GEZE UFO-NT IP Reference guide

UFO-NT
2
Table of contents
Symbols and illustrations ..................................................................................................................................................4
Validity .....................................................................................................................................................................................4
Product liability.....................................................................................................................................................................4
1 Notes............................................................................................................................................................................5
1.1 Important safety instructions......................................................................................................................................................................5
1.2 Installation information .................................................................................................................................................................................5
1.3 Safe operation ...................................................................................................................................................................................................5
1.4 Inspection of installed system.....................................................................................................................................................................5
1.5 Disposal of the door system.........................................................................................................................................................................6
2 Abbreviations............................................................................................................................................................6
3 Electrical data............................................................................................................................................................6
4 Supply terminals ......................................................................................................................................................7
5 "Open" and "close" safety sensor.......................................................................................................................9
5.1 Safety sensor strip pair GC 338....................................................................................................................................................................9
5.2 Safety sensor GC342.....................................................................................................................................................................................12
5.3 Safety sensor GC334.....................................................................................................................................................................................14
5.4 Safety sensor GC335.................................................................................................................................................................................... 16
6 Mechanical contact...............................................................................................................................................18
6.1 Key switch..........................................................................................................................................................................................................18
7 Contact sensor inside...........................................................................................................................................19
7.1 GC 302 R radar movement detector........................................................................................................................................................19
7.2 Push button (oating normally opened contact) ..............................................................................................................................19
8 Contact sensor outside....................................................................................................................................... 20
8.1 GC 302 R radar movement detector....................................................................................................................................................... 20
8.2 Push button (oating normally opened contact) ............................................................................................................................. 20
9 Radio control.......................................................................................................................................................... 21
9.1 Radio reception board WRB-5 .................................................................................................................................................................. 21
9.2 Insert the radio reception board WRB-5 to the control circuit board DCU800...................................................................... 21
9.3 Transmitting module WTM........................................................................................................................................................................ 21
10 Push And Go........................................................................................................................................................... 22
11 Congurable inputs............................................................................................................................................. 22
11.1 MPS ..................................................................................................................................................................................................................... 22
11.2 2-leaf opening and 1-leaf opening ......................................................................................................................................................... 23
11.3 Sabotage........................................................................................................................................................................................................... 23
11.4 Active leaf closed position ......................................................................................................................................................................... 23
11.5 Emergency lock.............................................................................................................................................................................................. 24
11.6 Additional contact sensors (P-KI, P-KA)................................................................................................................................................. 24
11.7 Switch function .............................................................................................................................................................................................. 24
11.8 Control reset.................................................................................................................................................................................................... 25
11.9 Double push button (1-leaf / 2-leaf door opening) .......................................................................................................................... 25
11.10 STOP ................................................................................................................................................................................................................... 26
11.11 Closed position detection.......................................................................................................................................................................... 26
11.12 WC control unit............................................................................................................................................................................................... 27
11.13 1 leaf open........................................................................................................................................................................................................ 27

UFO-NT
3
12 Congurable outputs.......................................................................................................................................... 27
12.1 Congurable output PA1 ............................................................................................................................................................................ 27
12.2 Congurable output PA2.............................................................................................................................................................................31
13 Electric strike .......................................................................................................................................................... 33
13.1 24V DC electric strike supplied on drive side...................................................................................................................................... 34
13.2 Customer-supplied 12 V AC electric strike ........................................................................................................................................... 34
13.3 Bolt message................................................................................................................................................................................................... 35
13.4 Activation delay for lock switch contact............................................................................................................................................... 35
14 Free cable connections....................................................................................................................................... 35
15 WC control............................................................................................................................................................... 36
16 Mode of operation ............................................................................................................................................... 37
16.1 Programme switch........................................................................................................................................................................................ 37
16.2 Setting the mode of operation using push buttons or switches ................................................................................................ 39
17 2-leaf drives............................................................................................................................................................. 40
17.1 Two automated door leaves...................................................................................................................................................................... 40
17.2 Connection via system cable RS485....................................................................................................................................................... 40
18 Motor ........................................................................................................................................................................ 40
19 Control.......................................................................................................................................................................41
20 Commissioning and service.............................................................................................................................. 42
20.1 Commissioning............................................................................................................................................................................................... 42
20.2 Teaching run.................................................................................................................................................................................................... 42
20.3 Teaching a 1-leaf system............................................................................................................................................................................. 43
20.4 Teaching a 2-leaf system............................................................................................................................................................................. 44
20.5 Forces and speeds......................................................................................................................................................................................... 45
21 Disconnected mode ............................................................................................................................................ 45
22 Free swing function............................................................................................................................................. 46
23 Resilience to external inuences or load due to wind pressure........................................................... 46
24 Door closer operation......................................................................................................................................... 46
25 Low-energy mode................................................................................................................................................ 47
26 Servo mode ............................................................................................................................................................ 48
26.1 Servo support without re alarm with additional torque.............................................................................................................. 48
26.2 Servo support with re alarm with additional torque..................................................................................................................... 49
27 Service menu ........................................................................................................................................................ 50
27.1 Service terminal ST220................................................................................................................................................................................ 50
27.2 Connecting service terminal ST220........................................................................................................................................................ 51
27.3 Service menu ST220 ..................................................................................................................................................................................... 52
27.4 DPS (DPS).......................................................................................................................................................................................................... 68
27.5 Service menu DPS ......................................................................................................................................................................................... 68
28 Fault messages ST220 and DPS ....................................................................................................................... 76

