GEZE Slimdrive SC Manual

Slimdrive SC/SCR
Slimdrive SLT
Slimdrive SL
EC Drive/Powerdrive
Sliding Door Drive for Automatic Doors
Operation &
Maintenance Manual
GB
GEZE UK Ltd is part of the GEZE Worldwide Group of Companies

Contents
Safety Instructions 3
General rules of safety and accident protection.
System Description 4
Detailed description of drive components
Occupier Safety Tests 5
Safety check list to be adhered to by the User
Occupier Safety Test ( continued ) 6
Safety check list to be adhered to by the User
Operational Switches 7
Detailed review of control switches.
Fault Codes 8-9
Detailed review of all fault codes
Power Failure 10
Detailed review of power failure and fire alarm procedure
General Cleaning & Maintenance 11
Detailed review of cleaning and maintenance procedures.
Service Information 12
Contact numbers, Warranty & Post Warranty information.
2
GEZE UK Ltd is part of the GEZE Worldwide Group of Companies

Safety Instructions
General Safety Instructions
Before starting to use the door, read this user manual with care and comply with the following
safety instructions at all times:
•The Slimdrive SL/SLT automatic sliding door operator is only intended for normal usage
with automatic doors.
•Please comply with relevant accident prevention regulations.
•Please follow the guidelines for BS 7036 1996 Safety at Powered Doors for Pedestrian
Use.
•Please adhere to the operating, servicing and repair conditions specified by GEZE.
•Servicing and repair work may only be carried out by properly trained GEZE personnel or
authorized GEZE partner.
•Isolate all power before removing cover.
•IMPORTANT: The cover may only be removed by properly trained personnel authorized
by GEZE.
•GEZE does not accept responsibility for damage resulting from unauthorized modification
of the equipment. Warranty will be void if damage is caused from unauthorized
modification.
3
GEZE UK Ltd is part of the GEZE Worldwide Group of Companies

System Description
Types of Door Leaves
Glass doors consisting of either single of double glazed glass.
Doors with timber, metal or aluminium frames.
Drive
Low wear high capacity DC Motor.
Extremely quiet enclosed running gear.
Power transmission via toothed belts: deflection rollers in precision bearings.
Self learning processor control.
Permanent position sensing of door leaves by means of non-contact distance measuring
System.
Determination of door leaf weight by means of acceleration meter.
Adjustable hold open time.
Automatic error detection.
Error indication at programme switch.
Audio signal in case of error.
Opening and closing speed individually adjustable.
Automatic adjustment of opening time dependent on traffic.
Connection to fire alarm ( optional ).
Electro magnetic locking to secure the door leaves against being forced open ( Optional )
Automatic reversing function with adjustable reversing pressure. The door opens
automatically, should it meet an obstacle during closure.
Emergency opening via an integrated battery back up in case of power failure.
Integrated mains isolator.
Closing force limited to < 150 N.
GEZE UK Ltd is part of the GEZE Worldwide Group of Companies
4

Occupier Safety Test
Extract from BS 7036 : Part 2 : 1996 ( Annexes )
This section provides a checklist for occupier safety tests on powered doors, which suit
the majority of installations. However, the person / organization responsible for the
operation and maintenance of the doors should consider each individual installation and
adopt a safety test procedure that is suitable for that installation. Additional tests to those
given in this section may be necessary if specified by the manufacturer.
Occupier safety check list for all types of powered sliding doors
The occupier is responsible for undertaking the following test procedure which should be
carried out at least weekly unless a different frequency for tests is identified in the Hazard
Analysis and Risk Assessment ( See 4.6.2.1 of Part 1 ).
For safety reasons it should not be assumed that equipment is working safely. There
should be no notice boards, literature racks, merchandise displays, or other distractions or
obstructions in the vicinity of the door that may congest or inhibit the traffic flow.
If a fault is found which affects the safe operation of the door, the door operating
equipment should be switched off and the door made safe. Use of the door should not be
re-instated until an authorized technician has undertaken repairs.
Automatic Activation Devices
Sensor Activation (if fitted)
1) Test Sensors by walking towards the door opening. The door should start to open
when a person is approximately 1400mm (5 ft ) from the door. The door should slide
smoothly to the open position and stop without impact.
2) Step out of the activation zone. After a delay (normally 1s to 5s ) the door should close
smoothly.
3) Repeat 1 and 2 on the other side of the door opening if the door has two way
operation.
Safety Devices
4) Various devices are available to protect the threshold area by preventing a door from
closing whilst the area is occupied. These include presence-sensing devices, hold
open beams or safety mats. Test these devices as follows:
a) Presence Sensing Devices. If presence sensing devices are fitted, place the test
object (see 8.4.2 of Part 1) within 150 mm of the plane of movement of the door
(but not interrupting the safety light barrier) and verify the door remains open for a
minimum of 30 s. After a minimum of 30 s it is allowable for the door to close.
b) Hold Open Beams. If hold open beams are fitted, place the test object ( see 8.4.2
of part 1 ) on the threshold and verify the door remains open.
5
GEZE UK Ltd is part of the GEZE Worldwide Group of Companies

