Godox SL Series User manual

SL Series Video Light
INSTRUCTION MANUAL
Made in China

:2
:0755-29609320(8062):0755-25723423:[e-mail]
godox.com
Add: Building 2, Yaochuan Industrial Zone, Tangwei Community, Fuhai Street, Bao’an District,
Shenzhen, China Tel: [phone](8062) Fax: [phone]
E-mail: [email protected]
GODOX Photo Equipment Co., Ltd.
705-SL0000-03


QCPASS
SL

注意事项
请勿将摄影灯放置在高温、高湿的地方。
此机有温度保护功能，当温度过高时进入保护状态，当温度降低后恢复正常。
请勿用湿手接触产品，亦不可将产品浸入水中或暴露于雨中。
请勿拆卸或改造产品。若本产品因为摔落或其他意外事故造成破损，请将产品送至
厂家授权的维修中心进行检查维修。
01
02
03
04
05
06
07
08
09
10
11
12
13
主机：
01. LED灯珠
02. 灯珠保护罩
03. 散热片
04. 附件卡槽
05. ON/OFF开关
06. 调节旋钮+SET按钮
C
风扇停转符号
频道(16)组别(6)
亮度
温度
LCD液晶显示屏
部件
07. CH/GRP按钮
08. AC电源插座
09. 天线
10. LCD屏(蓝底白字)
11. 托架
12. 伞孔
13. 方向调节把手
前言
感谢您购买神牛产品！
SL系列摄影灯光源稳定，显色性好，功能强大，非常适用于影棚拍摄、采访布光、
静物拍摄以及视频拍摄等。此灯具有2种型号：白光版(5600K)、黄光版(3300K)，配备
专用遥控器，可无线分组调光，无线调节亮度，功能丰富，操作便捷。产品具有以下亮
点：
● 100W/150W/200W大功率LED灯珠，亮度高，光源稳定
● 显色指数高达93以上，R9高达80以上，真实还原物体色彩
● 大液晶屏高清显示，参数自动保存
● 专门设计灯珠保护罩，避免灯珠因触摸、碰撞引起损坏
● 配备紫铜散热片与内置风扇高效散热，具有温度控制保护，延长灯珠使用寿命
类型
白光版(色温5600K)
黄光版(色温3300K)
型号
SL-100W/SL-150W/SL-200W
SL-100Y/SL-150Y/SL-200Y

操作说明
1、开始使用摄影灯
● 连接AC电源。
● 按ON/OFF按钮，摄影灯开始发光。
● LCD显示主机当前信息
2、亮度/色温调节
亮度调节
● 在常态时，旋转主机上的调节旋钮可对亮度进行调整；
● 可调节亮度范围：10%~100%。
3、温度显示
● 本机时时检测LED摄影灯的温度，温度过高时自动关机，杜绝安全隐患；
● 长按2秒SET按钮，可使温度在摄氏度与华氏度之间互相切换。
4、亮度/色温调节
本产品具备无线遥控功能，使用433MHz无线技术，无视角限制，距离远，可同时分
别控制6个摄影灯。16组传输频道，抗干扰能力强。
● 使用前请把摄影灯主机和遥控器的频道与组别调至一致。
● 使用白光版时，请把遥控器的色温值固定在5600K；
● 使用黄光版时，请把遥控器的色温值固定在3300K
主机频道/组别调整
● 在常态时，按CH/GRP按钮，此时组别闪烁，旋转调节旋钮可选择组别(A~F)；
● 在常态时，按CH/GRP按钮2次，此时频道闪烁，旋转调节旋钮可选择频道(1~16)；
遥控器频道/组别调整
● 在常态时，按CH/GRP按钮，此时组别闪烁，旋转调节旋钮可选择组别(A~F)；
● 在常态时，按CH/GRP按钮2次，此时频道闪烁，旋转调节旋钮可选择频道(1~16)；
遥控器亮度/色温参数调节
● 在常态时，按 "-" "+" 按钮可对亮度调整；
● 在常态时，按SET按钮1次，此时色温值闪烁，按 "-" "+" 按钮可对色温调整；
其他操作说明(遥控器另购)
● 按遥控器的ON/OFF按键，可打开或者关闭所有组别的摄影灯。
● 长按遥控器“SET”按钮2秒，可打开或者关闭当前组别的摄影灯。
● 长时间不使用，请取出电池。
当本机内部有异常时，LCD相应显示会闪烁进行提示。
1、风扇因故障停止转动后，II图标闪烁提示。
2、散热片温度>70℃时，温度闪烁提示，摄影灯停止运行。
附件
电源线
灯头保护罩
反光罩

