GEZE Powerturn IS/TS User manual

Powerturn IS/TS
Powerturn F-IS/TS
Power turn F/R-IS/ TS
EN Installation instructions
164692- 01

Powerturn F/R-IS/TS
2
Contents
1 Symbols and illustrations......................................................................................................................................3
2 Product liability ........................................................................................................................................................3
3 Security .......................................................................................................................................................................3
3.1 Intended use.......................................................................................................................................................................................................3
3.2 Standards.............................................................................................................................................................................................................3
3.3 Reference documents.....................................................................................................................................................................................4
3.4 Safety notices.....................................................................................................................................................................................................4
4 Tools and aids ...........................................................................................................................................................4
5 Types of installation................................................................................................................................................4
5.1 Type of installation transom installation hinge side ...........................................................................................................................4
5.2 Type of installation transom installation opposite hinge side ........................................................................................................4
5.3 Types of installation, hinge action .............................................................................................................................................................5
5.4 Fitting dimensions for the installation types.........................................................................................................................................6
6 Product description ................................................................................................................................................8
6.1 Illustrations of the TS5000L passive leaf unit.......................................................................................................................................8
6.2 Illustrations of the TS4000 passive leaf unit ..........................................................................................................................................9
7 Installing the integrated Powerturn F closing sequence mechanism ............................................... 10
8 Converting the TS units.......................................................................................................................................12
8.1 TS5000L - conversion from DIN right to DIN left..............................................................................................................................12
8.2 TS 4000 - conversion from DIN right to DIN left .................................................................................................................................14
8.3 Connecting the mechanism for integrated closing sequence control of active and passive leaf ...................................15
8.4 Install carry bar............................................................................................................................................................................................... 20
8.5 Install hold-open magnet .......................................................................................................................................................................... 20
8.6 Installing the electrical contact for passive leaf position monitoring....................................................................................... 21
9 Function check ...................................................................................................................................................... 21
10 Commissioning...................................................................................................................................................... 21
11 Service and maintenance .................................................................................................................................. 22
11.1 General information..................................................................................................................................................................................... 22
11.2 Maintenance of mechanism for integrated closing sequence control ..................................................................................... 22
12 Troubleshooting ................................................................................................................................................... 23

Powerturn F/R-IS/TS
3
Symbols and illustrations
1 Symbols and illustrations
Warning notices
In these instructions, warning notices are used to warn against material damage and injuries.
XAlways read and observe these warning notices.
XObserve all measures marked with the warning symbol and warning message .
Warning
symbol
Warning
message
Meaning
CAUTION Danger to persons.
Non-compliance can result in minor injuries.
More symbols and illustrations
Important information and technical notes are highlighted to explain correct operation.
Symbol Meaning
means “important note”
means “additional Information”
XSymbol for an action: This means you have to do something.
XIf there are several actions to be taken, keep to the given order.
2 Product liability
In compliance with the liability of the manufacturer for his products as dened in the German “Product Liability
Act”, compliance with the information contained in this brochure (product information and intended use, misuse,
product performance, product maintenance, obligations to provide information and instructions) must be en-
sured. Failure to comply releases the manufacturer from his statutory liability.
3 Security
3.1 Intended use
The Powerturn F-IS/TS integrated closing sequence control has been designed for mechanical control during the
closing of double-leaf single-action swing leaf doors. The construction components required are a supplement
to the Powerturn drive and must be installed according to these instructions.
The PowerturnF-IS/TS integrated closing sequence control
àis designed for use on re and smoke protection doors.
àmay be used on emergency exit systems.
àmust not be used for hazardous areas.
The PowerturnIS/TS integrated closing sequence control
àmust not be used on re or smoke protection doors.
àmay be used on emergency exit systems.
àmust not be used for hazardous areas.
Any other use than the intended use, such as permanent manual operation of the Powerturn F, as well as any
modication to the product, is not permitted.
Observe the “GEZE Product information for door closers”.
The product should be installed or incorporated in such a way that eortless access to the product is guaranteed
during any repairs and/or maintenance, and that any removal costs do not stand out of proportion to the value of
the product.
3.2 Standards
In addition to the valid standards and regulations, DIN EN 1158 applies to the Powerturn.