UFO-NT
4
Symbols and illustrations
Warning notices
Warning notices are used in these instructions to warn you of property damage and personal injury.
XAlways read and observe these warning notices.
XObserve all measures marked with the warning symbol and warning word.
Warning
symbol
Warning word Meaning
DANGER Danger to persons.
Non-compliance will result in death or serious injuries.
ATTENTION Danger to persons.
Non-compliance may result in death or serious injuries.
CAUTION Danger to persons.
Non-compliance may result in minor injuries.
Further symbols and means of representation
Important information and technical notes are highlighted to explain correct operation.
Symbol Meaning
means "important information";
information on avoiding material damage, understanding a concept or optimising workows.
means "additional information"
XSymbol for an action: This means you have to do something.
XIf there are several actions to be taken, keep to the given order.
Compliant with EN 16005 Symbol in a table or in information concerning safety sensors.
Not compliant with EN16005 Symbol in a table or for a piece of information on sensors that do not cor-
respond to EN 16005.
Fire protection door Symbol for re protection door
Not permissible for re protec-
tion door
Symbol "Not permissible for re protection door"
Validity
àValid from software version DCU8 V U1.8
àHardware revision DCU800 from Rev F
Product liability
In compliance with the product manufacturer liability as dened in the German “Product Liability Act”, the
information contained in this brochure (product information and intended use, misuse, product performance,
product maintenance, obligations to provide information and instructions) must be observed. Failure to comply
with this information releases the manufacturer from its statutory liability.

UFO-NT
5
Notes
1 Notes
1.1 Important safety instructions
To ensure personal safety, it is important to follow these safety instructions.
XKeep these instructions.
àOnly specialists authorised by GEZE are permitted to carry out installation, commissioning and maintenance
work.
àUnauthorised modications to the system release GEZE from liability for any resulting damages.
àGEZE makes no guarantee for combinations with third-party products. In addition, only original GEZE parts
may be used for repair and maintenance work.
àConnection to the mains voltage must be carried out by a qualied electrician. The mains connection and
equipment ground conductor test must be performed in accordance with VDE 0100 Part 610.
XThe customer must install a circuit breaker as a mains separator, whose rated value is aligned to the type, pro-
le, method of installation and the ambient conditions of the local power supply line. The circuit breaker must
have a minimum and maximum rating between 4 A and 16 A.
àAttach safety stickers to glass leaves (mat. no. 081476).
XIn accordance with Machinery Directive 2006/42/EC, a safety analysis must be performed and the door system
must identied in accordance with CE Identication Directive 93/68/EEC before the door system is commis-
sioned.
àObserve the latest versions of directives, standards and country-specic regulations, in particular:
àASR A1.7 "Directives for doors and gates"
àEN 16005 "Power operated pedestrian doorsets – Safety in use – Requirements and test methods"
à"Guidelines for hold-open systems"
àDIN VDE 100-600 "Installation of low-voltage systems - Part 6 Tests"
àDIN EN 60335-2-103 "Household and similar electrical appliances; Particular requirements for drives for
gates, doors and windows"
àAccident Prevention Regulations, in particular BGV A1 (VBG1) "General Regulations"
BGV A3 (VBG4) "Electrical Installations and Resources"
1.2 Installation information
XOnly use the cables prescribed in the cable plan provided. Cables must be shielded in compliance with the
wiring diagram.
XAlways use insulated wire-end ferrules for wire cores.
XInsulate wires that are not used.
XSecure loose, internal drive cables with cable ties.
XObserve the maximum permitted overall current drain required to supply the periphery.
1.3 Safe operation
XSecure the workplace against unauthorised entry.
XPay attention to the swivelling range of long system parts.
XSecure control box against falling.
XBefore working on the electrical system, disconnect the power supply (mains and battery) and check that no
voltage is present. Note that if an uninterruptible power supply (UPS) is used, the system will still be supplied
with power despite the fact that the power supply is disconnected.
àRisk of injury by moving parts (drawing in of hair, clothing, ...) when a drive is opened.
àRisk of injury caused by unsecured crushing, impact, drawing-in or shearing spots.
àRisk of injury caused by sharp edges in the drive.
àRisk of injury due to glass breakage.
àDanger of injury through link arm or lever arm snapping back. Disconnect motor from the control only if
spring is not under tension.
àDanger of injury when working at heights.
àOnly operate the drive with a connected latching action switch.
1.4 Inspection of installed system
XCheck the measures for securing or preventing crushing, impact, shearing or pull-in spots.
XCheck the function of the presence sensors and movement detectors.
XCheck the protective earth connection to all metal parts that can be touched.