设计和规格如有变更，恕不另行通知。
产品参数
For your safety:
Do not place in high temperature or high humidity conditions.
If this product overheats, it will cease operation and resume working after cooling
down. This is due to the built-in overtemperature protection.
Do not handle with wet hands, immerse in water, or expose to rain.
Do not dissemble or modify this product. Should the product break open as the
result of a fall or other accident, send the defective back to authorized service
center for inspection and maintenance.
摄影灯
AC电源供电
频道
组别
功率
色温
100%光照度
(LUX)
100%光通量
(Lm)
显色指数
R9
TLCI(Qa)
调光范围
工作环境温度
LED灯珠
安全温度
产品尺寸
净重
黄光版
SL-100Y
黄光版
SL-150Y
黄光版
SL-200Y
白光版
SL-100W
AC 100~240V 50/60Hz
16个
6组(ABCDEF)
100W
6500(1米)
13000
>93
>80
>95
10%~100%
-10~50度
≤70℃
34x23x13cm
(不含灯头保护罩)
约2.41kg
白光版
SL-150W
150W
7200 (1米）
16000
34x23x13cm
(不含灯头保护罩)
约2.39kg
白光版
SL-200W
200W
12000 (1米）
20000
39x23x13cm
(不含灯头保护罩)
约3.16kg
5600K±200K 3300K±200K 5600K±200K3300K±200K 5600K±200K 3300K±200K
Foreword:
Thank you for purchasing this Godox Product!
SL Series video lights are excellent for product shooting, photojournalistic and video
recording, etc. It creates stable light resource and even illumination for photography.
Two models are available: White Version (5600K), Yellow Version (3300K).
Features:
● 100W/150W/200W LED bulbs guarantee high light brightness
● The color rendering index is over 93 and R9 is over 80, presenting the objects
authentically
● Wirelessly adjust light brightness
● Wireless 433MHz grouping system (6 groups & 16 channels)
● Large-sized LCD panel. Settings auto saved
● With temperature control function to prevent overheating
● With specialized protect cover to protect the LED beads
● With red copper heatsink and built –in fan to offer excellent heat dissipation
Type
White Version(Color Temperature 5600K)
Yellow Version(Color Temperature 3300K)
Model
SL-100W/SL-150W/SL-200W
SL-100Y/SL-150Y/SL-200Y

C
01
02
03
04
05
06
07
08
09
10
11
12
13
Parts
Body
01. LED Beads
02. Protect Cover
03. Heatsink
04. Accessory Slot
05. ON/OFF Power Switch
06. Select Dial + SET Button
07. CH/GRP Button
08. AC Power Jack
09. Antenna
10. LCD Panel (White in Blue)
11. Mounting Bracket
12. Umbrella Input
13. Direction Adjusting Handle
Fan Stop Sign
Channel (16)
Controllable
Group (6)
Light
Brightness
Temperature
LCD Panel
Accessories
Using the Video Light
● Connect the light with AC power jack.
● Press the ON/OFF Power Switch, the video light begins to giving out light.
● LCD panel shows the information.
Light Brightness Adjustment
● Turn the select dial to adjust the light brightness.
● The light brightness adjustable range is at 10%~100%.
Temperature Indication
● This video light checks its temperature at any time to avoid dangerous situations.
It will auto power off when the temperature is too high.
● Press the SET button for 2 seconds and the temperature can be switched between
Celsius and Fahrenheit.
Operation
Power Cord
Lamp Cover
Standard Reflector

