Geutebruck G-Cam/EBC-5101 User manual

IMPORTANT: We recommend operating IP cameras only in isolated networks or behind suitable
firewalls.
This Quick Start Guide describes how to quickly install and connect the G-Cam/EBC-5101 Box IP Camera. For
more information, please refer to the IP Camera Installation/User Guide. shop.geutebrueck.com
Installation Notices
•The camera must be installed by qualified persons. The installation should comply with local regulations.
•Do not replace the batteries of the camera independently. There is a risk of explosion if the battery is replaced
with an incorrect type. Used batteries must be disposed of according to local regulations.
•If you want to use an external power source, ask the camera manufacturer for a suitable device.
Camera’s Connectors
NOTE: It is not recommended to record with the microSD card for 24/7 continuously, as it may not be able to
support long term continuous data read/write. Please contact the manufacturer of the microSD card for
information regarding the reliability and the life expectancy.
Mounting C/CS Mount Lens
Follow the instructions below to mount the C/CS Mount Lens to the camera.
• Remove the plastic cover from the camera.
• Remove the dustproof protective film from the CMOS image sensor.
•For C Mount Lens, mount the C/CS Mount Adapter to the camera first.
•Attach the lens to the adapter.
Camera Cabling
Please follow the instructions below for cable connections.
Power Connection
Use a DC 12V / AC 24V power adaptor and plug it to the power connector of the camera and the power outlet.
Alternatively, users can use an Ethernet cable and connect it to the RJ-45 connector of the camera and a Power
Sourcing Equipment (PSE) switch.
NOTE: If the device is powered over Ethernet, make sure the PSE is connected to the network.
Connect one end of the Ethernet cable to the RJ-45 connector of the camera and plug the other end of the cable to
the network switch or PC.
NOTE: In some cases, Ethernet crossover cable might be needed when connecting the camera
directly to the PC.
NOTE: Check the status of the link indicator and activity indicator LEDs. If the LEDs are unlit, please check
the LAN connection.
Green Link Light indicates good network connection.
Orange Activity Light flashes for network activity indication.
Initial login to the IP camera
The first time you access the IP camera, you will be prompted to change your password. You must perform this
step to continue.
For more information, refer to the user manual of the IP camera.
NOTE: Passwords must be at least 12 characters long, with an uppercase letter, a lowercase letter,
and a numeric character or a special character ~@#$%^&*_-+=:;<>
No.
Connector
Pin
Definition
Remarks
1
BNC
-
For analogue video output
2 Alarm I/O
1
Alarm In 2 +
Alarm connection
#Do NOT connect external
power supply to the alarm I/O
connector of the camera.
2
Alarm In –
3
Alarm In 1 +
4
Alarm Out 1 –
5
Alarm Out 1 +
6
Alarm Out 2 –
7
Alarm Out 2 +
3
Power LED
-
For power connection indication (green light)
4
Power
(DC12V / AC 24V) &
RS-485
1
DC 12V +
AC 24V 1
Power connection
2
DC 12V -
AC 24V 2
3
D +
RS-485 connection
4
D –
5 Default Button -
Press the button with a proper tool for at least 20 seconds to restore the
system.
6 microSD Card Slot
Insert the microSD card into the card slot to store videos and snapshots. Do not
remove the microSD card when the camera is powered on.
7 Audio I/O (Line In/Out) Two-way audio transmission
8 Auto Iris - ABF Model: Auto Iris Lens Connection
9
PoE Network
-
For network and PoE connections
10 Network LEDs - For network connection and activity indication
G-Cam/EBC-5101Box IP Camera Quick Guide
ABF Model

Camera Login
The default IP address of the camera is: 192.168.0.250, so to access the camera for the first time, set the IP
address of the PC as follows: 192.168.0.XXX; for example:
IP Address: 192.168.0.100 Subnet Mask: 255.255.255.0
Login ID and Passwort
•Enter the corresponding IP address of the camera in the URL field of the web browser and press "Enter".
•Enter the default user name (root) and password (admin) in the pop-up window. Note that the user name
is case sensitive.
•Change the user password according to the instructions in the section "Logging in to the IP camera for the
first time".
Web browser view
•The figure below shows the home page of the IP camera's web interface. Which
functions are actually available depends on the camera model.
Live view in web browser
G-Cam/EBC-5101
5MP Box IP Camera
Quick Guide
Ver.1.0
NOTE: Quick start guides for configuring the camera using GEUTEBRÜCK - software (G-Set and
GSC-Setup) can be found on our Partner Portal website under Support.
support.geutebrueck.com
The live view in the browser window is done in a H.264/H.265 StreamPlayer,
if this is not executable on your system, the system tries to display a compatible MJPEG view, which is
only possible in reduced quality.
G-Cam/EBC-5101 QIG09.01.2024
Copyright © 2024 Geutebrück. All rights reserved.