UFO-NT
6
Abbreviations
1.5 Disposal of the door system
àThe door system is made up of materials that should be sent for recycling.
The individual components have to be sorted in accordance with their material type.
àAluminium (proles, cover, return pulleys, sliding blocks, ...)
àIron (drivers, screws, ...)
àPlastic
àElectronic components (dead bolt, motor, control, transformer, sensors, ...
àCables
The parts can be disposed of at the local recycling depot or by a scrap recycling company.
àBatteries contain pollutants and heavy metals. Do not dispose of with household waste.
Turn over rechargeable batteries to your local recycler.
2 Abbreviations
Wire colours
BN brown
BK black
BU blue
GN green
GY grey
YE yellow
OG orange
PK pink
RD red
TQ turquoise
VT violet
WH white
Connections, terminals and plugs
AU Automatic
BS Hinge side
BGS Opposite hinge
side
DO Hold open
DPS DPS
END Latching action
GF Active leaf
GND Reference poten-
tial
KA Contact sensor
outside
KB Mechanical con-
tact
KI Contact sensor
inside
LK Luster terminal
LS Exit only
MPS Mechanical programme
switch
NA Night
PA Congurable output
PE Congurable input
RBM Radar movement detec-
tor
RES Reset switch
RM Bolt message
RSZ Smoke control unit
RS485 Communication signal to
DPS and second drive
OFF OFF mode of operation
SF Passive leaf
STOP Stop
SCR Screen
SO Opening safety sensor
SIS Closing safety sensor
STG Fault
TK Door transmission cable
TOE Electric strike
TST Test signal for safety sen-
sors
24V Supply voltage for exter-
nal devices
24VSENS Supply voltage for sen-
sors, connected after
setting the ECO mode
3 Electrical data
Mains voltage 230 V AC –15%, +10%
Frequency 50Hz
Protection rating I
Capacity rating 200W
Mains connection Fixed connection (installation cable or cable connection)
Primary fuse –
Secondary fuse 10A slow-blow, 5×20mm
Secondary voltage (transformer) 33VAC (46 V DC)
Control voltage for external components 24VDC ±10%
Output current control voltage 24 V 1200mA permanently 1800mA briey (5s, duty ratio
30%)
Fuse protection <24V 2.5A; reversible
Temperature range –15…+50°C
IP rating IP version IP67
F version IP62

UFO-NT
7
Supply terminals
4 Supply terminals
DCU800
12
24V
GND
6
1 RS485 passive leaf
2 FREE

UFO-NT
8
Supply terminals
DCU802
DPS-RS485
43
20 3214 1231
41 42 21 9876 02 4215756552 19897969553 52 51
KB
4 10 4 1 11 10 4 1 13 36 35 1 33 32 31 2 1
KI KA SIS SIO N.N. TOE
46
46
44 45
CANL
CANH
GND CAN(ISO)
CAN
KA
DPS
RS485
DCU106
2
1 Socket DCU103
2 FREE
Optional:
CAN interface DCU103, Mat. no. 119952
S1: Terminating resistor ON / OFF

