Gira 0425 00 User manual

Mini radio blind actuator
Order-No. : 0425 00
Operationsmanual
1 Safety instructions
Electrical equipment may only be installed and fitted by electrically skilled persons.
Failure to observe the instructions may cause damage to the device and result in fire and
other hazards.
Danger of electric shock. Always disconnect device before working on it. At the same
time, take into account all circuit breakers that supply dangerous voltage to the device.
Danger of electric shock. Device is not suitable for disconnection from supply voltage.
The radio communication takes place via a non-exclusively available transmission path,
and is therefore not suitable for safety-related applications, such as emergency stop and
emergency call.
For parallel connection of several motors to an output it is essential to observe the
corresponding instructions of the manufacturers, and to use a cut-off relay if necessary.
The motors may be destroyed.
Use only Venetian blind drives with mechanical or electronic limit switches. Check the
limit switches for correct adjustment. Observe the specifications of the motor
manufacturers. Device can be damaged.
Danger of electric shock. The antenna has basic insulation. Do not lead it through the
appliance box.
Do not shorten, extend or strip the antenna. Device can be damaged.
These instructions are an integral part of the product, and must remain with the end
customer.
Risk of injury. Use the device only for controlling Venetian blind and roller shutter
motors or awnings. Do not use it to switch other loads.
2 Device components
picture 1
(1) Shutter actuator
(2) Programming button
(3) LED, two-colour
1/7
32534912 29.07.2010
Mini radio blind actuator
449056 I00
Radio bus system

(4) Antenna
3 Function
System information
By statute, the reception characteristics and the antenna cannot be changed.
The device may be operated in all EU and EFTA countries.
The declaration of conformity can be viewed on our website.
The range of a radio system from the transmitter to the receiver depends on various
circumstances.
The range of the system can be optimised by selecting the optimal installation location, taking
into account the structural circumstances.
picture 2: Reduced range due to structural obstacles
Example of penetration of various materials:
Material Penetration
Wood, Plaster, Plasterboard approx. 90%
Brick, Chipboard approx. 70%
Reinforced concrete approx. 30%
Metal, Metal grid approx. 10%
Rain, Snow approx. 1-40%
Intended use
- Radio-controlled operation of a Venetian blind or roller shutter motor
- Operation with suitable radio transmitters
- Installation in appliance box to DIN 49073
Product characteristics
End positions of the Venetian blind can be called up via light scenes
4 Operation
Operation with radio transmitter
A radio transmitter has to be taught in order to be able to operate the Venetian blind actuator.
i Observe the instructions for the radio transmitter.
Depending on how a radio transmitter is operated, the slats are adjusted or the Venetian blind is
moved.
32534912 449056 I00 29.07.2010 2/7
Radio bus system
Mini radio blind actuator

5 Information for electrically skilled persons
5.1 Fitting and electrical connection
DANGER!
Electrical shock when live parts are touched.
Electrical shocks can be fatal.
Before carrying out work on the device or load, disengage all the
corresponding circuit breakers. Cover up live parts in the working environment.
Connecting and mounting the Shutter actuator
Maintain a distance of at least 0.5 m from metal surfaces and electrical devices, e.g. Venetian
blind and roller shutter motors, hi-fi and TV systems.
Maintain a distance of at least 1 m between the shutter actuator and a transmitter in order to
prevent overmodulation of the Shutter actuator.
picture 3
o Connect Venetian blind actuator (1) in accordance with connection diagram (picture 3) with
connection terminals (see Using connection terminals), and connect with the Venetian blind
or roller shutter motor (5).
32534912 449056 I00 29.07.2010 3/7
Radio bus system
Mini radio blind actuator

picture 4
o Insert the Shutter actuator in the appliance box in such a way that the programming button
and the LED are visible.
o Lay the antenna stretched out freely if possible.
o Switch on mains voltage.
Test operation on the device.
The Venetian blind can be moved by pressing the programming button briefly (for about
1 second).
Reaction LED
1st button-press Venetian blind moves up,
2 min
red
2nd button-press Stop OFF
3rd button-press Venetian blind moves down,
2 min
green
4th button-press Stop OFF
Using the lamp terminals
picture 5: Stripping length
o Strip 9 - 11 mm of the cable (picture 5).
32534912 449056 I00 29.07.2010 4/7
Radio bus system
Mini radio blind actuator