Powerturn F/R-IS/TS
4
Tools and aids
3.3 Reference documents
àPowerturn installation instructions
àPowerturn wiring diagram
àInstallation instructions for Powerturn
mechanism for integrated closing sequence
control
àTS5000L installation instructions
àTS4000 installation instructions
àInstallation instructions carry bar
àInstallation instructions and wiring diagram hold-
open magnet
àUser information door closer
The diagrams are subject to change without notice. Use only the most recent version.
3.4 Safety notices
The description of the overall installation of the drive is not the subject of these instructions. This information can
be found in the Powerturn installation instructions.
All the necessary safety notices for conversion or extension to a double-leaf version can be found on the follow-
ing pages.
4 Tools and aids
Tool Size
Drill bit Ø 2 mm
Open-ended spanner SW 5.5
Allen key 1.5 mm
Allen key 2.5 mm
Pozidrive screwdriver
5 Types of installation
5.1 Type of installation transom installation hinge side
Active leaf Passive leaf
5.2 Type of installation transom installation opposite hinge side
Passive leaf Active leaf

Powerturn F/R-IS/TS
5
Types of installation
5.3 Types of installation, hinge action
àThe opening angle of the door always has to be limited by a door stop buer.
àLoads due to wind pressure, negative pressure or excess pressure must be taken into account.
We recommend the installation type involving link arms (wind) for the exterior doors.
The Powerturn IS/TS, Powerturn F-IS/TS, and Powerturn F/R-IS/TS permit, with respect to DIN left and DIN right,
the following buer stop types:
5.3.1 Rail installation and link arm
Type of installation Dimension Powerturn F TS5000L
Transom installation hinge side rail
Reveal depth LT [mm] 0
Door overlap Ü [mm] 0–15
Max. door opening angle TÖW [°] 1) 133 180
Standard roller guide rail L = [mm] 687 415
Lever L = [mm] 330 333
Hinge size [mm] 190
EN class 4–6
Max. door width [mm] O1600 O1400
Type of installation Dimension Powerturn F TS4000
Transom installation opposite hinge side link arm
Reveal depth SD standard and with
sensor link arm [mm]
0–160
Max. door leaf thickness [mm] 150
Max. door opening angle TÖW [°] 1) 135 180
Hinge size [mm] 190
EN class 4–7
Max. door width [mm] O1600 O1600
1) depending on the door construction and door hinges used
For other limits of use see:
àPowerturn installation instructions
àTS5000L installation instructions
àTS4000 installation instructions

Powerturn F/R-IS/TS
6
Types of installation
5.4 Fitting dimensions for the installation types
5.4.1 Type of installation transom installation hinge side
1 Dimensional reference - Centre of hinge/Upper edge of door
2 Covered line-feed possible in the hatched area, e.g. Ø 20 mm for the mains connection or low-voltage
connection
3 Orientation arrow for precise positioning of the mounting plate
Fastening means
Steel/aluminium doors Timber doors
Drive fastening 8 countersunk head screws M6 × 25 and riveting nuts M6 8 wood screws with
countersunk head Ø6 × 50
TS attachment 4 cylinder head screws M6 × 20 and riveting nuts M6 4 wood screws with cylinder
head Ø6 × 50
Intermediate base plate attachment 4 cylinder head screws M6 × 25 and riveting nuts M6 4 wood screws with cylinder
head Ø6 × 50
Fastening standard roller guide rail
Powerturn
2 countersunk head screws M5 × 40 and riveting nuts M5 2 wood screws with
countersunk head Ø5 × 50
Fastening for the vertically adjustable
TS5000L guide rail
2 countersunk head screws M5 × 40 and riveting nuts M5 2 wood screws with
countersunk head Ø5 × 50
Space requirement and fastening
Standard roller guide rail Powerturn Sensor roller guide rail Powerturn Guide rail TS5000L
130
50 50
50
10
10
10
42
36
22
50
26 92
55
4
4 Base top edge of door
5 Space requirement for sensors
1022
92
66
7
6
15
15
41
10
10
4236
31
19
9