UFO-NT
9
"Open" and "close" safety sensor
5 "Open" and "close" safety sensor
XIn the case of 2-leaf systems, connect the safety sensors of the active leaf with the active leaf control and those
of the passive leaf with the passive leaf control.
XInstall the sensor for monitoring closing on the door leaf, opposite hinge side.
If the SIS is activated during closing, the door reverses and opens again.
XInstall the sensor for monitoring opening on the door leaf, hinge side.
The door stops if the SIO is activated during opening.
For detection, the sensor output is open (GND applied to SIS or SIO input).
XCheck the function and correct setting of the sensors during commissioning and when servicing the assembly.
àTo operate the DPS DPS see chapter 27.4 "DPS (DPS)".
àTo operate the service terminal ST220 see chapter 27.1 "Service terminal ST220".
The state of the drive to which the ST220 is connected is displayed.
XPress the button.
XSelect "Active leaf para" or "Passive leaf para" using the or key and press the key.
XIn the selection menu, use the or key to select "Signals" and then press the key.
For further settings, see the descriptions below.
The wall blanking range of the sensor strip SIO is set automatically during the teaching procedure.
If necessary, it can be changed with DPS or ST220 via the service menu, with
àDPS: Set the parameter aB to the desired wall blanking range (1° to 99°)
àST220: Set "Input signals", "SI3 – terminal SIO1", "SI3 wall blanking area" to the desired value (1° to 99°).
5.1 Safety sensor strip pair GC 338
XFollow installation instructions GC 338.
àAccessories:
àSpot nder, mat. no. 112321
àThe connector plug of the GC 338 has 6 poles. Terminal 6 is not occupied.
àTo save energy, the Powerturn can automatically switch the GC 338 to standby mode if it is not required. In order to
do so, the Powerturn must be equipped with rmware above V1.8.
à“Energy-saving mode” must be activated on the Powerturn and on the GC 338.
àBoth operating modes conform to DIN 18650 or EN 16005.
Standard operation
XSet DIP switch 3 (TST/SBY) on the GC 338 interface module to ON (default setting).
XSet the "Testing" parameter.
àDPS: Set
Te to 01 (testing with 24 V).
àST220: Set "Output signals", "Testing SI" to "Testing with 24 V".
Energy-saving mode
The SIS and SIO must be set to testing “Energy-saving mode”.
XSet DIP switch 3 (TST/SBY) on the GC 338 interface module to OFF.
XSet the "Testing" parameter.
àDPS: Set
Te to 03
(energy-saving mode).
àST220: Set “Output signals”, "Testing SI" to "Energy-saving mode".

UFO-NT
10
"Open" and "close" safety sensor
5.1.1 Monitoring closing and opening
Standard operation
XSetting the "Contact type" parameter;
àDPS: Set
s1 and s3 to 02
("NC") (default set-
ting).
àST220: Set the "Input signals", "SI1 – terminal
SIS", "SI1 contact type" to "NC" and
"SI3 – terminal SIO", "SI3 contact type" to
"NC" (default setting).
Energy-saving mode
XSetting the "Contact type" parameter;
àDPS: Set
s1 and s3 to 03
(frequency) (default
setting).
àST220: Set the "Input signals", "SI1 – terminal
SIS", "SI1 contact type" to "frequency" and
"SI3 – terminal SIO", "SI3 contact type" to
"frequency".
XSetting the Function parameter:
àDPS: Set
f1 to the desired function and f3 to
05
(SIO stop) or
06
(SIO stop SF-GF).
àST220: Set the "Input signals", "SI1 – terminal
SIS", "SI1 function" to the desired
function and
"SI3 – terminal SIO", "SI3 function" to "SIO
stop" or "SIO stop SF GF".
S
E
GY
2
1
4
3
5
BN
BK
BU
WH
SIGNAL
24V
SIO
GND
SIS
100mA
S
1
13
10
4
SIO
SIO
GND
24VSENS
TST
1
11
10
4
SIS
SIS
GND
24VSENS
TST
E
oder
1
2
2
1
3
4
1 Opposite hinge side
2 Hinge side
3 Door transmission cable
4 GC 338 interface module