picture 6: Connection of the fine-wire cable
o Push the terminal together on the side with the square opening and connect a fine-wire
cable (picture 6).
picture 7: Connection of the single-stranded cable
o Push the single-stranded cable into the round opening on the installation side up to the
stop (picture 7).
5.2 Commissioning
i Observe the instructions for the radio transmitter.
DANGER!
Electrical shock when live parts are touched.
Electrical shocks can be fatal.
Before working on the device, cover up live parts in the working environment.
Teaching a radio transmitter
i If all memory slots are occupied, a radio transmitter which has already been taught must
first be deleted. To do this, delete all taught channels and light scenes of the radio
transmitter individually.
The distance between the receiver and the radio transmitter is from 0.5 m to 5 m.
The load is switched off.
i When a radio transmitter is being taught, the Venetian blind is likewise moved each time
the programming button of the Venetian blind actuator is pressed.
o Press the programming button of the Venetian blind actuator for approx. 4 seconds.
32534912 449056 I00 29.07.2010 5/7
Radio bus system
Mini radio blind actuator

The LED blinks. The device is in programming mode for approx. 1 minute.
o Press radio transmitter
LED lights up red. The radio transmitter has been taught.
i Teach light scene buttons separately.
Exit programming mode
The Venetian blind actuator is in programming mode.
o Press the programming button briefly.
Venetian blind actuator switches to the operating mode.
i The programming mode is exited automatically after about 1 minute.
Saving the end position of the Venetian blind in a light scene
The upper or lower end position of a Venetian blind can be called up via light scene buttons of a
radio transmitter.
Light scene button of the radio transmitter has been taught in the actuator.
o Move Venetian blind to the desired end position. The Venetian blind actuator must switch
off by itself.
o Press desired light scene button of the radio transmitter for at least 3 seconds.
The end position of the Venetian blind has been saved as a light scene.
Deleting radio transmitters individually
o Teach the radio transmitter to be deleted again (see Teaching a radio transmitter).
LED blinks quickly. The radio transmitter has been deleted.
i If several channels or light scenes of a radio transmitter have been taught, they all must be
deleted individually.
6 Appendix
6.1 Technical data
Rated voltage AC 230 V ~
Mains frequency 50 / 60 Hz
Ambient temperature -20 ... +55 °C
Relative humidity approx. 0 % ... 65 % (No moisture
condensation)
Change-over time for direction change approx. 1 s
Switch-on time, Venetian blind operation approx. 2 min
Connected load
Motors 700 W
Circuit breaker max. 10 A
Switching current for AC 230/240V~ Ohmic 6 A
Contact type µ contact
Connection
Single stranded 1.0 ... 2.5 mm²
Dimensions Ø×H 52.5×27.5 mm
Ø Centre hole 7.5 mm
carrier frequency 433.42 MHz (ASK)
Teachable radio transmitter max. 14
6.2 Troubleshooting
Device does not respond, or only sometimes.
Cause 1: battery in the radio transmitter is empty.
Change the battery in the radio transmitter.
Cause 2: Radio range exceeded. Structural obstacles reduce the range.
Check the installation situation.
32534912 449056 I00 29.07.2010 6/7
Radio bus system
Mini radio blind actuator

Check routing of antenna. Laying the antenna stretched out increases the range.
Using a radio repeater.
6.3 Warranty
We provide a warranty as provided for by law.
Please send the unit postage free with a description of the defect to our central customer
service via your specialised dealer:
Gira
Giersiepen GmbH & Co. KG
Service Center
Dahlienstraße 12
42477 Radevormwald
Germany
Gira
Giersiepen GmbH & Co. KG
Elektro-Installations-
Systeme
Industriegebiet Mermbach
Dahlienstraße
42477 Radevormwald
Postfach 12 20
42461 Radevormwald
Deutschland
Tel [phone] - 602-0
Fax [phone] - 602-399
www.gira.de
[email protected]
32534912 449056 I00 29.07.2010 7/7
Radio bus system
Mini radio blind actuator