General Tests
5) Check that the door area has no tripping or slipping hazards.
6) Check all door panels for broken or cracked glass.
7) Check that all doors have signs correctly displayed at recommended viewing heights.
8) Check the position and security of associated screens and barriers.
9) Check the operation of manual activation, or remote activation, or emergency stop
button if fitted.
10) Check for distractions or obstructions in the vicinity of the door.
Extract from BS 7036 : Part 1 : 1996 ( 4.6.2.1 Occupier Safety Checks )
To ensure continued operation of a powered door installation, the installation and its
environment should be subjected to systematic operational checks as often as is
appropriate to the type of installation and its traffic flow. This should be assessed with
reference to the Hazard Analysis and Risk Assessment carried out under 4.1.4, e.g. in
high traffic areas such as shops, hospitals and airports, an appropriate rate would be at
least once a week using the tests given in parts 2 to 5.
Extract from BS 7036 : Part 1 : 1996 ( 8.4.2 Test Object )
The following test object should be used.
a) For presence sensing devices, a cardboard box of approximate dimensions 250mm x
150mm x 710mm high ( 10in x 6in x 28in high ) is a suitable test object.
b) For motion sensing devices, testing is achieved by the tester approaching the door
from several directions in turn.
6
GEZE UK Ltd is part of the GEZE Worldwide Group of Companies

Operational Switches
Operation of Settings
This type of programme switch carries out various functions. They are; select mode of
operation, view error messages and programme and service the system. The modes of
operation are as follows.
Automatic Mode ( Au )
Whilst in this mode the door will be activated automatically by the relevant form of sensor
fitted i.e. Radar, Push Pad etc. The door will power open, stay open for a designated time
( normally 1 to 5 seconds ) and then power close. There is also a possibility to open the
doors to a reduced distance ( Winter Setting ). This is achieved by pressing the
Automatic and Hold Open buttons at the same time. A small red LED is illuminated
above the snowflake whilst the door is in Winter Setting. To return to the summer setting
repeat the process of pressing Automatic and Hold Open at the same time.
Hold Open Mode ( Ho )
Whilst in this function the door will power open and be held permanently open.
Night Mode ( ni )
Whilst in this mode the drive unit is off. All activation and safety devices are isolated once
the door is fully closed. If an integrated electric lock is fitted, this will be engaged
automatically to secure the doors ( if fitted ).
Exit Only ( Eo )
Whilst in this mode the external activation device is isolated. The internal activation device
is still active. This enables traffic to leave the premises at closing time.
Program Switch
Press simultaneously
for winter setting
Press once for
automatic
hold open
Press once for
Press once for
one way traffic
night mode
Press once for
Red LED Au
LED Display
Service Indicator
IMPORTANT NOTICE
If manual locks are fitted to the door leaf, please ensure they are UNLOCKED prior to
switching the drive unit into one of the operational modes. Also switch the drive unit to
NIGHT MODE before locking the door.
7
GEZE UK Ltd is part of the GEZE Worldwide Group of Companies