UFO-NT
11
"Open" and "close" safety sensor
5.1.2 Monitoring opening
Standard operation
XSetting the "Contact type" parameter:
àDPS: Set
s3 to 02
("NC")
(default setting).
àST220: Set the "Input signals", "SI3 – terminal SIO",
"SI3 contact type" to "NC"
(default setting).
àS1, S2: Set parameter 9 to 02 (NC).
Energy-saving mode
XSetting the "Contact type" parameter;
àDPS: Set s3 to 03 (frequency)
.
àST220: Set the "Input signals", "SI3 – terminal SIO",
"SI3 contact type" to "frequency".
XSetting the Function parameter:
àDPS: Set f3 to 05 (SIO stop) or
06
(SIO stop SF-GF).
àST220: Set the "Input signals", "SI3 – terminal SIO",
"SI3 function" to "SIO stop" or
"SIO stop SF GF".
àS1, S2: Set parameter 10 to 05 (SIO stop) or
06 (SIO stop SF GF).
1
13
10
4
SIO
SIO
GND
24VSENS
TST
S
E
GY
2
1
4
3
5
BN
BK
BU
WH
SIGNAL
24V
SIO
GND
SIS
100mA
2
1
3
4
1 Opposite hinge side
2 Hinge side
3 Door transmission cable
4 GC 338 interface module

UFO-NT
12
"Open" and "close" safety sensor
5.1.3 Monitoring closing
Standard operation
XSetting the "Contact type" parameter:
àDPS: Set
s1 to 02
("NC")
(default setting).
àST220: Set the "Input signals", "SI1 – terminal SIS",
"SI1 contact type" to "NC"
(default setting).
àS1, S2: Set parameter 7 to 02 (NC) (default set-
ting).
Energy-saving mode
XSetting the "Contact type" parameter;
àDPS: Set
s1 to 03
(frequency).
àST220: Set the "Input signals", "SI1 – terminal SIS",
"SI1 contact type" to "frequency".
XSetting the Function parameter:
àDPS: Set
f1 to the desired function.
àST220: Set the "Input signals", "SI1 – terminal SIS",
"SI1 function" to the desired function.
àS1, S2: Set parameter 8 to the desired function.
1
11
10
4
SIS
SIS
GND
24VSENS
TST
S
E
GY
2
1
4
3
5
BN
BK
BU
WH
SIGNAL
24V
SIO
GND
SIS
100mA
1
2
3
4
1 Opposite hinge side
2 Hinge side
3 Door transmission cable
4 GC 338 interface module
5.2 Safety sensor GC342
àSafety sensor GC342
àFollow installation instructions GC 342
àAccessories (optional)
àRemote control, mat. no. 100061
àFor further accessories see installation instructions GC 342
Sensor position
XMount safety sensor to the door leaf as indicated in the GC 342 installation instructions.
XSet the testing parameters.
àDPS: Set
Te to 03
(testing with GND).
àST220: Set "Output signals", "Testing SI" to "Testing with GND".

UFO-NT
13
"Open" and "close" safety sensor
5.2.1 Monitoring closing and opening
1
-UB
+UB
COM
+
SIO
60 mA
Test
SIS
GC 342
BGS
BN
GN
YE
WH
PK
GY
BU
RD
SIO
13
1 GND
4 24VSEN
S
10 TST
SIO
SIS
11
1 GND
4 24VSEN
S
10 TST
SIS
GC 342
BS
1 Door transmission cable
GC 342 settings
àSee installation instructions GC 342.
àGEZE recommends using the optional remote control to change the sensor parameters.
DCU8 settings
XSetting the "Contact type" parameter:
àDPS: Set s1 and s3 to 02 ("NC") (default setting).
àST220: Set the "Input signals", "SI1 – terminal SIS", "SI1 contact type" to "NC" and
"SI3 – terminal SIO", "SI3 contact type" to "NC" (default setting).
XSetting the Function parameter:
àDPS: Set
f1 to the desired function and f3 to 05
(SIO stop) or 06 (SIO stop SF-GF).
àST220: Set the "Input signals", "SI1 – terminal SIS", "SI1 function" to the desired function and "SI3 – terminal
SIO", "SI3 function" to "SIO stop" or "SIO stop SF GF".
5.2.2 Monitoring opening
1
SIO
13
1 GND
4 24VSEN
S
10 TST
SIO
-UB
+UB
COM
+
SIO
60 mA
Test
SIS
GC 342
BS
BN
GN
YE
WH
PK
GY
BU
RD
1 Door transmission cable
DCU8 settings
XSetting the "Contact type" parameter:
àDPS: Set s3 to 02 (NC) (default setting).
àST220: Set the "Input signals", "SI3 – terminal SIO", "SI3 contact type" to "NC” (default setting).
XSetting the Function parameter:
àDPS: Set
f3 to 05
(SIO stop) or 06 (SIO stop SF-GF).
àST220: Set the "Input signals", "SI3 – terminal SIO", "SI3 function" to "SIO stop" or "SIO stop SF GF".

