.0
2.0
4.0
- PRELIMINARY ADVICE.............................................................................................
- OPERATING DESCRIPTION.....................................................................................
2.1-Complete system arming..........................................................................................
2.2-System arming with sensor and comfort control exclusion.......................................
2.3-Passive arming.........................................................................................................
2.4 - Arming delay.............................................................................................................
2.5-System armed..........................................................................................................
2.6 - Alarm, neutral time between alarms and alarm cycles.............................................
2.7-System disarming.....................................................................................................
2.8-Emergency disarming by electronic key...................................................................
2.9 - Alarm memory...........................................................................................................
...................................SNOITIDNOCYTNARRAW
- WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE) DIRECTIVE.......
USER MANUAL
INSTALLER MANUAL
3.0 .....................................................-
1.0-PRELIMINARY ADVICE
Dear Customer, th
.
same as 933 without self-powered battery.
:
GEMINI 932:
e present manual illustrates the most fully featured alarm system; not all functions,
electrical connections etc. will therefore apply to all models.
Before installing, identify your alarm model and refer to it for the correct instructions
The following signs, intended for the installer or the user, indicate particular functions or connections
as follows
For the user.
This sign highlights useful information.
2.0-OPERATING DESCRIPTION
Exclusion of sensors and comfort feature is only bound to each single arming
cycle.
USER MANUAL
2.1 - COMPLETE SYSTEM ARMING
2.2-SYSTEM ARMING WITH SENSOR AND COMFORT FEATURE EXCLUSION
Press the lock button on the
).
.
.
.
vehicle original remote control; system arming is confirmed byasiren
chirp (if feature has been enabled) and a flash of the turn indicators.
The system hasa30” arming delay (indicated by the LED turned ON steady
Whenthesystemisarmed,theinternalvolumetricprotectionandcomfort featurecanbeexcluded as follows:
Show the electronic key to its receptacle; the LED will give outaquick flash
Close all vehicle doors and press the lock button on the original remote control
System arming is confirmed by the standard optical/acoustic signals
Disarm the system and turn ignition key “OFF”.

PAGE 3
2.3 - PA
When this function is programmed, the system passively arms approx. 60” after ignition switch OFF
and after the last door is opened and closed.
System activation is confirmed by the standard optical/acoustic signals.
SSIVE ARMING
If passive arming is enabled, the internal sensors and the comfort output (automatic
window roll-up) are excluded.
Opening a door 60” before the system is armed causes the procedure to interrupt; it is
resumed once the door is closed.
2.4 - ARMING DELAY
The arming delay lasts approximately 30” and is signalled by the LED turned ON steady;
.
it is possible
to exit the vehicle without triggering any alarm
2.5-SYSTEM ARMED
2.6 - ALARM, NEUTRAL TIME BETWEEN ALARMS AND ALARM CYCLES
2.7-SYSTEM DISARMING
2.8 - EMERGENCY DISARMING BY ELECTRONIC KEY
After the arming delay, the system is fully armed and ready to detect any alarm condition. When the
system is fully armed, the LED will start flashing.
An alarmcondition is signalled
beforeanotheralarmcyclestarts,there is a
.
Press the unlock button on the vehicle original remote control.
nrutehtfosehsalf2dnasprihcneris2ybdemrifnocsignimrasiD
indicators.
signals are detailed in .
This disarming
by optical/signals.
.“5.xorppafo”emitlartuen“tub,dereggirtsimralaehtretfA
An alarm event generates a maximum of ten alarm cycles for each input and for each arming cycle
(if feature has been enabled)
An alarm condition is signalled by5acoustic signals (if feature has been enabled) and 5 flashes of the
turn indicators.
The various alarm causes and relative LED
mode is used for “EMERGENCY DISARMING” and “TOTAL DISARMING”.
Touching the electronic key to its receptable disarms and switches off the system which does not
rearm when the remote control is used.
acoustic
30”
paragraph (2.9)
To restore normal operation, touch the electronic key to its receptacle.
A quick chirp andaflash of the status LED will confirm that the system is back to normal
mode.

PAGE 4
2.9 - ALARM MEMORY
chirps 5 times (
), it means that an alarm conditon has occured while away from your vehicle
If, when disarming, the turn indicators flash 5 times and the if feature has been
enabled .
The cause that triggered the alarm can be identified by the LED memory.
Turn ignition key “ON”;the vehicle status LED will blink according to the last alarm detected.
Optical signals are repeated 3 times; to interrupt, turn ignition key “OFF”.
The table below lists the various alarm causes and relative LED signals.
siren
last
SESUACMRALASEHSALFDEL ALARM
CYCLES
10
10
1
10
10
0
10
Ignition attempt (+15/54)
Door opening
Bonnet opening
Boot opening
Volumetric or external sensor
Wire tampering
LED ON (1 second)LED OFF (2 seconds)
3.0-WARRANTY CONDITIONS
This product is guaranteed to be free from manufacturing defects foraperiod of 24 months from the
installation date shown on this warranty, in compliance with the Directive 1999/44/CE.
Please fill-in entirely the guarantee certificate included in this booklet and do NOT REMOVE the
guarantee label from the device.
The warranty will become void if labels are missing or torn, if the installation certificate is not fully
compiled or if the enclosed sale document is missing.
The guarantee is valid exclusively at authorized Gemini Technologies S.p.A. Service Centers.
The manufacturer declines any responsibility for eventual malfunctions of the device or any damage
to the vehicle electrical system due to improper installation, use or tampering.
This alarm system is solely intended to be a theft-deterrent device.
4.0-WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT
(WEEE) DIRECTIVE
The present device does not fall within the scope of Directive 2002/96/EC on Waste Electrical and
Electronic Equipment (WEEE) as specified in art. 2.1 of L.D. no. 151 of 25/07/2005.
TECHNICAL SPECIFICATIONS
Power supply
Current absorption @ 12Vdc with system armed and LED flashing
Working temperature
Turn indicators relay contact capacity
Engine immobiliser relay contact capacity
Alarm cycle duration
Maximum positive current output when armed (+A)
Maximum load of siren output
range
12 Vdc
15 mA
-30°C to +70°C
8A@ 20°C
8A@ 20°C
30 sec.
700 mA
1 A

GEMINI Technologies S.p.A.
Via Luigi Galvani 12-21020 Bodio Lomnago (VA)-Italia
Tel. [phone]-Fax [phone]
www.gemini-alarm.com
ISO 90001 Certified Company Reg. n.532-A
UNI EN ISO 9001:2008
Aermarket Vehicle Soluons Limited
7 Dudley Court , Jessop Close, Clacton-on-Sea, Essex, CO15 4LY
TEL: [phone]
Email: [email protected] | Web: www.avsgemini.com
UK Distributors of the Gemini Alarm Systems
AVS reserve the right to effect changes to the product without further noce. E&OE