Powerturn F/R-IS/TS
7
Types of installation
5.4.2 Type of installation transom installation opposite hinge side
Fastening - DIN right Fastening DIN left
1 Dimensional reference centre of hinge/bottom edge of frame
2 Covered line-feed possible in the hatched area, e.g. Ø 20 mm for the mains connection or low-voltage connec-
tion
3 Orientation arrow for precise positioning of the mounting plate
Fastening means
Steel/aluminium doors Timber doors
Drive fastening 8 countersunk head screws M6 × 25 and riveting nuts M6 8 wood screws with
countersunk head Ø6 × 50
TS attachment 4 cylinder head screws M6 × 20 and riveting nuts M6 4 wood screws with cylinder
head Ø6 × 50
Intermediate base plate attachment 4 cylinder head screws M6 × 25 and riveting nuts M6 4 wood screws with cylinder
head Ø6 × 50
Fastening for the Powerturn link arm 2 cylinder head screws M6 × 16 and riveting nut M5 2 wood screws with cylinder
head Ø5 × 20
Fastening for the TS4000 link arm 2 cylinder head screws M5 × 16 and riveting nut M5 2 wood screws with cylinder
head Ø5 × 20
Fastening the adapter for the Powerturn
sensor link arm
2 countersunk head screws M6 × 20 and riveting nut M6 2 wood screws with
countersunk head Ø5 × 35
Space requirement and fastening
Powerturn link arm Link arm TS4000
130
50
50
10
10
42
46
22
50
72
8*
43
50
5 5
4
4 Base lower edge of lintel
5 Space requirement for sensors
* Important functional dimension
11*
35
41

Powerturn F/R-IS/TS
8
Product description
6 Product description
6.1 Illustrations of the TS5000L passive leaf unit
6.1.1 TS5000L passive leaf unit transom installation hinge side DIN right

Single side panel (for
continuous cover)
Double side panel (for split cover)
1 Rocker for integrated closing sequence control
2 Deection pulley
6.1.2 TS5000L passive leaf unit transom installation hinge side DIN left


Single side panel (for
continuous cover)
Double side panel (for split cover)
1 Rocker for integrated closing sequence control
2 Deection pulley

Powerturn F/R-IS/TS
9
Product description
6.2 Illustrations of the TS4000 passive leaf unit
6.2.1 TS4000 passive leaf unit transom installation opposite hinge side DIN right

Single side panel (for
continuous cover)
Double side panel (for split
cover)
1 Rocker for integrated closing sequence control
6.2.2 TS4000 passive leaf unit transom installation opposite hinge side DIN left

Single side panel (for
continuous cover)
Double side panel (for split
cover)
1 Rocker for integrated closing sequence control

Powerturn F/R-IS/TS
10
InstallingtheintegratedPowerturnFclosingsequencemechanism
7 Installing the integrated Powerturn F closing sequence mechanism
1
2
SW 2.5
3
452.5 Nm 6
7
Transom installation opposite hinge side
Installation position brake unit: Opposite Hinge Side (OHS)
Transom installation hinge side
Installation position brake unit: Hinge Side (HS)

Powerturn F/R-IS/TS
11
InstallingtheintegratedPowerturnFclosingsequencemechanism
8
9
SW 5.5
1 Nm
10
SW 2.5
2.5 Nm
11
XDuring installation of the setting lever, pay attention to the alignment of the mechanism for integrated closing
sequence control (see below).
Types of installation:
àTransom installation - hinge side, DIN left
àTransom installation - opposite hinge side, DIN right
Types of installation:
àTransom installation - hinge side, DIN right
àTransom installation - opposite hinge side, DIN left