UFO-NT
14
"Open" and "close" safety sensor
5.2.3 Monitoring closing
1
SIS
11
1 GND
4 24VSENS
10 TST
SIS
-UB
+UB
COM
+
SIO
60 mA
Test
SIS
GC 342
BGS
BN
GN
YE
WH
PK
GY
BU
RD
1 Door transmission cable
DCU8 settings
XSetting the "Contact type" parameter:
àDPS: Set s1 to 02 ("NC") (default setting).
àST220: Set the "Input signals", "SI1 – terminal SIO", "SI1 contact type" to "NC” (default setting).
XSetting the Function parameter:
àDPS: Set
f1 to the desired function.
àST220: Set the "Input signals", "SI1 – terminal SIS", "SI1 function" to the desired function.
5.3 Safety sensor GC334
àGC 334 module, mat. no. 126410
àFollow the installation instructions
àAccessories:
àInterface GC 334, mat. no. 128306
àSpot nder, mat. no. 112321
XSetting the testing:
àDPS: Set
Te to 02
(testing with GND).
àST220: Set "Output signals", "Testing SI" to "Testing with GND".
àMax. 6 modules in series
5.3.1 Monitoring closing and opening
XSetting the "Contact type" parameter:
àDPS: Set s1 to 02 (NC) and
s3 to 02
(NC) (default setting).
àST220: Set the "Input signals", "SI1 – terminal SIS1",
"SI1 contact type" to "NC" and
"SI3 – terminal SIO1", "SI3 contact type"
to "NC"(default setting).
XSetting the Function parameter:
àDPS: Set
f1 to the desired function and f3 to
05
(SIO stop) or 06 (SIO stop SF GF).
àST220: Set the "Input signals", "SI1 – terminal
SIS1", "SI1 function" to the desired func-
tion and "SI3 – terminal SIO1", "SI3 func-
tion" to "SIO stop" or "SIO stop SF GF".
àConguration of the GC 334 modules on the
àHinge side: DIP1 = ON
àOpposite hinge side: DIP1 = OFF
SIS
1GND
11 SIS
10 TST
424VSENS
1GND
13 SIO
10 TST
424VSENS
SIO
VT
PK
GC 334 BS
WH
YE
BN
-
+GN
BU
-
+RD
GC 334 Module BS
GC 334 Module BGS
60mA
1
1 Door transmission cable

UFO-NT
15
"Open" and "close" safety sensor
5.3.2 Monitoring opening
XSetting the "Contact type" parameter:
àDPS: Set
s3 to 02
(NC) (default setting).
àST220: Set the "Input signals", "SI3 – terminal
SIO1" and "SI3 contact type" to "NC"
(default setting).
XSetting the Function parameter:
àDPS: Set
f3 to 05
(SIO stop) or 06 (SIO stop
SF-GF).
àST220: Set the "Input signals", "SI3 – terminal
SIO1" and "SI3 function" to "SIO stop" or
"SIO stop SF GF".
àGC334 module conguration: DIP1 = ON
1GND
13 SIO
10 TST
424VSENS
SIO
GC 334 BS
WH
YE
BN
-
+GN
BU
-
+RD
GC 334
Module
60mA
1
PK
VT
1 Door transmission cable
5.3.3 Monitoring closing
XSetting the "Contact type" parameter:
àDPS: Set
s1 to 02
(NC)
(default setting).
àST220: Set the "Input signals", "SI1 – terminal
SIS1" and "SI1 contact type" to "NC"
(default setting).
XSetting the Function parameter:
àDPS: Set
f1 to the desired function.
àST220: Set the "Input signals", "SI1 – terminal
SIS1" and "SI1 function" to the desired
function.
àGC334 module conguration: DIP1 = OFF
1GND
11 SIS
10 TST
424VSENS
SIS
GC 334 BGS
WH
YE
BN
-
+GN
BU
-
+RD
GC 334
Module
60mA
1
PK
VT
1 Door transmission cable

UFO-NT
16
"Open" and "close" safety sensor
5.3.4 GC 334 connection over interface GC 334
1GND
13 SIO
10 TST
424VSENS
SIO
Interface
GC 334
4
3
2
5
111 SIS
SIS
GC 334
BS
-
+
-
+
GC 334 Module
BS
GC 334 Module
BGS
60mA
1
1 Door transmission cable
5.4 Safety sensor GC335
àGC335 master module, mat. no.128074
GC335 extension kit (slave module with accessories), mat. no. 128072
àFollow the installation instructions
àAccessories:
àGC 332 adapter, mat. no. 124035
àSpot nder, mat. no. 112321
XUse the reference body, mat. no. 120190, to set the detection eld.
XAlways install the master module near the hinge, connection with the drive control takes place at the master
module.
XConnect max. 7 slave modules to one master module.
XOpen the conguration bridge at the last slave module or at the master module (if no slave modules con-
nected).
XSet the "Testing" parameter.
àDPS: Set
Te to 01 (testing with 24 V).
àST220: Set "Output signals", "Testing SI" to "Testing with 24 V".