Wireless Remote Control
With 433 MHz wireless system, this product has remote grouping and control function.
Up to 6 groups of video lights can be controlled. 16 channels are available with strong
anti-interference capability.
● Please set the channels and groups of video light to the same as those of remote
control before usage.
● When using the White Version, please set the color temperature of the remote control
as 5600K constantly;
● When using the Yellow Version, please set the color temperature of the remote control
as 3300K constantly;
Adjusting Channel/Group of the Video Light
● Press the CH/GRP button and the group icon blinks. Turn the select dial to choose a
group ID (A to F).
● Press the CH/GRP button twice and the channel icon blinks. Turn the select dial to
choose a channel ID (1 to 16).
Adjusting Channel/Group of the Remote Control
● Press the CH/GRP button and the group icon blinks. Press the”-““+” button to choose
a group ID (A to F).
● Press the CH/GRP button twice and the channel icon blinks. Press the”-““+” button to
choose a channel ID (1 to 16).
Adjusting Light Brightness/Color Temperature with the Remote Control
● Press the”-““+” button to adjust the light brightness.
● Press the SET button of the remote control once and the color temperature icon blinks.
Press the”-““+” button to adjust the color temperature.
Other Operation Tips:
● Pressing the ON/OFF button on the remote control can turn on/off all the video light
groups.
● Pressing the “SET” button on the remote control for 2 seconds can turn on/off the
current video light group.
● Please remove the battery if the light will not be used for an extended period of time.
When there are some abnormal situations in the inner video light, the relevant
LCD signs will blink as warnings. For example:
1. When the fan stops working due to fault, II signs will blink to alarm.
2. When heatsink’ temperature is over 70 Celsius degrees, the temperature
on the LCD panel will blink and the video light will stop working.
* Product design and specifications are subject to change without notice.
Technical Data:
Note: Remote control purchased separately
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Video Light
AC Power Supply
Channel
Group
Power
Color Temperature
100% Illuminance
(LUX)
100% Luminous
Flux
Color Rendering Index
R9
TLCI(Qa)
Light Brightness Range
Operation Temperature
Safe Temperature
Dimension
Net Weight
5600K±200K 3300K±200K3300K±200K 5600K±200K 3300K±200K 5600K±200K
SL-100W
AC 100~240V 50/60Hz
16
6 groups (A, B, C, D, E, F)
100W
6500(1m)
13000
>93
>80
>95
10%~100%
-10~50°C
≤70°C
34x23x13cm
Approx. 2.41kg
SL-100Y
SL-150W
150W
7200 (1m)
16000
34x23x13cm
Approx. 2.39kg
SL-150Y SL-200W
200W
12000 (1m)
20000
39x23x13cm
Approx. 3.16kg
SL-200Y
(Not included the Lamp Cover) (Not included the Lamp Cover) (Not included the Lamp Cover)
White Version Yellow Version White Version Yellow Version White Version Yellow Version





























()




12
3
12

 0755-29609320-8062



  

  









()
()




Warranty
Dear customers, as this warranty card is an important certificate to apply for our
maintenance service, please fill in the following form in coordination with the seller
and safekeep it. Thank you!
Note: This form shall be sealed by the seller.
Applicable Products
The document applies to the products listed on the Product Maintenance lnformation (see
below for further information). Other products or accessories (e.g. promotional
items,giveaways and additional accessories attached,etc.) are notincluded in this warranty
scope.
Product
Information
Model Product Code Number
Name Contact Number
Address
Customer
Information
Seller
Information
Note:
Name
Contact Number
Address
Date of Sale
If maintenance service is needed, you can directly contact the product distributor or
authorized service institutions. You can also contact the Godox after-sale service call and
we will offer you service. When applying for maintenance service, you should provide valid
wananty card. If you cannot provide valid warranty card, we may offer you maintenance
service once confirmed that the product or accessory is involved in the maintenance scope,
but that shall not be considered as our obligation.
The guarantee and service offered by this document are not applicable in the following
cases: . The product or accessory has expired its warranty period; . Breakage or
damage caused by inappropriate usage, maintenance or preservation, such as improper
packing, improper usage, improper plugging in/out external equipment, falling off or
squeezing by external force, contacting or exposing to the improper temperature, solvent,
acid, base, flooding and damp environments, etc; . Breakage or damage caused by non-
authorized institution or staff in the process of installation, maintenance, alternation,
addition and detachment; . The original identifying information of product or accessory
is modified, alternated, or removed; . No valid warranty card; . Breakage or damage
caused by using illegally authorized, nonstandard or non-public released software; .
Breakage or damage caused by force majeure or accident; . Breakage or damage that
could not be attributed to the product itself. Once met these situations above, you should
seek solutions from the related responsible parties and Godox assumes no responsibility.
The damage caused by parts, accessories and software that beyond the warranty period or
scope is not included in our maintenance scope. The normal discoloration, abrasion and
consumption are not the breakage within the maintenance scope.
How to Get the Maintenance Service
Inapplicable Cases
Warranty Period
The warranty period of products and accessories isimplemented according to the relevant
Product Maintenancelnformation. The warranty period is calculated from the day(purchase
date) when the product is bought for the first time,And the purchase date is considered as
the date registered onthe warranty card when buying the product.
Godox After-sale Service Call 0755-29609320-8062
Maintenance and Service Support Information
The warranty period and service types of products are implemented according to
the following Product Maintenance Information:
Product Type
Parts
Other Items
Name
Circuit Board
Battery
Electrical parts e.g.battery charger,
power cord, sync cable, etc.
Flash tube, modeling lamp, lamp body,
lamp cover, lockingdevice, package, etc.
Maintenance
Period(month)
12
3
12
No
Warranty Service Type
Customer sends the
product to designated site
Without warranty
Customer sends the
product to designated site
Customer sends the
product to designated site