Fault Codes – SL 1.7 to SL 1.9
Fault Messages
If a fault occurs on the system a 2-digit number will be displayed on the program switch.
This will flash every 20 seconds. Up to 5 separate fault codes may be issued in
succession. If the system has been appropriately configured, an audible warning also
occurs. To assist in fault diagnosis, please advise any fault codes to our office without
delay.
Code and description of all error messages. Please confirm this code when reporting the
fault to the Service Dept.
Error Meaning
01 24V voltage internal (no voltage)
02 12V voltage internal (no voltage)
03 230V voltage supply (no voltage)
10 No signal from the position indicator
12 Faulty motor
13 Safety sensor 1 (contact closed)
14 Flat battery 14V
15 Display program switch (no signal)
16 Lock not locking
17 Lock not un-locking
19 Safety sensor 2 (contact closed)
27 Safety sensor 1 (contact open)
29 Safety sensor 2 (contact open)
32 Sabotage switch is activated
33 Second control (sluice, draught lobby)
35 Chemist Setting
37 Internal Activation (contact closed)
39 External Activation (contact closed)
40 Key switch Contact (contact closed)
41 Safety sensor 1 (contact open)
42 Emergency locking (contact closed)
45 Drive control (hot)
46 Temperature sensor motor
47 Temperature sensor control
48 Drive overheated
8.8 No communication between control & DPS.
8
GEZE UK Ltd is part of the GEZE Worldwide Group of Companies

Fault Codes – SL DCU 1
Fault Messages
If a fault occurs on the system a 2-digit number will be displayed on the program switch.
This will flash every 20 seconds. Up to 5 separate fault codes may be issued in
succession. If the system has been appropriately configured, an audible warning also
occurs. To assist in fault diagnosis, please advise any fault codes to our office without
delay.
Code and description of all error messages. Please confirm this code when reporting the
fault to the Service Dept.
Error Meaning
01 24V voltage internal (no voltage)
02 12V voltage internal (DCU 100 no voltage)
03 230V voltage supply (no voltage)
10 No signal from the position indicator
11 Motor defective (DCU100)
13 Safety sensor 1 (contact closed)
15 No communication between controller and DPS
16 Lock defective
17 Lock not unlocking
18 Lock and unlock message both active
19 Safety sensor 2 (contact closed)
27 Safety sensor 1 (contact open)
28 Motor relay on main PCB defective
32 Tamper switch is activated
33 Second control (sluice, draught lobby)
35 Pharmacy contact activated longer than 4 minutes
36 Internal redundancy fault on processor
37 Internal Activation (contact closed longer than 4 minutes)
39 External Activation (contact closed longer than 4 minutes)
40 Key switch Contact (contact closed longer than 4 minutes)
41 Safety sensor 1 (contact open longer than 1 minute)
42 Emergency locking (contact closed longer than 4 minutes)
45 DCU100 Drive control (hot) temperature exceeds 110ºC
46 Temperature sensor motor defective
47 Temperature sensor on processor defective
48 Motor or controller overheated temperature exceeds 115ºC
60 Fault on DCU100 main PCB
61 Battery flat or disconnected
90 Processor defective
91 No signal from tacho
X.X Leaf position unknown (dot in left hand display)
LE (EL) Fault during controller learning
8.8 No communication between processor and DPS
9
GEZE UK Ltd is part of the GEZE Worldwide Group of Companies

Power Failure
Power Failure
If a power failure occurs, first check the fuse at the customer end. The presence of a
battery determines whether the door opens or closes when the power fails. In most cases,
the door will open in the event of power failure unless in Night mode (ni)
Battery present If the door is to be locked from the outside, operate the outside key switch
(>4 seconds) until the programme switch lights up. Select ni by pressing
the half moon symbol once: the door opens, closes and locks once.
If the battery is discharged see “No battery present or battery discharged”
No battery present Open: unlock door manually and open door leaf by hand
or battery Close: close the door leaf by hand and manually lock the door
discharged
After power failure Door automatically returns to the previously selected operating state
Or
If the door is locked, it automatically changes to “Night” mode.
Fire Alarm activation (if fitted)
When the doors are in the “Automatic “setting they will power open and
remain in the fully open position until the fire alarm has been reset. When
the doors are in the “Night” position they will remain closed/locked so as
not to compromise security
Service Indicator
When the service indicator LED is lit a annual service will be req`d
10
GEZE UK Ltd is part of the GEZE Worldwide Group of Companies