Powerturn F/R-IS/TS
12
Converting the TS units
8 Converting the TS units
8.1 TS5000L - conversion from DIN right to DIN left
This chapter describes the conversion work necessary if TS5000L is to have a DIN left installation.
8.1.1 TS5000L is delivered for DIN right installation from the factory
8.1.2 Converting the TS5000L











Powerturn F/R-IS/TS
13
Converting the TS units

















Powerturn F/R-IS/TS
14
Converting the TS units
8.2 TS 4000 - conversion from DIN right to DIN left
This chapter describes the conversion work necessary if TS 4000 is to have a DIN left installation.
8.2.1 TS 4000 transom installation opposite hinge side is delivered for DIN right installation from the factory
8.2.2 Converting the TS 4000







Powerturn F/R-IS/TS
15
Converting the TS units












8.3 Connecting the mechanism for integrated closing sequence control of active and
passive leaf
XInstall the drive and lever. For drive installation, see installation instructions Powerturn, “prepare for installa-
tion” and “Installation” sections. For TS installation, see the chapter 5.4.
XInstallation of the guide rail and lever of the TS5000L-shaft and the adjustment of the valves, see TS5000L
installation instructions.
àInstallation of the link arm of the TS4000 and the adjustment of the valves, see TS4000 installation instructions.
àUse the pre-mounted screw in the TS4000 shaft for fastening the link arm on the TS4000-shaft.
XUse the pre-mounted screw in the TS5000L-shaft for fastening the lever, not the screw enclosed with the
screw accessories for the TS5000 guide rail.

Powerturn F/R-IS/TS
16
Converting the TS units
8.3.1 Mounting the door closer unit
For the installation dimensions, see chapter 5.4.
TS5000L




 

TS4000




 

Connection of the active and passive leaf drive:


Passive leaf (1) Active leaf (2)

Powerturn F/R-IS/TS
17
Converting the TS units
XWith continuous cover, remove the side panels.
XDrill the passage in the side panel for the split cover and deburr (depending on the route of the wire cable):
Ø 2 mm
Route of wire cable near the passive leaf unit:
TS5000L DIN right TS4000 DIN right
TS5000L DIN left TS4000 DIN left

Powerturn F/R-IS/TS
18
Converting the TS units
Route of wire cable near the control:
 
Position of setting lever with the brake closed Position of setting lever with the brake opened
1 Motor 1 Motor

Powerturn F/R-IS/TS
19
Converting the TS units
Attach the wire rope and spring on the wire rope tensioner
1
2
3
1 2
4
SW 1.5
~0.2 Nm
Set screw (1), tension spring (2)
5
3
~0.2 Nm
Position of the setting lever (3) = brake opened, active leaf closing.

Powerturn F/R-IS/TS
20
Converting the TS units
Set the retaining action of the integrated closing brake
SW 2.5
The correct setting of the entire mechanism for integrated closing sequence control has been achieved when, with
the brake closed and passive leaf closed, the setting lever takes up the position as designated for the open brake.
The wire rope must be tensioned both with opened and closed integrated closing brake between the passive
and active leaf unit.
8.4 Install carry bar
CAUTION!
Danger of crushing.
Body parts can become caught between the door leaves
XInstall carry bar.
A carry bar must be installed in order to protect the main closing edge.
XInstall the carry bar in compliance with the included installation instructions.
8.5 Install hold-open magnet
A hold-open magnet must be installed for the hold-open function of the passive leaf.
XInstall the hold-open magnet so as to ensure sucient door opening.
The hold-open magnet must be permanently and reliably attached to the building.
XSafeguard the connection cable between the hold-open magnet and the Powerturn against outside access.
XConnect the hold-open magnet in compliance with the included wiring diagram and the Powerturn wiring
diagram, “Hold-open system Powerturn F-IS/TS, F/R-IS/TS” section.