UFO-NT
17
"Open" and "close" safety sensor
5.4.1 Monitoring closing and opening
XSetting the "Contact type" parameter:
àDPS: Set
s1 to 02
(NC) and
s3 to 02
(NC) (default setting).
àST220: Set the "Input signals", "SI1 – terminal SIS1", "SI1 contact type" to "NC" and
"SI3 – terminal SIO3", "SI3 contact type" to "NC" (default setting).
XSetting the Function parameter:
àDPS: Set
f1 to the desired function and
f3 to 05
(SIO stop) or 06 (SIO stop SF GF).
àST220: Set the "Input signals", "SI1 – terminal SIS1", "SI1 function" to the desired function and
"SI3 – terminal SIO1", "SI3 function" to "SIO stop" or "SIO stop SF GF".
GC 335
Slaves
1GND
13 SIO
10 TST
424VSENS
GC 335 Master
BGS
SIO
1GND
11 SIS
10 TST
424VSENS
SIS
WH
BN
GY
GN
PK
YE
6
5
4
3
2
1
60mA-
+
Test
GC 335 Master
BS
6
5
4
3
2
1
60mA-
+
Test
1
2
3
4
5
6
7
8
9
10
-
+
Test
GC 332
Adapter
WH
BN
GY
GN
PK
YE
GC 335
Slaves
1
1 Door transmission cable

UFO-NT
18
Mechanical contact
5.4.2 Monitoring opening
XSetting the "Contact type" parameter:
àDPS: Set
s3 to 02
(NC) (default setting).
àST220: Set the "Input signals", "SI3 – terminal
SIO1" and "SI3 contact type" to "NC"
(default setting).
XSetting the Function parameter:
àDPS: Set
f3 to 05
(SIO stop) or 06 (SIO stop
SF-GF).
àST220: Set the "Input signals", "SI3 – terminal
SIO1", "SI3 function" to "SIO stop" or
"SIO stop SF GF".
1GND
13 SIO
10 TST
424VSENS
SIO
GC 335 Master
BS
6
5
4
3
+ 2
- 1
60mA
Test
GC 335
Slaves 1
1 Door transmission cable
5.4.3 Monitoring closing
XSetting the "Contact type" parameter:
àDPS: Set
s1 to 02
(NC) (default setting).
àST220: Set the "Input signals", "SI1 – terminal
SIS1" and "SI1 contact type" to "NC"
(default setting).
XSetting the Function parameter:
àDPS: Set
f1 to the desired function.
àST220: Set the "Input signals", "SI1 – terminal
SIS1" and "SI1 function" to the desired
function.
1GND
11 SIS
10 TST
424VSENS
SIS
GC 335 Master
BGS
6
5
4
3
+ 2
- 1
60mA
Test
GC 335
Slaves 1
1 Door transmission cable
6 Mechanical contact
àThe input KB is active in the AU, LS and NA modes of operation.
àIn the case of 2-leaf systems, the mechanical contact can be connected to the active leaf control or to the pas-
sive leaf control.
àUpon activation, the active leaf opens and, if switched on, the passive leaf opens.
àDuring activation, the output of the mechanical contact is closed, and 24V is applied at the KB input (NO con-
tact). 0 V is applied to the contact set as the normally closed contact.
The state of the drive to which the ST220 is connected is displayed.
XPress the button.
XSelect "Active leaf para" or "Passive leaf para" using the or key and press the key.
For further settings, see the descriptions below.
àSetting the "Contact type" parameter:
àWith DPS: Set c6 to 01 (NO contact) or 02 (NC).
àWith ST220:Set the "Signals", "Input signals", "KB", "KB contact type" to " NO contact " or "NC".
6.1 Key switch
àSet the Contact type parameter with:
àDPS: Set
c6 to 01 (factory setting).
àST220: Set the "Signals", "Input signals", "KB", "KB
contact type" to " NO contact " (default
setting).
àKey switch SCT, single-pole, ush-mounted, AS500 with-
out euro prole half cylinder, mat. no. 117996
àAccessories:
àEuro Prole half cylinder, mat. no. 090176
àAdditional contact, mat. no. 024467
20 KB
324V
KB