General Cleaning & Maintenance
Maintenance of Drive Unit
Aluminium Cover
Wipe Clean with a damp cloth. DO NOT allow water to enter through the drive unit cover.
Activation & Safety Sensors
Ensure plastic lenses are clean & dust free. Wipe with a dry soft cloth if necessary.
Preventative Maintenance
GEZE strongly advise that a preventative maintenance programme is entered into, in line
with the recommendations of BS 7036: Safety at powered doors for Pedestrian Use.
An Authorized Technician to BS 7036 must carry out any servicing.
Fabricated Doors / Screenwork only - See separate section for electrical drive unit covers.
Atmospheric deposits, sulphurous acids, carbon dioxides and other chemicals in the air
will discolour and tarnish all metalwork, and in time cause corrosion. Regular maintenance
prevents atmospheric deposits building up and attacking the metals.
Anodized Aluminium.
Wash with mild soap and water or a mild detergent solution, rinse down with clean water
and dry off with a soft cloth or chamois leather. Apply a liquid wax polish to protect the
metal from the atmosphere.
AVOID : Metal polish of any kind, abrasive cleaners, strong alkalines or acids, and the use
of ammonia based cleaners for washing windows as they can cause staining of the
surrounding framework.
Recommended frequency - WEEKLY.
P olyester Powder Coated Aluminium.
As with any organic coating, in order to retain the aesthetic properties, it is recommended
that the coating be regularly maintained. Wash at intervals of not more than three months
using a solution of warm water and mild detergent. (e.g. 5 % Teepol solution or mild
washing up liquid.) All surfaces should be cleaned using a soft cloth or sponge but nothing
harsher than a natural bristle brush.
AVOID : Abrasive cleaners or cleaning solutions such as ketones, esters, or alcohols.
Recommended frequency - THREE MONTHLY (depending on environment.)
Polished or Satin Stainless Steel.
Wash away grime and grit with luke warm soapy water or a mild detergent solution using
a nailbrush for awkward crevices or corners. Repeat with clean water. Dry and polish with
a soft duster or chamois leather.
AVOID : Metal polishes, and all abrasives, toxic materials, acids, strong alkalines, nylon
pads, wire wool.
Recommended frequency - WEEKLY.
Glass.
Wash as often as possible with clean water and a chamois leather, scrim or squeegee,
and dry off. The occasional application of a proprietary window cleaner or polish can be
beneficial providing it does not contain ammonia. Advise may be given by a reputable
window cleaning company.
11
GEZE UK Ltd is part of the GEZE Worldwide Group of Companies

GEZE UK Ltd is part of the GEZE Worldwide Group of Companies
Service Information
We are committed to the very best in customer service. To ensure rapid response and
total peace of mind we offer 24 hour 7 day a week service and repair for all makes of
automatic and manual doors throughout the UK.
Warranty Period - Up to 12 months from installation
Fully comprehensive GEZE parts and labour warranty which covers all faults other than
those caused by abuse.
For Nationwide Assistance call 08456 777781
Post - Warranty period
Following the warranty period - GEZE provides a range of Service Contracts to suit
individual site requirements. The current BS7036 recommends that powered doors are
serviced twice per year - our Service Contracts are therefore based on this important
recommendation.
A comprehensive, 24 hour service,
nationwide – from your local office…
GEZE Service Midlands GEZE Service South East
Blenheim Way Unit 15, Farnborough Business Centre
Fradley Park Eelmoor Road
Lichfield Farnborough
Staffordshire Hampshire
WS13 8SY GU14 7XA
Tel: [phone] Tel: [phone]
Fax: [phone] Fax: [phone]
GEZE Service South West GEZE Service North
Unit 39, Old Mills Industrial Estate Unit 24a, Oak Road
Old Mills West Chirlton North Industrial Estate
Paulton NorthShields
Bristol Tyne&Wear
BS39 7SU NE29 8SF
Tel: [phone] Tel: [phone]
Fax: [phone] Fax: [phone]
12