Gemini 839 Series User manual

Made in Italy AVS: Rev 08/16
UK
USER MANUAL
839

PAGE 2
1.0
2.0
3.0
- PRELIMINARY ADVICE.............................................................................................
- OPERATING DESCRIPTION.....................................................................................
2.1-Vehicle CDL locking.................................................................................................
2.2-Vehicle CDL locking and comfort control.................................................................
2.3-Vehicle CDL unlocking..............................................................................................
- REMOTE CONTROL BATTERIES REPLACEMENT..................................................
USER MANUAL
1.0 - PRELIMINARY ADVICE
Dear Customer,
:
the following warning signs in the present manual provide important notices to the installer and the
user for installing and using this product correctly
Indications useful for the user.
This icon provides the user with indications for a diversificated use of the system or it
simply provides indications useful for the use.
TABLE OF CONTENTS
UK
2.0-OPERATING DESCRIPTION
USER MANUAL
2.1 - VEHICLE CDL LOCKING
2.2 - VEHICLE CDL LOCKING AND COMFORT CONTROL
2.3 - VEHICLE CDL UNLOCKING
Press the button on the remote control;
.
.
Press the button on the remote control;
..
the LED will light up steady for 10” and the turn indicators will
blink twice to confirm that the vehicle has been locked .
After this lapse of time, the LED will start blinking until the system is disarmed
If the comfort feature is activated, the vehicle doors will lock and the windows will roll up.
In this case the LED will light up steady during the comfort locking and stay lit for 10” afterwards.
If the remote has two buttons, the comfort feature can be excluded by pressing first the dotted button
(lock) and then the smooth button (comfort exclusion)
the turn indicators will blink three times to confirm that the
vehicle has been unlocked
ThismanualalsoreferstotheLEDandtoitsvariousopticalsignals.
TheLEDisoptionalandthereforenotincluded in thekit.

PAGE 3
To prevent problems with the remote control, it has been provided withadevice that will signal the
charge condition of the batteries inside.
During normal use of the remote control, when you pressacommand button the green LED will light
up withasteady light.
If the batteri
.
For battery replacement follow the indications reported below
es are too weak for normal operation of the remote control, when the button is pressed the
green LED will start blinking, advising you that it is time to replace the batteries
3.0-REMOTE CONTROL BATTERIES REPLACEMENT
.
Separate the
plastic shells of
the remote
control, paying
attention to not
damage the
internal circuit. Remove the discharged
batteries and insert the new
batteries in their housing, taking
care not to invert the polarity.
Close the
plastic shells
of the remote
and verify the
remote control
works
properly.
BATTERIES
Use only batteries of Cr1616 type.
Discard used batteries properly in special dedicated containers.
WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT
(WEEE) DIRECTIVE
In the European Union, this lable indicates that this product must not be disposed of with household
waste. It should be deposited at an appropriate facility to enable recovery and recycling (directive
2002/95/CE, 2002/96/CE and 2003/108/CE).
For information on how to recycle this product responsibly in your Country, please visit the web-site:
Www.eur-lex.europa.eu
WARRANTY CONDITIONS
etadnoitallatsniehtmorfshtnom42sihT
shown on this warranty coupon, taking into consideration the 1999/44/CE.
Therefore, you are kindly requested to fill entirely the guarantee certificate included in this booklet and
to NOT REMOVE the guarantee label from the device.
product is guaranteed to be free from manufacturing defects
The warranty will become void if labels are missing or torn, if the installation certificate is not fully
compiled or if the enclosed sale document is missing.
The guarantee is valid exclusively at authorized Gemini Technologies S.p.A. Service Centers.
The manufacturer declines any responsibility for eventual malfunctions of the device or any damage
to the vehicle electrical system due to improper installation, use or tampering.

GEMINI Technologies S.p.A.
Via Luigi Galvani 12-21020 Bodio Lomnago (VA)-Italia
Tel. [phone]-Fax [phone]
www.gemini-alarm.com
ISO 90001 Certified Company Reg. n.532-A
UNI EN ISO 9001:2008
Aermarket Vehicle Soluons Limited
7 Dudley Court , Jessop Close, Clacton-on-Sea, Essex, CO15 4LY
TEL: [phone]
Email: [email protected] | Web: www.avsgemini.com
UK Distributors of the Gemini Alarm Systems
AVS reserve the right to effect changes to the product without further noce. E&OE
12.0-TECHNICAL SPECIFICATIONS
Power supply 839
Current absorption @ 12Vdc with system armed and LED flashing
Working temperature range
Turn signals relay contact capacity
Maximum positive current output when armed (+A)
12/24 Vdc
15 mA
From -30°C to +70°C
8Aat 20°C
700 mA