UFO-NT
19
Contact sensor inside
7 Contact sensor inside
àThe input KI is active in the operating modes AU and LS.
àIn the case of 2-leaf systems the contact sensor inside (KI) can be connected to the active leaf control or to the
passive leaf control.
àUpon activation, the active leaf opens and, if switched on, the passive leaf opens.
The state of the drive to which the ST220 is connected is displayed.
XPress the button.
XSelect "Active leaf para" or "Passive leaf para" using the or key and press the key.
For further settings, see the descriptions below.
àThe sensor for monitoring closing can also be used as a contact sensor inside.
àSet the parameters with:
àDPS: Set
f1 to 03.
àST220: Set the "Signals", "Input signals", "SI1 – terminal SIS1", "SI1 function" to "SIS and KI".
àAn activation delay time can be set for the KI input. This time is added to the general activation delay time
(opening delay).
àSet the parameters with:
àDPS: Set
ia to the desired delay time (0 s ... 9 s).
àST220: Use the or keys to set "Signals" "Input signals", "KI" or "KI delay" to the desired delay time
(0s … 9s) and press the key.
7.1 GC 302 R radar movement detector
àUpon activation, the output of the GC 302 R is closed (24
V applied to the KI input).
àSet the Contact type parameter with:
àDPS: Set
ci to 01 (default setting).
àST220: Set the "Signals", "Input signals", "KI" and
"KI contact type" to " NO contact " (default
setting).
àGC 302 R black, mat. no. 124087
àGC 302 R according to RAL, mat. no. 124088 (remote con-
trol does not work if cover tted, LED not visible).
àThe GC 302 R is a directionally sensitive radar movement
detector.
àObserve the installation instructions.
àAccessories:
àRemote control, mat. no. 099575
àCeiling installation kit, mat. no. 115384
àRain cover, mat. no. 115339
WH
BU
BK
BN
50 mA +
UB
-
UB
GC 302 R
1
2
3
4
5
24VSENS
KI
GND
4
21
1
KI
7. 2 Push button (oating normally opened contact)
àSet the Contact type parameter with:
àDPS: Set
ci to 01 (NO contact) (default setting).
àST220: Set the "Signals", "Input signals", "KI" and "KI
contact type" to " NO contact "
(default setting). 21 KI
GND
4
1
24VSENS
KI

UFO-NT
20
Contact sensor outside
8 Contact sensor outside
àThe KA input is only active in the AU mode of operation.
àIn the case of 2-leaf systems, the contact sensor outside can be connected to the active leaf control or to the
passive leaf control.
àUpon activation, the active leaf opens and, if switched on, the passive leaf opens.
The state of the drive to which the ST220 is connected is displayed.
XPress the button.
XSelect "Active leaf para" or "Passive leaf para" using the or key and press the key.
For further settings, see the descriptions below.
àThe sensor for monitoring closing can also be used as a contact sensor outside.
àSet the parameters with:
àDPS: Set
f1 to 04.
àST220: Set the "Signals", "Input signals", "SI1 – terminal SIS1", "SI1 function" to "SIS and KA".
àAn activation delay time can be set for the KA input. This time is added to the general activation delay time
(opening delay).
Set the parameters with:
àDPS: Set
aa to the desired delay time (0 s ... 9 s).
àST220: Use the or key to set "Signals", "Input signals", "KA", "KA delay" to the desired delay time
(0s … 9s) and press the key.
8.1 GC 302 R radar movement detector
àFor information see GC 302 R (KI).
àUpon activation, the output of the GC 302 R is closed (24
V applied to the KA input).
àSet the Contact type parameter with:
àDPS: Set
cO to 01 (default setting).
àST220: Set the "Signals", "Input signals", "KA" and
"KA contact type" to " NO contact " (default
setting).
WH
BU
BK
BN
50 mA +
UB
-
UB
GC 302 R
1
2
3
4
5
24VSENS
KA
GND
4
23
1
KÂ
8.2 Push button (oating normally opened contact)
àFor information see push button (KI).
àSet the Contact type parameter with:
àDPS: Set
cO to 01 (default setting).
àST220: Set the "Signals", "Input signals", "KA" and
"KA contact type" to " NO contact " (default
setting).
23 KA
1GND
424VSENS
KA